Mini driver question
-
I saw this mod where someone cut a hole in the end of the bit extender to use the LM driver in it. Would that be the best of both worlds?
-
Actually, the Vic mini driver is too thick to work with my glasses. The Leatherman mini driver however works great!
-
On a related topic, I compared the mini driver in the Leatherman Micra to the one in the Wenger Pocket Tool Chest. My glasses have flat head screws. The Leatherman is too big to fit, while the Wenger fits. My wife's glasses have philips head screws. The Leatherman again does not fit, while the Wenger will turn them, but it takes a fair amount of fiddling.
I want to get some Vic mini drivers for my corkscrew equipped knives, but I haven't gotten around to it yet. I wish Vic had this tool on their keychain sized models. It seems like it would be much more useful to have than a cuticle pusher, for example.
-
Well
ther's no doubt who is the Savior 


:D

:o



:ahhh


-
Actually, the Vic mini driver is too thick to work with my glasses. The Leatherman mini driver however works great!
this has been my experience as well. the LM mini driver has saved my vision several times over the years!

It's a life-saver isn't it? :D

it really is!
I can understand how the non-glasses wearing crowd might see it as a waste of space in the tool, but for some of us, it's an essential part of any EDC. :D -
Since using thread locker on my glasses I haven't had any issues at all.
-
Is the new mini driver the one on the left or is that the old one?
-
I always have the Mini Screwdriver in the corkscrew of my Victorinox Spartan - just in case. Another useful gadget/gimmick/tool that I found recently is a set of four small bits in a small driver by Ace Hardware (only about $4). The bits are magnetic and include two Phillips (PH 0 and PH 000) ad two straight slot (1.5 mm and 30 mm). The set has a shirt pocket clip, measures about 3.5 inches long and 0.5 inches diameter and makes nice MacGyver tool to go along with a Swiss Army Knife and a multitool. Very light weight, so I always carry it next to my ball point pens and penlight.

-
@Faiaoga said:
I always have the Mini Screwdriver in the corkscrew of my Victorinox Spartan - just in case. Another useful gadget/gimmick/tool that I found recently is a set of four small bits in a small driver by Ace Hardware (only about $4). The bits are magnetic and include two Phillips (PH 0 and PH 000) ad two straight slot (1.5 mm and 30 mm). The set has a shirt pocket clip, measures about 3.5 inches long and 0.5 inches diameter and makes nice MacGyver tool to go along with a Swiss Army Knife and a multitool. Very light weight, so I always carry it next to my ball point pens and penlight.
Do you have any pics or a link? I would like to see it if you don't mind :)
-
I personally use the tip of the Style CS' nail file for my glasses. Works great; it's thinner than the one on the Micra so it works on smaller screws, and you're not trying to adjust a millimeter long screw with a pound of MT in your hand. I have used the one in the Wave successfully, but I don't tend to carry my Wave around with me.
-
Wanting to see if it could be done, and also to see if it is practical, I took a standard Vic Corkscrew driver, removed the plastic with a dremel till I could see the anchored end of the steel shaft.
I then drove the steel shaft out of the plastic just far enough (maybe 1/4") to grind a Phillips flat bit on the end (about a 57 degree tip), and a small flat. I filled the small flat with JB Weld, also coated the shaft liberally, then drove the shaft back in to the plastic till the Phillips tip extended just a little. Let it all set up overnight, cleaned it up, and..................................it does work, but the shortness of the shaft overall means that either the flathead driver or the Phillips driver are a little too short to be used comfortably. The shaft length is a smidge short overall, and it can't be too much longer otherwise the steel shaft would mar the finish on the scales when the corkscrew closes.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login