Small leatherman?
-
Kick has a clip.
Sak's rule !
-
I think the Kick had an OPTION for a clip. It didn't come with one, so you'd have to hunt down an accessory for a discontinued tool. Not impossible, just not easy.
Also, sorry to say I forgot about the outside open blade with the Sideclip.
I think then the only options are Wingman and Sidekick.
-
there's also the Freestyle. it's somewhat lacking in the tools department (just a blade and pliers), but it's an option.
I'll put in another vote for the Skeletool. I love my CX for lightweight pocket carry.

-
Check out the juice range,no clip though but outside blade,or smaller you have the squirt ps4

-
For the skeletool, is it worth upgrading to the CX model?
-
@jeremy1517 said:
I have a Wave and want a nice small pocket model. I prefer a clip but not required.I also want a blade that is on the outside, if there is a model.
If you are asking for "pocket" and not "keyring" have a look at the pre-2014 Juice range (the ones with the smooth scales). A few surmountable issues but reports of backsprings breaking are a worry. I carry the S2 and like it. In terms of capability consider it a SAK with reasonable pliers. Outside accessible blade.
If you want a clip and can accept inboard tools track down a Kick (and buy a clip). I did but feel the clip detracts from the Kick's smooth lines.
-
Honestly, I would look elsewhere. Small tools are where leatherman are at their weakest. Their strength seems to lie in the 4" and 4.1/2" tools, and below that they get shoddy. I've tried a number of their smaller tools:
Style PS - weak scissor spring lasted only a few months. I have had this replaced under wartranty, but try to avoid using the scissors on this thing ... but if I do that what's the point in carrying it.
Squirts - very sloppy build quality in all the ones I've had - not as good as my Gerber Dimes. Most of the squirts have had blades that catch on the scales of the tool, plus I've had bald spots on tools, poor peening ... quite frankly, don't bother
Micra - a great tool if you can get an older model. The quality on a new one will be a lottery
Juice - in theory it's perfect, in practice it's very disappointing - don't even get me started
Skeletool - try before you buy. Some people love 'em, some people hate 'em. Not sure about current quality as I haven't handled one for a while, but worth borrowing one or trying them out in a store before handing over the readies.
My personal favourite pocketable tool at the moment is probably the Gerber Balance (though the MP400 is close too), though the Octane might be worth looking into too. Would a well equipped SAK fit the bill instead?
If you're considering another larger tool at some point in the future, then by all means explore the rest of the Leatherman range, Wave, Charge, Surge, ST300, whatever ... However, for smaller tools, Leatherman would be far from my first choice
-
@jeremy1517 said:
For the skeletool, is it worth upgrading to the CX model?when it comes to the Skeletool, I think Mr. Whippy had some great advice:
@50ft-trad said:
Skeletool - try before you buy. Some people love 'em, some people hate 'em. Not sure about current quality as I haven't handled one for a while, but worth borrowing one or trying them out in a store before handing over the readies.personally, I love the Skeletool. I got the CX when it first came out a few years ago, and it has remained one of my favorite tools to this day. (and I've picked up a couple more since then.) I think the CX version is worth the extra cost because of the 154CM steel used in the blade; the DLC coating and carbon fiber insert are just for looks.
that being said, I know there are plenty of people who dislike the ergonomics of the tool or don't get along with it for some other reason. it seems to be one of the most polarizing tools -- people seem to either love it or hate it, with very few in the middle.
-
@50ft-trad said:
Honestly, I would look elsewhere. Small tools are where leatherman are at their weakest. Their strength seems to lie in the 4" and 4.1/2" tools, and below that they get shoddy. I've tried a number of their smaller tools:Style PS - weak scissor spring lasted only a few months. I have had this replaced under wartranty, but try to avoid using the scissors on this thing ... but if I do that what's the point in carrying it.
Squirts - very sloppy build quality in all the ones I've had - not as good as my Gerber Dimes. Most of the squirts have had blades that catch on the scales of the tool, plus I've had bald spots on tools, poor peening ... quite frankly, don't bother
Micra - a great tool if you can get an older model. The quality on a new one will be a lottery
Juice - in theory it's perfect, in practice it's very disappointing - don't even get me started
Skeletool - try before you buy. Some people love 'em, some people hate 'em. Not sure about current quality as I haven't handled one for a while, but worth borrowing one or trying them out in a store before handing over the readies.
My personal favourite pocketable tool at the moment is probably the Gerber Balance (though the MP400 is close too), though the Octane might be worth looking into too. Would a well equipped SAK fit the bill instead?
If you're considering another larger tool at some point in the future, then by all means explore the rest of the Leatherman range, Wave, Charge, Surge, ST300, whatever ... However, for smaller tools, Leatherman would be far from my first choice
Wow. I don't agree with a few of those. You must have very bad luck or something.
I have had a Style PS and used the scissors literally every single day for around 2 years and never had one issue with it.
The Squirt line has been excellent for me as well. Everything is peened correctly and no rubbing on the tools to scale.
Same with the newer Micra. Admitting the last Micra I got was about a year ago, but everything is top notch on it.
I guess it just goes to show Leatherman needs to focus on quality control to make sure everyone gets a consistent product.
-
Cap'n, the knives on at least two (or was it three-I'd need to check) squirts didn't **rub **- they actually got caught up, and there was a flat spot on both knife blades and a mark on the scales from doing this. Have you experienced the (fairly common) saw on a juice getting caught up on an awl, so you have to push the saw over so it closes? Same deal here :-\ Closing the knife without pushing it inwards would get caught up everytime.
On the small tools, it seems the only thing they seem to get consistently right is the pliers. LM always made a good job of pliers - well, until they made the Rebar - not a fan of those at all as I've said many times. I don't have much faith in LM's smaller stuff at all. Nice designs, but I just haven't got any confidence in them.
-
@jeremy1517 said:
For the skeletool, is it worth upgrading to the CX model?For me, that mainly depends on how much you dislike the partly-serrated blade. Some people despise them :P (right, Lynn? ;) )
I'm not much of a steel-snob, so I don't care all too much about the fancier steel.
-
@50ft-trad said:
Cap'n, the knives on at least two (or was it three-I'd need to check) squirts didn't **rub **- they actually got caught up, and there was a flat spot on both knife blades and a mark on the scales from doing this. Have you experienced the (fairly common) saw on a juice getting caught up on an awl, so you have to push the saw over so it closes? Same deal here :-\ Closing the knife without pushing it inwards would get caught up everytime.On the small tools, it seems the only thing they seem to get consistently right is the pliers. LM always made a good job of pliers - well, until they made the Rebar - not a fan of those at all as I've said many times. I don't have much faith in LM's smaller stuff at all. Nice designs, but I just haven't got any confidence in them.
I know exactly what you mean about the Juice saw.
I'm not saying your right or wrong in any way. I'm just saying I have not had those bad experiences with the PS, Micra, and Squirt line.
-
Welcome to the forums.

I have not had any problems with the Style, Squirt or Micra tools.
I also dislike combo edges.
I haven't tried the Skeletool CX but do think I would like it.Is the Wave with the removable pocket clip not to your liking?
-
I don't have a pocket clip for the wave yet. I thought I'd like to try something smaller and lighter than the wave.
-
@captain spaulding said:
@50ft-trad said:
Cap'n, the knives on at least two (or was it three-I'd need to check) squirts didn't **rub **- they actually got caught up, and there was a flat spot on both knife blades and a mark on the scales from doing this. Have you experienced the (fairly common) saw on a juice getting caught up on an awl, so you have to push the saw over so it closes? Same deal here :-\ Closing the knife without pushing it inwards would get caught up everytime.
On the small tools, it seems the only thing they seem to get consistently right is the pliers. LM always made a good job of pliers - well, until they made the Rebar - not a fan of those at all as I've said many times. I don't have much faith in LM's smaller stuff at all. Nice designs, but I just haven't got any confidence in them.
I know exactly what you mean about the Juice saw.
I'm not saying your right or wrong in any way. I'm just saying I have not had those bad experiences with the PS, Micra, and Squirt line.
Yeah, for sure
All we can do is relay our experiences. Mine have been bad, yours have been good 
-
@jeremy1517 said:
I don't have a pocket clip for the wave yet. I thought I'd like to try something smaller and lighter than the wave.I almost never carry tools in my pocket, but I've been doing a bunch of home repair stuff and have been pocket carrying my Wave. It is unpleasantly heavy, IMO, so I know where you're coming from. Although, the pocket clip DOES work well, and allows the tool to ride deep in the pocket.
-
A Squirt P4 is my EDC - small and light enough I hardly notice it in my pocket, and zero QC issues. I can't say the same about the PS4 version, I have several of these with a broken scissors spring.
-
@50ft-trad said:
@captain spaulding said:
@50ft-trad said:
Cap'n, the knives on at least two (or was it three-I'd need to check) squirts didn't **rub **- they actually got caught up, and there was a flat spot on both knife blades and a mark on the scales from doing this. Have you experienced the (fairly common) saw on a juice getting caught up on an awl, so you have to push the saw over so it closes? Same deal here :-\ Closing the knife without pushing it inwards would get caught up everytime.
On the small tools, it seems the only thing they seem to get consistently right is the pliers. LM always made a good job of pliers - well, until they made the Rebar - not a fan of those at all as I've said many times. I don't have much faith in LM's smaller stuff at all. Nice designs, but I just haven't got any confidence in them.
I know exactly what you mean about the Juice saw.
I'm not saying your right or wrong in any way. I'm just saying I have not had those bad experiences with the PS, Micra, and Squirt line.
Yeah, for sure
All we can do is relay our experiences. Mine have been bad, yours have been good 
Maybe your just a dodgy LM magnet?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login