And so it begins.... (My adventures into Alox!)
-
Ok so when I get mine???
As soon as I make a bunch more! Still waiting on CNC parts then I will crank these out in large numbers.
Bump! :wave: :)
Sent from my iPhone using Tapatalk
-
Ok so when I get mine???
As soon as I make a bunch more! Still waiting on CNC parts then I will crank these out in large numbers.
Bump! :wave: :)
Sent from my iPhone using Tapatalk
My stepper motors are still sitting on my desk. :D Too cold for me to get that conversion done yet. Im thinking april / may is more realistic. :D
-
Nice. Did you use same pivot hole? I just cut a bit off and drilled a new one. Frustrating to beat material into exisitng.
No I did a Vic trick like they do to put pruner/electrician blades on 91mm SAKs. Just tighten the spring a bit and you dont notice. That pivot was 3.5mm anyhow and the 3.2 mm pivots were fine in that. Thats even less than putting a 3.0 holed tool on a 2.5mm pin like Vic does.
I thought about shortening the blade, but it was already feeling kind of stubby so I left it as is.
Thanks for that. That is worlds easier than my route. Hoping to send the blade off for a reprofile as well on my next attempt.
-
Syph, I have a question for you.
Its part idle curiosity & part genuine interest but its been bugging me all day and I have looked though the thread but I didn't see anything to answer it.
What is the largest 84mm SAK you can practically make? For example could you make something like a 5 layer ranger or even a 84mm champion or swisschamp?
-
@Cauldronborn said:
Syph, I have a question for you.Its part idle curiosity & part genuine interest but its been bugging me all day and I have looked though the thread but I didn't see anything to answer it.
What is the largest 84mm SAK you can practically make? For example could you make something like a 5 layer ranger or even a 84mm champion or swisschamp?
If you had the 84mm size parts you can slap as many together as you like. If you mean, take them from the 91mm size then no, alot of them wouldnt fit very well, like pliers, mag / phillips etc.
-
@papercut said:
Wenger parts can also be used,.but many many recruits will need.to be sacrificed fo this for their backsprings. Two examples are the 84mm huntsman PTR made and.the uber cadet with pliers and more by Steve. Scribs may have done.some.as.well .So are you saying a Wenger 85mm part will fit on a vic 84? JR
-
Yes 85 wenger will fit with modifications. I've done 85 pliers in a 84 frame. Some work but yes.
Sent from my iPhone using Tapatalk
-
Ok, I ran a search & re-read some of the earlier posts and I'm hooked.

Smurf you all!!

I've just **GOT **to get one now. :ahhh
But before I go any further, Syph are you still doing 84mm alox mods? I can't remember seeing anything one way or the other.
If so are you able to take orders?
Thanks for your time.
-
Nope all done with 84 alox. The scales are annoyingly thin to work with. I like the 93mm alox as it can be countersunk nicely and maintain good frame rigidity.
-
Ok,no problem.
EDIT: Are you doing anything at all with the 84mm SAKs?
-
@Cauldronborn said:
Ok,no problem.EDIT: Are you doing anything at all with the 84mm SAKs?
Ive got a full brass conversion of an 84 right now, but that is the last one in the queue. I dont buy or stock the parts any longer.
-
Oh well it was worth a shot, I guess I'll have to have a go myself at some point.
-
Process updates!

Still waiting on hard anodized orange... Im starting to think their dye isnt good, its never taken this long for a hard anodize run.
I just dropped off springs for heat treat at an awesome local place for heat treat in vacuum! Good price and 2 day turnaround! its 5 minutes from my house!
I talked to the owner about a DLC run next.. not cheap and they have a minimum cost, but if I include enough parts I think I can get the cost per SAK to a reasonable amount. Much nicer than BO on stainless by a long margin though. If I include 20 spartans to sell after to help supplement the DLC cost I think that can work.
The problem though is that doing the moving parts ones I dont think is an easy option.. like scissors. So I could take the scissors apart and re-rivet, or not have them available.... I wonder how hard re-rivetting would be, maybe a test on an old pair of scissors is in order.
Im pretty excited now to have local electroplater, local waterjet and local heat treat / DLC. Now I just want to find a local shop for surface grinding and batch tumbling and Im set to make up whatever I need. :D
-
@Syph007 said:
Process updates!
Still waiting on hard anodized orange... Im starting to think their dye isnt good, its never taken this long for a hard anodize run.
I just dropped off springs for heat treat at an awesome local place for heat treat in vacuum! Good price and 2 day turnaround! its 5 minutes from my house!
I talked to the owner about a DLC run next.. not cheap and they have a minimum cost, but if I include enough parts I think I can get the cost per SAK to a reasonable amount. Much nicer than BO on stainless by a long margin though. If I include 20 spartans to sell after to help supplement the DLC cost I think that can work.
The problem though is that doing the moving parts ones I dont think is an easy option.. like scissors. So I could take the scissors apart and re-rivet, or not have them available.... I wonder how hard re-rivetting would be, maybe a test on an old pair of scissors is in order.
Im pretty excited now to have local electroplater, local waterjet and local heat treat / DLC. Now I just want to find a local shop for surface grinding and batch tumbling and Im set to make up whatever I need. :D
Glad to hear about all this good news!! If you don't mind me asking, how much more are we talking in regards of the DLC?
I'm still impressed on how well organized you were able to get the whole SAK moding thing. May I also ask if you're going to make more of those custom blades, now that you have a local HT?
-
@Syph007 said:
Process updates!
Still waiting on hard anodized orange... Im starting to think their dye isnt good, its never taken this long for a hard anodize run.
I just dropped off springs for heat treat at an awesome local place for heat treat in vacuum! Good price and 2 day turnaround! its 5 minutes from my house!
I talked to the owner about a DLC run next.. not cheap and they have a minimum cost, but if I include enough parts I think I can get the cost per SAK to a reasonable amount. Much nicer than BO on stainless by a long margin though. If I include 20 spartans to sell after to help supplement the DLC cost I think that can work.
The problem though is that doing the moving parts ones I dont think is an easy option.. like scissors. So I could take the scissors apart and re-rivet, or not have them available.... I wonder how hard re-rivetting would be, maybe a test on an old pair of scissors is in order.
Im pretty excited now to have local electroplater, local waterjet and local heat treat / DLC. Now I just want to find a local shop for surface grinding and batch tumbling and Im set to make up whatever I need. :D
I have done one set of scissors with a redo on the rivet. The old style with the brass rivet. It works fine :).
Sent from my iPhone using Tapatalk
-
-
Oops forgot to post some pics of the hard anodized orange scales. Heres a couple sets.

They turned out pretty sweet and its nice to have another color.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
