First time Mod
-
Rather involved for a first mod, don't you think? You could have picked something simple, like cutting the lanyard loop off. You're making the rest of us look bad. ;)
I've found when drilling out the tools for larger pivots (I use 3mm on mine, not 1/8" because I make my own barrel pins) that you need a good finish inside the hole and that you have to remove the burrs from both ends of the hole. If you don't, the tools tend to pick up on the pivots and don't move smoothly. You also need to make sure that the pivots go into the scales for good support.
Instead of remaking the scales, you could try making your own washers from brass shim stock to space them out a bit. Fiddly job.
-
Outstanding work.
I believe your "snap" problems may be combination of things.Yes those small raised pads are important, I made some scales from CF sheet and they needed a set of mylar washers to cut down the drag between the blades/tools and the scales.
The slightest change in the relationship between the three holes in the scales and/or the position of the holes in the tangs can make quite a large change to the snap. If using barrels, they really need to be supported in the scale and not just located by the screw.
The material itself may be less rigid than Aluminium and this could have effect by flexing or even just damping the snap so it sounds less.
Just a few ideas, but I'm no expert. What you have done here is WAY beyond anything I could ever come up with.
As others have said, I'm sure you could find a market here for sets of those scales.And if you want another project... do something similar on the 91mm platform and people will beat a path to your door. Imagine a SwissChamp with scales like this. :ahhh
-
I'll just echo what others have said - WOW! beautiful work.
-
Great job!! I am a fan of 84mm and new to mod squad too. To see others came something cool like this make me excited.
Sent from my HTC One X using Tapatalk
-
Haha thanks for the welcome guys.
Yep rigidity could be an issue but the scales seem to be sitting ok...
My scales only have about 0.5mm allowance for the pivots to extend into, and whether they're doing that is hard to tell. As I mentioned, I had trouble and am not sure that my pivot trimming process was accurate.
Unfortunately/fortunately I'm sure it's against company policy to profit from projects completed in their facilities, so I will NOT be selling them! Although I molded a whole bunch so may offload a few at some point, once I know that they work properly.
J
-
Well if you just give me a pair that would be legit under company rules right?

-
One more image for good measure..
Closeup of the mold and a freshly molded pair of scales.

-
So many questions! What's the tool life like - how many parts could you get out of it? How accurate and stable is the finished part, and what are the mechanical properties? Did you do the machining (CNC I assume) yourself?
-
Wow that is very good looking! Excellent work!
-
Hmmm...maybe your company might want to expand into the SAK mod market.

-
Wow, first welcome aboard, and second I must say that is a great design, love it! JR
-
That's an excellent intro post and very impressive first mod.

Welcome to the forum.

-
Wow, nice.
You should change the design however and use button head screws for the 84mm range (thus use almost no countersinking). The reason behind this (as already stated) is to allow the pivots to extend into the scales as much as possible. The holes in the scales define the position and correct alignment of the pivots/pins which directly affects the tension of the springs and thus the snap of the tools.
The tension between the scales is by far the hardest thing to get right. I even think it's easier to get the correct amount when peening instead of using threaded pivots with screws.
-
Beautiful mod, although I would problably have gone for the second-last sketch instead, but that's just me. Nice pictures and walkthrough and nice result. I hope you get the last small parts figured out, so you'll truly be happy with your SAK. :D
-
How did I miss this so far? :D Neat idea! Someday I want to make skeletonized Ti scales as I think that would be a sweet look.
Thats an interesting factory defect, looks like the washer meant to sit with the blade, ended up on the wrong rivet. I assume you used a washer with the blade though as that will be a problem if you didnt as the blade is thinner than the backspring.
Generally though it sounds like your issue is frame rigidity, and most of that is going to be reduced by how far the pivots extend into the scales. For good rigidity you need the pivots to go in about the whole thickness of standard cadet scales. This is why countersinking them just doesn't really work on thin scales. And its why I stopped working on that size of SAK.
The pioneer thicker alox scales I work with, the pivots extend about 1.5mm into the scale and provides a nice rigid snap.
As others have mentioned if your material flexes that will be an issue too.
To test my theory of the pivot in the scale distance issue, here is what I would do. Rebuild the SAK with long rods instead of pivots as a temporary test. If all the tools work great with rods right through the scales then that is your problem.

-
Wow that looks fantastic! I can't help you with your modding questions but I think you did an exellent job

Welcome to MTo!
-
Really nice scales and concept. Perhaps you could increase the rigidity of your CF scales adding thin metal liners (like brass, for color contrast) behind them. I believe than an additional benefit is that the cutout will stand out a lot more (sort of like a filigree design).

-
Holy smurf! that's some very impressive work :ahhh
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
