My bargain basement ebay MP600 purchase
-
I might disassemble both sides, just to give all the parts a good cleaning before reassembly.
And I'll try to remember to take pics.
-
Okay, so here's the tool taken down, with initial cleaning.
The broken blade stubs can be seen on the far right of the tool lineup.

-
If you are interested, I do have a serrated blade for you, or maybe a saw out of another Gerber - Not sure about scissors, but will have a look.
Looking good so far, Lynn. -
I would definitely like a pair of scissors, if you had them laying around.
Also, since I don't think I've seen this descibed here, I though I'd demonstrate how I reassembled the plier head assembly.
First, Here is a picture of the parts: The plier head, the tool body, two retention buttons, two button springs, and two retention clips.

-
Turn the retention buttons hollow side up, and insert the button springs.

-
Carefully set button with spring into the hole in the plier assembly. Be careful not to lose that spring.

-
Set the plier head into the tool body, with the loose button and spring facing up. This lets gravity hold it in place for you.

-
Set the retention clip over the protruding pins and retention button. The clip should have the worn side facing down (against the tool body) and the open end facing the plier head.

-
With pliers or vice grips, place one jaw against the back of the retention clip (the side away from the plier head), and the other against the pin nearest the plier head. Ensure that the front opening (of the retention clip) is aligned with the notches in the forward pin. Apply gentle pressure to the plier or vice grip, and the retention clip will slide into place.

-
Flip the tool over, and open the arms of the body
-
Repeat steps 2-5 with the other side.

And, for reference, removing the retention clips is much the same as installing them, except that you put the jaw of your plier or vise grip on the front edge of the clip, and back pin, to force the clip off. Of very IMPORTANT note, also is that you should very gently raise the tool body arm so you don't send the retention button and button spring flying off like missiles from a 1970's Battlestar Galactica toy.
I think that about covers it.
-
-
Awesome, great play by play ! Thumbs up
Swiss Army knives .
-
So the blade arrived from Kirk today, from across the pond, and i continued with reassembly.
I... uhhh... heh. I forgot to keep track of which tools were where, and in what order, so I reassembled the tool going off of some photos of the MP600.
So, reassembling this tool is apparently an exercise in jenga-like motor skills, coupled with language exercise in creating new swear words. I tried about four times before I got one side done. However, once you do, it's a little easier the second time.
So, the method that worked for me.
Hold the tool handles so they are parallel to the surface you're working on. Put the pin on the work surface, with shaft facing up. Put the pin through the hole in the handle (with the 4 notches in it) so just about an eight of an inch sticks through the handle.

Set your first tool of the stack so the pin is protruding through it. This was one of the trickiest parts in the operation. I found that using something to hold the long tool horizontal made the process easier. In my case, I used a folded place mat to prop up the other end of the file pictured.

Set a washer on top of the tool. It is important to note that the small tab on the washer should be toward the end of the tool, facing the side with the locking tab, and should slot into the opening on the tool handle just past the locking tab.

Lower the tool body slightly, to allow more of the pin to protrude through the handle, and repeat the process until all tools are in place. Once they are, you may find that the pin does not want to line up with the hole in the tool handle to finish being pushed into place. Pulling back on the locking tab should allow the pin to come into alignment. Once it does, push it the rest of the way through, and thread the screw into the hollow end. Tighten the nut to finger tight, then use pliers or vice grips to tighten more, checking to ensure the tools inside the handle are still able to move freely.
Flip the tool over, and repeat with the other tool handle.
In this process, it's important to make sure that those small tabs on the washers are in the slot behind the locking tab. It should look like this when properly installed. You can see the small metal tabs on the washers protruding in the slot behind the locking tab.

And... that's it. My first tool disassembly/reassembly. Much thanks to Kirk for the blade. This old MP600 still has a broken blade stub but that really doesn't matter to me. It has one decent blade, and as I mostly got it to mess around with, I'm fine with it as is.
-
I'm pleased to hear the blade made it ok! Nice step by step guide through the guts of a Gerber Lynn

-
to Kirky for hooking Lynn up with the blade, and thanks Lynn for the pics. I'm thinking about combining my MP400 and 450 to make a bladeless 425, but was a bit nervous about tearing apart two perfectly good tools and ending up with a pile of parts I can't figure out. Think it's gonna be time soon to give it a shot. -
How come your thinking bladeless JD?
-
Simply because I rarely use the blades on my MT's. I always have a folder on me, either a dedicated one or a SAK, and sometimes both. My multitools are there for the drivers, pliers, file, etc. With the file from the 450 replacing the blade in the 400, I can have sliding pliers, scissors, and a file in one compact package.
At work the pliers are not used every day, but often enough that they're good to have around. A blade is used dozens of times a day, opening boxes, cutting material for samples, etc. My usual working blade is a Kerhaw Needs Work, a Wharncliffe-bladed OHO tank that's basically a utility knife on steroids. Add a Tinker or a traditional slipjoint to the mix, and I'm well covered in terms of cutting things. The MP's blade sees almost no use at all. -
Great walk through Lynn.

-
That is a nice pictorial, Lynn. Thanks.
I find it easier when I use a Nail inserted from the other side of the plier handle to kepp the already installed tools in place while you are reaching for the next washer and tool.
And holding the plier handle in a vise or somehow clamped to the table might be helpful, too.
Lastly, after several dis- and reassemblys, I think it´s best to insert the tools while the plier head is out, this gives you more room.Still, sometimes I do invent new swear words, too. ;)
-
Nice photo tutorial Lynn, and congrats on your first tear down & rebuild!

-
Without this post ( I know it's 6 months old) I would still be trying to put my MP600 back together
Thanks Lynn -
Wow. It's super cool that this was useful to someone. Very glad to help.

-
It really is a great thread Lynn.

-
Thanks.
One of the best photo tutorials I've seen.
:) :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login