Any Jeepers out there?
-
I ran the power wire for my OBA kit that I'm going to be installing. I had planned on running 4 gauge power wire, but I ended up running 1 gauge.
I actually still need to zip tie the power wire in place and make it a little neater. Also, the fuse holder is only meant for 4 gauge wire, so I had to use my step drill bit to open the end up so I could get the wire though, and I needed to trim some of the wire so I could fit it into the connector.

Running through the biggest grommet in the firewall on the drivers side.

I used my step drill bit to drill a hole in the rear seat support.

The relay wired and installed.

Once my Viair kit and power distribution block arrives, I'll be able to finish the install.
-
-
Wow, I like.

-
Thanks!

I'm not 100% happy with how the wiring looks though, so might mess around with it a bit more.
-
Looks pottery darned good to me. How loud is the compressor?
Def
Sent from a digital multitool
-
That's good. I was always worried about how loud a compressor was going to be in an enclosed space like the inside of a truck.
Def
Sent from my smurfing hunk of techno sorcery
-
That looks good!
Nate
-
@ducttapetech said:
That looks good!Nate
Thanks! The rest of the bits should be here tomorrow, so I'll be able to finish it all up.
-
-
Looks like a 1990 mitsubishi pajero from the front and sides and a Nissan Quasqai (?) from the back.
Still, a different, new model.



-
Hey Derek, have you done anything to your motor or are you just running the 4.7 stock?
-
@Higgins617 said:
Hey Derek, have you done anything to your motor or are you just running the 4.7 stock?Other than a K&N cone filter and custom heat shield enclosure, it's stock.
-
Hey Derek, have you done anything to your motor or are you just running the 4.7 stock?
Other than a K&N cone filter and custom heat shield enclosure, it's stock.
Is the cone filter just on the stock intake tubes? I'd like a little more kick out of mine, I figure letting her breathe certainly isn't a bad plan.
-
@Higgins617 said:
Is the cone filter just on the stock intake tubes? I'd like a little more kick out of mine, I figure letting her breathe certainly isn't a bad plan.No, I used 3" ABS from the throttle body. I don't have any pics of the whole thing, but this shows the custom heat shield. This one is meant to be a prototype for me to make a better one, but knowing me, this will be on for a while!!
The stock cool air pipe is plumbed in, and the filter and surrounding area do stay cool.I did improve the fitment of the top cover some too since taking those pics.
-
I should also say that it does feel like it responds quicker, and definitely sounds better!
Sent from my Nokia Lumia 1020 using Tapatalk -
Okay that's what I was looking for. It definitely isn't a slouch but I just wish it had better pick up sometimes. I gotta say though, I had to pull our rather heavy boat out of the lake on nothing but wet sand as the owner won't make a ramp, and it did not spin the tires an inch. Pulled like there was nothing behind it at all. But who doesn't want more power
-
Tonka makes cute offroad stuff:
-
Well my wife gave me an early Christmas present today. A dash cam!
Here's a very boring video of me going to get a coffee to test it out.I'm not sure if it's Windows Movie Maker, or Youtube, but the quality is better on my PC.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login






