And so it begins.... (My adventures into Alox!)
-
I just got a call that my waterjet order is done. New springs! Looks like the cut fee worked out to about 3.25 a part.
-
-
It's hovering around 0 C today. Not too bad at all actually.
I stopped by the waterjet place! :D




You can see the ver 2.0 (top) of the spring has more meat over the pivot and better curves for faster finishing.
I got a tip from the waterjet buy about a heat treat place right here in town so Im going to check them out tomorrow and get these things done. :D
I might see about getting them tumbled as well to eliminate the labor intensive manual sanding part, but we'll see.
-
-
It's hovering around 0 C today. Not too bad at all actually.
I stopped by the waterjet place! :D

0°C that's horrible!
Hey that mesh looks cool, what are you gonna do with it? Radiator grill for your car? :D
Actually i needed some grating at the front of my garage to make a drain and I was going to use it for that! :D Its still plenty strong.
Oh I checked with the local heat treat place here and guess what... THEY DO DLC TOO!
Guess who's dumping BO on stainless for PVD-DLC now.... :ahhh
-
-
...
Oh I checked with the local heat treat place here and guess what... THEY DO DLC TOO!Guess who's dumping BO on stainless for PVD-DLC now.... :ahhh
:ahhh

:ahhh
Now this is gonna be sweeet. :D
I know I got excited!
I sent them off a quote request so we'll see if if I can afford it. It would be a nice upgrade to the BO as it can have inconsistent results with blotchiness on occasion.
DLC tools and anodized Ti scales and liners....

-
@Syph007 said:
I know I got excited!I sent them off a quote request so we'll see if if I can afford it. It would be a nice upgrade to the BO as it can have inconsistent results with blotchiness on occasion.
DLC tools and anodized Ti scales and liners....

:ahhh :ahhh :ahhh
You just made my day!! Way too much awesomeness!!
-
My abstinence from finally ordering my Pioneer pays off with every new post. :D
-
Copper alox with red liners, with a clip point blade from a day packer.
It took some fiddling to get that clip point to fit, but it worked out fine. The blade is much thinner than a standard 93mm blade so it needed a 0.030" washer, but its nice and stable.






-
Interesting build, but beautiful as always Syph
JR -
@MadPlumbarian said:
Interesting build, but beautiful as always Syph
JR+1
-
That's cool, and very different.

-
Nice. Did you use same pivot hole? I just cut a bit off and drilled a new one. Frustrating to beat material into exisitng.

-
Love that clip point! :)
-
@rickinFL said:
Nice. Did you use same pivot hole? I just cut a bit off and drilled a new one. Frustrating to beat material into exisitng.No I did a Vic trick like they do to put pruner/electrician blades on 91mm SAKs. Just tighten the spring a bit and you dont notice. That pivot was 3.5mm anyhow and the 3.2 mm pivots were fine in that. Thats even less than putting a 3.0 holed tool on a 2.5mm pin like Vic does.
I thought about shortening the blade, but it was already feeling kind of stubby so I left it as is.
-
Ok so when I get mine???
As soon as I make a bunch more! Still waiting on CNC parts then I will crank these out in large numbers.
Bump! :wave: :)
Sent from my iPhone using Tapatalk
-
Ok so when I get mine???
As soon as I make a bunch more! Still waiting on CNC parts then I will crank these out in large numbers.
Bump! :wave: :)
Sent from my iPhone using Tapatalk
My stepper motors are still sitting on my desk. :D Too cold for me to get that conversion done yet. Im thinking april / may is more realistic. :D
-
Nice. Did you use same pivot hole? I just cut a bit off and drilled a new one. Frustrating to beat material into exisitng.
No I did a Vic trick like they do to put pruner/electrician blades on 91mm SAKs. Just tighten the spring a bit and you dont notice. That pivot was 3.5mm anyhow and the 3.2 mm pivots were fine in that. Thats even less than putting a 3.0 holed tool on a 2.5mm pin like Vic does.
I thought about shortening the blade, but it was already feeling kind of stubby so I left it as is.
Thanks for that. That is worlds easier than my route. Hoping to send the blade off for a reprofile as well on my next attempt.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

