Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

First time Mod

Scheduled Pinned Locked Moved The Mod Squad
55 Posts 1 Posters 9.3k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. First time Mod
First time Mod
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Jerm Offline
    Jerm
    Posts: 13
    Jerm Offline
    Jerm
    wrote on last edited by Jerm
    #27 Quote Reply

      @crackout said:
      Wow, nice.

      You should change the design however and use button head screws for the 84mm range (thus use almost no countersinking). The reason behind this (as already stated) is to allow the pivots to extend into the scales as much as possible. The holes in the scales define the position and correct alignment of the pivots/pins which directly affects the tension of the springs and thus the snap of the tools.

      The tension between the scales is by far the hardest thing to get right. I even think it's easier to get the correct amount when peening instead of using threaded pivots with screws.

      Yeah I'm thinking this is my main issue. I like the countersunk screw heads, the head is slightly larger than the the pivots so I could easily drill out the scales to allow the pivot to extend further into them, and I think there would still be enough contact with the head to hold it all together.

      Current hole geometry.

      I just need to figure out a clean and accurate method to cut the pivots down. Any suggestions?! The lathes we have are all too large, and the jaws will not grip such a small object. I may try and make a jig to clamp them in the manual mill.

      1 Reply Last reply
      • Jerm Offline
        Jerm
        Posts: 13
        Jerm Offline
        Jerm
        wrote on last edited by
        #28 Quote Reply

          @toolguy said:
          Excellent work.

          I personally don't like skeletonized scales as they present many problems but they do look cool.

          Thanks.

          Problems due to stiffness? In their current state I'm not convinced that this is the issue in my case. Also, if I make these scales slightly thicker, they will be just as stiff as the standard Alox scales. That may be something I look into down the track!

          1 Reply Last reply
          • hiraethus Offline
            hiraethus
            Admin Team
            Posts: 6,969
            hiraethus Offline
            hiraethus
            Admin Team
            wrote on last edited by
            #29 Quote Reply

              Thanks jerm. Loving your work. :tu:

              @Jerm said:
              I just need to figure out a clean and accurate method to cut the pivots down. Any suggestions?! The lathes we have are all too large, and the jaws will not grip such a small object. I may try and make a jig to clamp them in the manual mill.

              I use a collet chuck on the lathe we have here to hole the bar stock when making the pins - do you have one for any of your tools? Other option would be to hold the pin in the jaws of a drill press or mill and bring it down onto a file to remove the end.

              1 Reply Last reply
              • n4vgm Offline
                n4vgm
                Posts: 367
                n4vgm Offline
                n4vgm
                wrote on last edited by
                #30 Quote Reply

                  Welcome to MTO and envious :drool: :drool: :drool:

                  1 Reply Last reply
                  • Jerm Offline
                    Jerm
                    Posts: 13
                    Jerm Offline
                    Jerm
                    wrote on last edited by Jerm
                    #31 Quote Reply

                      I ended up finding a small collet chuck and matching collet to suit the 1/8" pivots. I used a V-block to clamp the collet chuck vertically in the manual mill. I then used an end mill to machine to the pivots down to 6.5mm.

                      I then used my 1/8" drill to drill out the scales, from the geometry shown above, to this new shape...

                      I find these things quite tricky to assemble but I got there in the end and the knife now works perfectly! :sak:

                      Added some thread-locking fluid to the screws to make sure they stay in place.

                      Thanks to everyone on here who offered comments/suggestions!

                      1 Reply Last reply
                      • sawman Offline
                        sawman
                        Posts: 9,745
                        sawman Offline
                        sawman
                        wrote on last edited by
                        #32 Quote Reply

                          @Jerm said:
                          I ended up finding a small collet chuck and matching collet to suit the 1/8" pivots. I used a V-block to clamp the collet chuck vertically in the manual mill. I then used an end mill to machine to the pivots down to 6.5mm.

                          I then used my 1/8" drill to drill out the scales, from the geometry shown above, to this new shape...

                          I find these things quite tricky to assemble but I got there in the end and the knife now works perfectly! :sak:

                          Added some thread-locking fluid to the screws to make sure they stay in place.

                          Thanks to everyone on here who offered comments/suggestions!

                          I'm glad you got it figured out, now we need more pics :pok: :D

                          1 Reply Last reply
                          • DazMechanical Offline
                            DazMechanical
                            Posts: 1,285
                            DazMechanical Offline
                            DazMechanical
                            wrote on last edited by
                            #33 Quote Reply

                              WOW! :tu: Great work and welcome to the forum!

                              Did you buy the barrels and screws from the website posted in syph007's mod thread?

                              1 Reply Last reply
                              • Jerm Offline
                                Jerm
                                Posts: 13
                                Jerm Offline
                                Jerm
                                wrote on last edited by Jerm
                                #34 Quote Reply

                                  @DazMechanical said:
                                  WOW! :tu: Great work and welcome to the forum!

                                  Did you buy the barrels and screws from the website posted in syph007's mod thread?

                                  Thanks!

                                  Yes I did. They took quite a while to get to my part of the world, but worked well in the end.

                                  More pics to come!

                                  1 Reply Last reply
                                  • DazMechanical Offline
                                    DazMechanical
                                    Posts: 1,285
                                    DazMechanical Offline
                                    DazMechanical
                                    wrote on last edited by
                                    #35 Quote Reply

                                      @Jerm said:

                                      @DazMechanical said:

                                      WOW! :tu: Great work and welcome to the forum!

                                      Did you buy the barrels and screws from the website posted in syph007's mod thread?

                                      Thanks!

                                      Yes I did. They took quite a while to get to my part of the world, but worked well in the end.

                                      More pics to come!

                                      Cool, I'm in Australia, guessing your in NZ? I've thought about getting the same barrels and screws but wasn't sure if they would ship here. I might have to give it a go.

                                      Can't wait for more pics! :D

                                      1 Reply Last reply
                                      • Cupboard Offline
                                        Cupboard
                                        Posts: 2,018
                                        Cupboard Offline
                                        Cupboard
                                        wrote on last edited by
                                        #36 Quote Reply

                                          :drool:

                                          1 Reply Last reply
                                          • Ombudsman Offline
                                            Ombudsman
                                            Posts: 828
                                            Ombudsman Offline
                                            Ombudsman
                                            wrote on last edited by
                                            #37 Quote Reply

                                              Amazing ! :salute:
                                              Those scales are indeed :drool: :drool: :drool:

                                              1 Reply Last reply
                                              • Jerm Offline
                                                Jerm
                                                Posts: 13
                                                Jerm Offline
                                                Jerm
                                                wrote on last edited by
                                                #38 Quote Reply

                                                  @DazMechanical said:

                                                  @Jerm said:

                                                  @DazMechanical said:

                                                  WOW! :tu: Great work and welcome to the forum!

                                                  Did you buy the barrels and screws from the website posted in syph007's mod thread?

                                                  Thanks!

                                                  Yes I did. They took quite a while to get to my part of the world, but worked well in the end.

                                                  More pics to come!

                                                  Cool, I'm in Australia, guessing your in NZ? I've thought about getting the same barrels and screws but wasn't sure if they would ship here. I might have to give it a go.

                                                  Can't wait for more pics! :D

                                                  Yep im in NZ.

                                                  OK, so I have a few spare sets of these scales. Who wants some?!

                                                  Would prefer to give to anyone with a bit of experience with pivot style customs knives, so I can get some feedback on the design.

                                                  I'm willing to package and post them, recipients may or may not have to pay for shipping, depending on what it ends up costing.

                                                  1 Reply Last reply
                                                  • DazMechanical Offline
                                                    DazMechanical
                                                    Posts: 1,285
                                                    DazMechanical Offline
                                                    DazMechanical
                                                    wrote on last edited by
                                                    #39 Quote Reply

                                                      Oh man I'd love to get a set of these scales! :drool:

                                                      PM sent.

                                                      1 Reply Last reply
                                                      • lowtech Offline
                                                        lowtech
                                                        Posts: 4,799
                                                        lowtech Offline
                                                        lowtech
                                                        wrote on last edited by
                                                        #40 Quote Reply

                                                          @Jerm said:

                                                          @DazMechanical said:

                                                          @Jerm said:

                                                          @DazMechanical said:

                                                          WOW! :tu: Great work and welcome to the forum!

                                                          Did you buy the barrels and screws from the website posted in syph007's mod thread?

                                                          Thanks!

                                                          Yes I did. They took quite a while to get to my part of the world, but worked well in the end.

                                                          More pics to come!

                                                          Cool, I'm in Australia, guessing your in NZ? I've thought about getting the same barrels and screws but wasn't sure if they would ship here. I might have to give it a go.

                                                          Can't wait for more pics! :D

                                                          Yep im in NZ.

                                                          OK, so I have a few spare sets of these scales. Who wants some?!

                                                          Would prefer to give to anyone with a bit of experience with pivot style customs knives, so I can get some feedback on the design.

                                                          I'm willing to package and post them, recipients may or may not have to pay for shipping, depending on what it ends up costing.

                                                          Very generous offer!

                                                          I don´t know how many spare sets you have, but let me suggest the following:
                                                          We do have a bunch of experienced modders around, if you wish some professional feedback, I´d send an example to:
                                                          Syph007, PTRSAK, RickinFL, Crackout, Hanksolon, Metropolicity ...
                                                          I don´t want to step on anyones toes and I´m aware the list is probably not complete.

                                                          But all those I mentioned are experienced modders and I could imagine they would like to have a go at those scales and show us some nice mods and share their experiences with you and the crowd.

                                                          Syph007 has probably done the most screw/pivot based SAK mods around here and knows about the difficulties of the 84 mm chassis.
                                                          The others are making less mods, but do high quality work nonetheless. Metro, while not modding SAKs on a regular basis, is an experienced modder, a product designer and has hexperience in 3D modelling and prototyping. and he mentioned he´d like to try a SAK mod some time ago.

                                                          1 Reply Last reply
                                                          • Syph007 Offline
                                                            Syph007
                                                            Global Moderators
                                                            Posts: 9,842
                                                            Syph007 Offline
                                                            Syph007
                                                            Global Moderators
                                                            wrote on last edited by
                                                            #41 Quote Reply

                                                              Ya I gave up on the 84 size mods, just not my thing I find the frame to limiting, and all my secondary produced parts like liners etc are all on the 93mm size. I think its part OCD too, I dont like the non symmetrical design. Ironically I do like the cellidor 84s, the small tinker is a favorite of mine.. so what do I know. :D

                                                              I will add though that if anyone needs a set of pivots and doesn't want to pay the expensive knifekits shipping for a few parts ( I think its $30 for international ) I can sell you a set of pivots and screws, and international shipping I can do for $6. I buy them 200 at a time so I have quite a few on hand usually and can save you some money on shipping.

                                                              Cheers

                                                              1 Reply Last reply
                                                              • lowtech Offline
                                                                lowtech
                                                                Posts: 4,799
                                                                lowtech Offline
                                                                lowtech
                                                                wrote on last edited by
                                                                #42 Quote Reply

                                                                  I did not want to force you, Syph... ;)
                                                                  I remember you would no longer offer 84 mm mods because of limited tool choices and teh thin scales - But I figured this might be tempting and you would be able to give a very educated feedback.

                                                                  1 Reply Last reply
                                                                  • Jerm Offline
                                                                    Jerm
                                                                    Posts: 13
                                                                    Jerm Offline
                                                                    Jerm
                                                                    wrote on last edited by
                                                                    #43 Quote Reply

                                                                      @lowtech said:

                                                                      @Jerm said:

                                                                      @DazMechanical said:

                                                                      @Jerm said:

                                                                      [quote author=DazMechanical link=topic=52724.msg903901#msg903901 date=1403268960]
                                                                      WOW! :tu: Great work and welcome to the forum!

                                                                      Did you buy the barrels and screws from the website posted in syph007's mod thread?

                                                                      Thanks!

                                                                      Yes I did. They took quite a while to get to my part of the world, but worked well in the end.

                                                                      More pics to come!

                                                                      Cool, I'm in Australia, guessing your in NZ? I've thought about getting the same barrels and screws but wasn't sure if they would ship here. I might have to give it a go.

                                                                      Can't wait for more pics! :D

                                                                      Yep im in NZ.

                                                                      OK, so I have a few spare sets of these scales. Who wants some?!

                                                                      Would prefer to give to anyone with a bit of experience with pivot style customs knives, so I can get some feedback on the design.

                                                                      I'm willing to package and post them, recipients may or may not have to pay for shipping, depending on what it ends up costing.

                                                                      Very generous offer!

                                                                      I don´t know how many spare sets you have, but let me suggest the following:
                                                                      We do have a bunch of experienced modders around, if you wish some professional feedback, I´d send an example to:
                                                                      Syph007, PTRSAK, RickinFL, Crackout, Hanksolon, Metropolicity ...
                                                                      I don´t want to step on anyones toes and I´m aware the list is probably not complete.

                                                                      But all those I mentioned are experienced modders and I could imagine they would like to have a go at those scales and show us some nice mods and share their experiences with you and the crowd.

                                                                      Syph007 has probably done the most screw/pivot based SAK mods around here and knows about the difficulties of the 84 mm chassis.
                                                                      The others are making less mods, but do high quality work nonetheless. Metro, while not modding SAKs on a regular basis, is an experienced modder, a product designer and has hexperience in 3D modelling and prototyping. and he mentioned he´d like to try a SAK mod some time ago.
                                                                      [/quote]

                                                                      Thanks for you input and suggestions.

                                                                      These scales are working fine now so anyone who has modified an Alox knife before shouldn’t have any trouble. I don’t think it is any more difficult to assemble than a normal Alox pivot mod.

                                                                      I have already offered some to Syph007 but he wasn’t all that interested as he doesn’t work with this size knife, as he explained above.

                                                                      I’m reluctant to contact everyone personally, but if they show interest on this thread I’ll consider sending some out to them.

                                                                      1 Reply Last reply
                                                                      • Glofindel Offline
                                                                        Glofindel
                                                                        Posts: 352
                                                                        Glofindel Offline
                                                                        Glofindel
                                                                        wrote on last edited by
                                                                        #44 Quote Reply

                                                                          @Jerm said:

                                                                          @lowtech said:

                                                                          @Jerm said:

                                                                          @DazMechanical said:

                                                                          [quote author=Jerm link=topic=52724.msg904870#msg904870 date=1403482966]
                                                                          [quote author=DazMechanical link=topic=52724.msg903901#msg903901 date=1403268960]
                                                                          WOW! :tu: Great work and welcome to the forum!

                                                                          Did you buy the barrels and screws from the website posted in syph007's mod thread?

                                                                          Thanks!

                                                                          Yes I did. They took quite a while to get to my part of the world, but worked well in the end.

                                                                          More pics to come!

                                                                          Cool, I'm in Australia, guessing your in NZ? I've thought about getting the same barrels and screws but wasn't sure if they would ship here. I might have to give it a go.

                                                                          Can't wait for more pics! :D

                                                                          Yep im in NZ.

                                                                          OK, so I have a few spare sets of these scales. Who wants some?!

                                                                          Would prefer to give to anyone with a bit of experience with pivot style customs knives, so I can get some feedback on the design.

                                                                          I'm willing to package and post them, recipients may or may not have to pay for shipping, depending on what it ends up costing.

                                                                          Very generous offer!

                                                                          I don´t know how many spare sets you have, but let me suggest the following:
                                                                          We do have a bunch of experienced modders around, if you wish some professional feedback, I´d send an example to:
                                                                          Syph007, PTRSAK, RickinFL, Crackout, Hanksolon, Metropolicity ...
                                                                          I don´t want to step on anyones toes and I´m aware the list is probably not complete.

                                                                          But all those I mentioned are experienced modders and I could imagine they would like to have a go at those scales and show us some nice mods and share their experiences with you and the crowd.

                                                                          Syph007 has probably done the most screw/pivot based SAK mods around here and knows about the difficulties of the 84 mm chassis.
                                                                          The others are making less mods, but do high quality work nonetheless. Metro, while not modding SAKs on a regular basis, is an experienced modder, a product designer and has hexperience in 3D modelling and prototyping. and he mentioned he´d like to try a SAK mod some time ago.
                                                                          [/quote]

                                                                          Thanks for you input and suggestions.

                                                                          These scales are working fine now so anyone who has modified an Alox knife before shouldn’t have any trouble. I don’t think it is any more difficult to assemble than a normal Alox pivot mod.

                                                                          I have already offered some to Syph007 but he wasn’t all that interested as he doesn’t work with this size knife, as he explained above.

                                                                          I’m reluctant to contact everyone personally, but if they show interest on this thread I’ll consider sending some out to them.
                                                                          [/quote]
                                                                          I do mod 84mm but on Brass pivot pins not barrel, so if those scales are in 2.2, 2.5 or 3mm I am sure can mod on that.

                                                                          1 Reply Last reply
                                                                          • Syncop8r Offline
                                                                            Syncop8r
                                                                            Posts: 8,801
                                                                            Syncop8r Offline
                                                                            Syncop8r
                                                                            wrote on last edited by
                                                                            #45 Quote Reply

                                                                              @Syph007 said:
                                                                              I will add though that if anyone needs a set of pivots and doesn't want to pay the expensive knifekits shipping for a few parts ( I think its $30 for international )...

                                                                              Oh REALLY? Dang, I was going to get some for a possible Wenger Ranger mod (although I don't yet know what size I'll need)...

                                                                              1 Reply Last reply
                                                                              • PTRSAK Offline
                                                                                PTRSAK
                                                                                Posts: 4,776
                                                                                PTRSAK Offline
                                                                                PTRSAK
                                                                                wrote on last edited by
                                                                                #46 Quote Reply

                                                                                  Well, I would be interested in a pair (or two).

                                                                                  Purely to give my X-Spurt opinion on naturally, not just because they are cool.

                                                                                  I'm sure a SAK assembled on these scales would fit right in to my "Recruit Parade"

                                                                                  </topic/41214

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. First time Mod
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0