What did you use your Leatherman for today?
-
I used my ST300, bit kit, & the 00 bit to disassemble my son's Kindle Fire, so that I could re-solder the charging port to the main board.
the j-rod
-
Cool!
that's us mobile, eh.
-
@forbygrace said:

Was pulled into a scale house by the state troopers, had to fix a very bad air leak under my tractor. Usually have to call a mobile mechanic $90+ parts labor... Thank god and because of the new leatherman I purchased I did it my self. Even the officer commented "who helped you"?? :) I replied god and this leatherman!Sent from my iPhone using Tapatalk
Good story, and welcome to the forum

-

Was pulled into a scale house by the state troopers, had to fix a very bad air leak under my tractor. Usually have to call a mobile mechanic $90+ parts labor... Thank god and because of the new leatherman I purchased I did it my self. Even the officer commented "who helped you"?? :) I replied god and this leatherman!Sent from my iPhone using Tapatalk
Good story, and welcome to the forum

thank you kindly
Sent from my iPhone using Tapatalk
-
I've used my TTi today to cut cardboard, remove staples from crates, tighten screws, and used the file to fix the slit in a flat head screw so it could be removed.
-
Thats a great story @forbygrace! Leatherman to the rescue and back on the road for you. Welcome to MTo
-
Used my juice s2 in my mates bar tonight to fix his till. Then used it to sort some wiring out in the jukebox. The juice was used with a micro Phillips out of his edc. Meh ordered a leatherman wingman while I was there too as he does a few small repairs on the place.
Sent from my iPhone using Tapatalk
-
Yes thank you I am extremely proud to be part of this forum
Sent from my iPhone using Tapatalk
-
@forbygrace said:
Yes thank you I am extremely proud to be part of this forumSent from my iPhone using Tapatalk
Welcome aboard, nice little store, back when I was 17 I ran into something similar and didn't have any tools and yet was over an hour out. And the only thing I had was my gerber(first one they ever came out with) wow did it save my ***! JR
Oh, if your wondering it was my throttle spring and linkage, good thing I had a spring loaded pen in my school bag! Any way welcome again, you should do a full intro in the new member forum.
-
Very good story on your part, thank you for your warm welcoming! I will indeed check out your recommendations.
Sent from my iPhone using Tapatalk
-
I used the file on my BORebar and extended the handles to reach inside a trap to set the latch/trigger mechanism. We have a cat that has been living under our trailer for the winter it seems. One benefit is that we haven't noticed any mice or squirrels in quite a while, which would be something we'd see every so often.
-
@Monrogue said:
I used the file on my BORebar and extended the handles to reach inside a trap to set the latch/trigger mechanism. We have a cat that has been living under our trailer for the winter it seems. One benefit is that we haven't noticed any mice or squirrels in quite a while, which would be something we'd see every so often.That could be because is just so stinking cold there
I doubt you'd even see the cat around with those crazy temps 
-
Today, using my Surge, I fixed a reciprocating meat slicer at work. Dummies can't seem to understand the concept of tightening the bolts and screws on the spinning razor blade thingy.
The world belongs to the funkiest.
-
Sliced some knobs off an old worn tire with my Sidekick to make a makeshift commuter tire for my bike.
-
I used the file on my BORebar and extended the handles to reach inside a trap to set the latch/trigger mechanism. We have a cat that has been living under our trailer for the winter it seems. One benefit is that we haven't noticed any mice or squirrels in quite a while, which would be something we'd see every so often.
That could be because is just so stinking cold there
I doubt you'd even see the cat around with those crazy temps 
That's a good point too ;) Haven't caught the cat yet either...
-
Use the knife blade on my ST300 to cut some sections of sarking, which were then install on my shed roof.
(for the non-Aussies here, a quote from Wikipedia):
In current usage in Australia, sarking refers to a laminated aluminium foil layer (commonly described as RFL, or reflective foil laminate) that is installed on the roof trusses, beneath the battens, supporting a tile or metal deck roof. It acts as additional radiative and convective insulation and provides a condensation barrier.
Then in the afternoon, I repaired my friend who helped me with the sarking by helping him with some plumbing. ST300 saw and file both came in handy for cutting pipe, and removing the burrs afterwards
-
i took a piece of wood.
three bulb-lights,
three tea strainers
some ironwire
and a leatherman mut....

8) -
Used the PUG to re zero the sights on my air rifle this morning. Lot of help it was,shot line an idiot :ahhh
-
@screwloose said:
i took a piece of wood.
three bulb-lights,
three tea strainers
some ironwire
and a leatherman mut....

8)That's pretty neat

-
i took a piece of wood.
three bulb-lights,
three tea strainers
some ironwire
and a leatherman mut....

8)That's pretty neat

That is pretty neat, but did you use for the wings? JR
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login