And so it begins.... (My adventures into Alox!)
-
about the scalpel- you could have a raised nail knick ala the scissors on the China sacks. It's not elegant for sure, but it would work.
-
Im down to a critically low amount of scissors backsprings for 93mm alox now, so I forced myself to sit down at the computer and work on a new file. Ver 2.0 of the backspring is pretty much the same, but with some tweaks to make it easier to sand and finish, and also strengthen it.
I was always worried about the strength of the spring over the pivot hole so I beefed that up a bit. I use a 1/2 inch sanding mandrel to finish the inside edges and it could never get into the tight area near then end where the scissors tip rests so I increased that radius. The end of the spring that engages the scissors pivot is also slightly thicker which should give the scissors a bit more snap.
Now I have to wait 3-4 weeks for the waterjet, then heat treat, so hopefully in 2 months I should be restocked.

-
@Syph007 said:
Im down to a critically low amount of scissors backsprings for 93mm alox now, so I forced myself to sit down at the computer and work on a new file. Ver 2.0 of the backspring is pretty much the same, but with some tweaks to make it easier to sand and finish, and also strengthen it.I was always worried about the strength of the spring over the pivot hole so I beefed that up a bit. I use a 1/2 inch sanding mandrel to finish the inside edges and it could never get into the tight area near then end where the scissors tip rests so I increased that radius. The end of the spring that engages the scissors pivot is also slightly thicker which should give the scissors a bit more snap.
Now I have to wait 3-4 weeks for the waterjet, then heat treat, so hopefully in 2 months I should be restocked.
Ever evolving, I like that.

Oh and what happened to the liner lock?

-
It's real cold up in the great white north atm. The Others are coming! Don't begrudge a man for enjoying the comforts of his warm computer during the big freeze of 14.
-
-
-
@Syph007 said:
Im down to a critically low amount of scissors backsprings for 93mm alox now, so I forced myself to sit down at the computer and work on a new file. Ver 2.0 of the backspring is pretty much the same, but with some tweaks to make it easier to sand and finish, and also strengthen it.I was always worried about the strength of the spring over the pivot hole so I beefed that up a bit. I use a 1/2 inch sanding mandrel to finish the inside edges and it could never get into the tight area near then end where the scissors tip rests so I increased that radius. The end of the spring that engages the scissors pivot is also slightly thicker which should give the scissors a bit more snap.
Now I have to wait 3-4 weeks for the waterjet, then heat treat, so hopefully in 2 months I should be restocked.
I had a few emails out for quotes and the lowest one I got was actually a local guy about 20 minutes from here. I prefer to use local when I can so Im going over to drop the steel off now. He said 3 weeks. I'm somewhat nervous trying a new shop but if it works out it will be nice to have a local guy I can trust. I would then consider using him to cut a bunch of brass liners out as a next test as cutting them manually... SUCKS! :D
The waterjet pricing is interesting. It works out to somewhere between 3-6 bucks a part, but it depends on how much taper you can accept on the edges. For zero taper its the most expensive as the machine has to go the slowest. Luckily my tolerances are no where near as high as that. For the cheapest cut price it will only have 0.006" of taper over the 0.110" thickness of the steel. That is completely acceptible for me, since I will still need to edge finish anyhow.
Now watch my luck as I get 200 new springs in and Vic decides to kill the 93mm alox liner for 2014...

-
Will the center hole also be cut by the waterjet or do you drill it yourself?
-
-
Any plans on how you finish the springs? Batch-wise? Or the full lot in an era of eternal darkness? :D
-
@crackout said:
Any plans on how you finish the springs? Batch-wise? Or the full lot in an era of eternal darkness? :DWell the first time I heat treated these I didnt know to ask for them to be done in a vaccuum. This time I will so there should be significantly less finish work.
The first batch took ALOT of effort to get one heavily oxidized spring to polished state.

A nice size semi-pro level tumbler can be got for around 5-700. If the springs need alot of work, I might just go for it and get the tumbler to speed finish them. But I will wait to see how they are when back from heat treating.
-
Hope it all turns out good. And I wouldn't worry about Vic canceling the 93's. ;) They'll be around for a long time.
And the waterjet pricing looks interesting. I'm thinking of a MTO project that's been on hold for too long.
-
@enki_ck said:
Hope it all turns out good. And I wouldn't worry about Vic canceling the 93's. ;) They'll be around for a long time.And the waterjet pricing looks interesting. I'm thinking of a MTO project that's been on hold for too long.
I went in and dropped off the steel. Im old fashioned with this type of stuff and I really like doing business face to face and being able to discuss the job and other options.
He was a really nice and knowledgeable fellow so I cant wait to get the parts back. He said cutting brass liners would be no problem so I'm going to bring in a few square feet of brass next and give that a try. I looked at his samples of edge finishes for the various tapers and I went with the cheapest option as it looked fine to me. So I should be just around $3.25 a part if my math is correct. As long as im under $10 per finished spring Im happy. The steel was about $200, and im not sure what heat treat will be but I think a finished spring should be around $8.
-
Ok... a few updates.
Orange hard anodized is delayed for another week! :(
I got restocked on red parts though. :D


I also ground a test blade to try with that liner lock I cut....


It locks up perfectly, BUT there is a problem I didnt see ahead of time. Can you see the issue?
-
No stop pin? Locks at 90°?
-
-
You reply too fast...
Blade locks at 90°?
-
-
Maybe if you make the cut like this...

-
The locking part of the liner/scale must extend almost up to the pivot so that the 90° part of the blade doesn't lock.
And the blade has to be modified so that in the locking position the part of the blade is short enough to fit behind the locking mechanism.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
