Exotic steels...why?
-
To me, using 'exotic' metal(or more accurately, paying for expensive steel) for blade is my attempt to tilt the balance between responsible/knowledgeable use vs emergency/occational abuse.
I know enough that using the tip of blade to pry or as an awl is a no-no, or batoning may roll or chip the edge, or dropping knife on ground tip down might bent/break the tip; but it is good to know that I do have the option to do so under stressful or emergency situation.
At the end of the day, I think what's more important is not whether the steel is 'exotic' or 'expensive', but whether the price is reasonable vs performance. If the budget allows and the exotic steel does offer better performance where I want it, I won't mind paying a premium for it. Of course, if it is for collection purposes, that's entirely a different realm. :D
-
I mainly play around with traditional knives where 440C and D2 are the common exotics. :D
Additionally you tend to see people buying the newer steels and then realising that they can not sharpen them with their old sharpeners.
Some steels are better suited to special tasks (e.g. for chopping wood you need a "forgiving" steel) so there is a reason for their selection. Most of the times it has to do with having something newer and hopefully better.
The main issue seems to be the price as knives with newer steels seem to cost more; and a lot more than the cost of the new steel justifies.
If I had the choice of a knife with 440A steel and the same knife with S30V (an older exotic) at the same price I would take the S30V one.
Google brings this summary up:
http://zknives.com/knives/articles/knifesteelfaq.shtml -
One factor I think a lot of people overlook, which from what I understand is quite important in that it makes a significant difference in how easy your cutting tasks are, is the width of the blade in total.
So not only the angle of the edge, but the entire blade. Since if you are trying to cut through something, while it may be the edge that does the cutting, friction of the material on the edges of the knife blade will increase the force you need to apply. So it is possible to compensate for a duller blade by it being thinner, in comparison to a sharper blade, which is fatter. And this links back to soft steels vs hard steels.
-
@ToolJoe said:
All I have to say is two words...utility knife!One of the reasons why utility blades and scalpels are so good at cutting is because of their very thin profile. They are not made of super steels, but even when not as sharp as they originally are, they will still feel easier to cut with than a sharper but thicker blade, because you have less friction on the sides of the blade with what you are cutting through.
-
All I have to say is two words...utility knife!
Like a Stanley?
I believe so. If my understanding is correct, are lockable blades illegal in the UK?
Yes and no. If you are stopped by a policeman and you have a knife that is over 3" or is locking then you have to be able to justify having it. If you're a chef on the way to work and you're carrying chefs' knives, that's fine. If you're a farmer and you're carrying a locking folder that you're going to be using at work, that's fine. If you're a randomer in the street, that's not. At the same time, you can carry a sub 3" slipjoint without "reason", but the moment you threaten someone with it you're breaking the law. Same with a limp carrot. If you're going around threatening someone with a limp carrot and a lettuce leaf then you're in violation of the Offensive Weapons act.
All I have to say is two words...utility knife!
One of the reasons why utility blades and scalpels are so good at cutting is because of their very thin profile. They are not made of super steels, but even when not as sharp as they originally are, they will still feel easier to cut with than a sharper but thicker blade, because you have less friction on the sides of the blade with what you are cutting through.
Aren't utility blades high carbon non stainless steel and therefore pretty hard?
-
I believe so.
-
All my utility knives have SS blades.
I do not recall seeing any carbon ones, in regular shops. -
Here is a recent thread on utility knives, by the way: :D
-
I have come to the conclusion that the best compromise for the majority of people is:
- relatively soft steel from a good manufacturer - means it will be properly heat treated, easy to resharpen, relatively cheap (and so more easy to use and abuse, and replace if need be)
- Very thin blade profile overall - will give superior cutting ability, even when the edge may not be at its sharpest
- stainless steel - corrosion resistant, no need to worry about rust with normal daily usage
Based on the above, my perfect knife is a swiss army knife blade.
-
All my utility knives have SS blades.
I do not recall seeing any carbon ones, in regular shops.I the one I ever go seem to be high carbon and rust like crazy.
sent from Nate's mobile
Yeah, my current batch of regular blades are carbon (rusty ::) ) and hook blades are SS.
The come in both varieties.
-
Blade design and edge geometry are generally more important than steel . The best steel is limited by a suboptimal heatreat .
All that said , I'd prefer 154CM with a primo heat threat , than 425 with a primo heat treat .
I'm well equipped for sharpening , so that's not too much of a factor .
Enviromental considerations factor in , ie: in a pocket enviroment , in high humidity I'd prefer H1 or 440 C to 154CM , or 630V .
My favs are 440 , 154CM , A2 , and D2 ( assuming perfect heat treat in every case ) .
Chris
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
