And so it begins.... (My adventures into Alox!)
-
...
Oh I checked with the local heat treat place here and guess what... THEY DO DLC TOO!Guess who's dumping BO on stainless for PVD-DLC now.... :ahhh
:ahhh

:ahhh
Now this is gonna be sweeet. :D
I know I got excited!
I sent them off a quote request so we'll see if if I can afford it. It would be a nice upgrade to the BO as it can have inconsistent results with blotchiness on occasion.
DLC tools and anodized Ti scales and liners....

-
@Syph007 said:
I know I got excited!I sent them off a quote request so we'll see if if I can afford it. It would be a nice upgrade to the BO as it can have inconsistent results with blotchiness on occasion.
DLC tools and anodized Ti scales and liners....

:ahhh :ahhh :ahhh
You just made my day!! Way too much awesomeness!!
-
My abstinence from finally ordering my Pioneer pays off with every new post. :D
-
Copper alox with red liners, with a clip point blade from a day packer.
It took some fiddling to get that clip point to fit, but it worked out fine. The blade is much thinner than a standard 93mm blade so it needed a 0.030" washer, but its nice and stable.






-
Interesting build, but beautiful as always Syph
JR -
@MadPlumbarian said:
Interesting build, but beautiful as always Syph
JR+1
-
That's cool, and very different.

-
Nice. Did you use same pivot hole? I just cut a bit off and drilled a new one. Frustrating to beat material into exisitng.

-
Love that clip point! :)
-
@rickinFL said:
Nice. Did you use same pivot hole? I just cut a bit off and drilled a new one. Frustrating to beat material into exisitng.No I did a Vic trick like they do to put pruner/electrician blades on 91mm SAKs. Just tighten the spring a bit and you dont notice. That pivot was 3.5mm anyhow and the 3.2 mm pivots were fine in that. Thats even less than putting a 3.0 holed tool on a 2.5mm pin like Vic does.
I thought about shortening the blade, but it was already feeling kind of stubby so I left it as is.
-
Ok so when I get mine???
As soon as I make a bunch more! Still waiting on CNC parts then I will crank these out in large numbers.
Bump! :wave: :)
Sent from my iPhone using Tapatalk
-
Ok so when I get mine???
As soon as I make a bunch more! Still waiting on CNC parts then I will crank these out in large numbers.
Bump! :wave: :)
Sent from my iPhone using Tapatalk
My stepper motors are still sitting on my desk. :D Too cold for me to get that conversion done yet. Im thinking april / may is more realistic. :D
-
Nice. Did you use same pivot hole? I just cut a bit off and drilled a new one. Frustrating to beat material into exisitng.
No I did a Vic trick like they do to put pruner/electrician blades on 91mm SAKs. Just tighten the spring a bit and you dont notice. That pivot was 3.5mm anyhow and the 3.2 mm pivots were fine in that. Thats even less than putting a 3.0 holed tool on a 2.5mm pin like Vic does.
I thought about shortening the blade, but it was already feeling kind of stubby so I left it as is.
Thanks for that. That is worlds easier than my route. Hoping to send the blade off for a reprofile as well on my next attempt.
-
Syph, I have a question for you.
Its part idle curiosity & part genuine interest but its been bugging me all day and I have looked though the thread but I didn't see anything to answer it.
What is the largest 84mm SAK you can practically make? For example could you make something like a 5 layer ranger or even a 84mm champion or swisschamp?
-
@Cauldronborn said:
Syph, I have a question for you.Its part idle curiosity & part genuine interest but its been bugging me all day and I have looked though the thread but I didn't see anything to answer it.
What is the largest 84mm SAK you can practically make? For example could you make something like a 5 layer ranger or even a 84mm champion or swisschamp?
If you had the 84mm size parts you can slap as many together as you like. If you mean, take them from the 91mm size then no, alot of them wouldnt fit very well, like pliers, mag / phillips etc.
-
@papercut said:
Wenger parts can also be used,.but many many recruits will need.to be sacrificed fo this for their backsprings. Two examples are the 84mm huntsman PTR made and.the uber cadet with pliers and more by Steve. Scribs may have done.some.as.well .So are you saying a Wenger 85mm part will fit on a vic 84? JR
-
Yes 85 wenger will fit with modifications. I've done 85 pliers in a 84 frame. Some work but yes.
Sent from my iPhone using Tapatalk
-
Ok, I ran a search & re-read some of the earlier posts and I'm hooked.

Smurf you all!!

I've just **GOT **to get one now. :ahhh
But before I go any further, Syph are you still doing 84mm alox mods? I can't remember seeing anything one way or the other.
If so are you able to take orders?
Thanks for your time.
-
Nope all done with 84 alox. The scales are annoyingly thin to work with. I like the 93mm alox as it can be countersunk nicely and maintain good frame rigidity.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login