Stainless Huntsman
-
Ah you already figured out what I was going to suggest, moving the phillips layer inward. The only reason the normal opener layer is on the outside is so the can opener can work, but once you remove that, its nicer to move it inwards.
-
Yep. Makes the driver easier to use too, I think. I don't think I'll thin down a Philips again though - too much effort and it now looks very skinny and a bit weedy. Next time I'll put the Phillips opposite the cap lifter and the can opener with two springs and some spacers.
-
This has slowed down a bit because I've been waiting to get my new power tools installed:
<a href="https://flic.kr/p/neib6s" target="_blank" rel="noopener noreferrer"><img src="https://farm6.staticflickr.com/5222/13933957436_757001c215_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Got all that sorted at the weekend but still waiting for fine belts for the sander, carbide drills, brass shim, M2 taps, countersink bits and some cutting oil to arrive. -
Cheap carbide drills... Have a look at these.
they are the ones I use and they are cheap as chips compared to 5 quid each.
nice range of sizes from 1.55mm to 6.5 in 0.05mm steps. and they aren't crap either.
-
@PTRSAK said:
Cheap carbide drills... Have a look at these.they are the ones I use and they are cheap as chips compared to 5 quid each.
nice range of sizes from 1.55mm to 6.5 in 0.05mm steps. and they aren't crap either.
Peter any estimate how many holes 1 bit would drill before its spent? I keep shopping around and trying different options, and some bits Ive had break on the first use, others Ive used up to 50 times fine. Ive been working out the cost per hole on various options. :D
-
hard to say, I bought a packet of 10 in 2.35mm to drill out the 2.2mm holes in SAK blades and springs when I couldn't get 2.2mm rod so I could use 3/32.
I have done quite a lot and only broken one and that was my fault in side loading it.
The one I an using now is as sharp as it was on the first hole. -
@PTRSAK said:
Cheap carbide drills... Have a look at these.they are the ones I use and they are cheap as chips compared to 5 quid each.
nice range of sizes from 1.55mm to 6.5 in 0.05mm steps. and they aren't crap either.
I think I'm going to get some of these. I've just broken the two carbide drills I got this afternoon. :'( Two problems: too much runout on the chuck of the pillar drill and too slow drill speed. Need to borrow a dial gauge from work to check the chuck.
Belt sander worked perfectly though - the fine aluminium oxide belts have given a great finish and the scales have polished up nicely.
-
Your belt sander looks just like the type I've been looking for.
Could you do me a favour & let me know the make & model details for it.
It looks like it's just the right size for the workshop I'm planning to set up in my garage (the car has lost it's home again). -
It's an Axminster: http://www.axminster.co.uk/axminster-hobby-series-aw130bd2-belt-disc-sander . I'm sure you can get the same thing cheaper elsewhere but they've got a store near work and good customer service if it goes wrong. A bit fiddly to change belts and needed some tweaking to get the platen perpendicular to the belt but works nicely. I bought the belts from johnt1102 on eBay: http://stores.ebay.co.uk/Abrasivexpertjohnt1102
-
Nice looking work

John is a good Guy to deal with for belts

-
@hiraethus said:
I think I'm going to get some of these. I've just broken the two carbide drills I got this afternoon. :'( Two problems: too much runout on the chuck of the pillar drill and too slow drill speed. Need to borrow a dial gauge from work to check the chuck.Fixed the run out issues with the chuck on the pillar drill - took the chuck apart and greased the back of the jaws to let them slide smoothly and it's much better now. Still going to borrow a dial gauge and check it properly but it's good enough for now. Just waiting for the carbide drills to arrive and then I can get on with the Huntsman.
-
Yeah, the carbide drills are very brittle. Any side or bending load and they just shatter like glass.
hint, don't try to use them in a cordless drill.
-
Got a little bit more done today. Test fitted all of the final parts (including a no-lanyard opener layer spring and older screwed scissors) after drilling them out to 3mm. Got the layers in the right order this time too:
<a href="https://www.flickr.com/photos/26008756@N08/14264028912/" target="_blank" rel="noopener noreferrer"><img src="https://farm4.staticflickr.com/3754/14264028912_5c2597b545_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Need to cut a nail nick in one of the liners for the awl because I've put the Philips in the middle, trim a bit off of the liner between the blades and saw and another little bit off the one between the saw and openers for clearance at the saw tip. Then i just need to make the barrel pins and countersink the scales. -
That is looking the business!

-
I think I'm going to have to scrap the scales. :( I was a bit overzealous shaping the edges and they're smaller than the springs and liners now. I also don't like the way the Phillips works - would have been better if I'd gone for a Phillips opposite the can opener and cap lifter. To make matters worse, instead of using threaded barrel pins I decided to peen the rivets - left too much material on and now it's too tight. Ah well, every day is a school day.
-
Gutted. You were doing so well. Better to do over and be happy than make do and be left wanting.
-
Yeah, this one was for a friend (who has been waiting very patiently for me to finish it) so had to be right.
-
Right, back on it. Stainless Huntsman is now a G10 Fieldmaster.
<a href="https://flic.kr/p/owRNox" target="_blank" rel="noopener noreferrer"><img src="https://farm6.staticflickr.com/5562/14789060315_456d66c6c9_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
G10 scales drilled, cut and sanded - gone for a matt finish which actually looks really nice. Much easier to work than the stainless - fast to sand but rather smelly. Drilled out the backside phillips and the can opener and did a trial fit. Everything works fine but I need to make some brass washers to go between the tools and the scales. I also need to make the barrel pins - I've managed to source some 3mm OD x 1.6mm ID stainless tubing so hopefully I can just tap it out to M2 for the screws. -
The stainless tube worked really well for the pivots:
<a href="https://www.flickr.com/photos/26008756@N08/14801344091/" target="_blank" rel="noopener noreferrer"><img src="https://farm3.staticflickr.com/2923/14801344091_e564eb0af6_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Might not look like much but I don't need to drill them out, just cut to length, clean the ends and tap to M2 for the screws.Not everything went to plan though:
<a href="https://www.flickr.com/photos/26008756@N08/14781458816/" target="_blank" rel="noopener noreferrer"><img src="https://farm3.staticflickr.com/2902/14781458816_6650e1dee9_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Need to work on my technique for making brass washers. -
@hiraethus said:
Right, back on it. Stainless Huntsman is now a G10 Fieldmaster.G10 scales drilled, cut and sanded - gone for a matt finish which actually looks really nice. Much easier to work than the stainless -** fast to sand but rather smelly**.
You should wear a dust mask when sanding CF and preferably sand it wet to keep the dust down even more. BAD stuff to get in your lungs.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

