The Hacked Leatherman Owners Club.
-
-
Nice.

And welcome to the forum if I haven't said that already.

-
You made a Leatherman looks like a Gerber, it is a crime!
LOL well done and welcome.
-
Congrats, that didn't take long. :D Fancy grips you got there.

-
Hardest part was talking the Rebar apart. A bit fiddly getting the tools back in but holding the handle of the multi in my vice helped to steady things. Could do with a second security torx bit, though the wingman screws work OK.
The Irwin pliers are lovely - I've got a pair of side cutters with the same handles too - got a good deal on a set from my local tool shop.
-
@hiraethus said:
Hardest part was talking the Rebar apart. A bit fiddly getting the tools back in but holding the handle of the multi in my vice helped to steady things. Could do with a second security torx bit, though the wingman screws work OK.The Irwin pliers are lovely - I've got a pair of side cutters with the same handles too - got a good deal on a set from my local tool shop.
No, the black and gold. ;)
-
Ah, those! Just a cheapo mole grip knock off, £7 from Halfords (a car/bike/camping spares chain in the UK).

-
Better:

Swapped the large flat driver for one from a Wingman as it's slightly thinner and fitted better, shuffled the tools around, replaced one of the pivots with one from a Kick so I can use a pocket clip and screwed it all back together.Need to make the locking groove on the Wingman flat driver deeper so it locks better and grind some of the tab by the nail nick off to get it flush with the other tools. I also need to swap the position of the can opener and large flat driver as at the moment the can opener pokes through the slots in the handle when you close it up.
-
Don't forget the deploy a tool close the pliers and see if it jams test. :D
-
Wanted to add the Wingman pocket clip - needed to use the Wingman pivots for the hex for the clip to fit over. But they're different sizes - the Wingman plier pivots are smaller than the Rebar. So I made a brass bush from some 0.4mm sheet to line the Rebar pliers hole:

The holes in the handles are too big so there's a bit of play in the handles - I'm going to make some new pivots from 1/4" brass hex bar when I get a chance. Means I can put metric fasteners in instead of the imperial ones in there at the momenet.Had to cut a hole in the handle for the tip of the anti-rotation lug to fit into, but it's lovely and secure now.

Ground a bit more off the Wingman flat driver too, so it clears the lock tab spring better.

-
wow, really nicely done, hiraethus! :o
just yesterday I was eyeballing the Wingman pocket clip to see if I could get it to fit on a Rebar, but I gave up much sooner than you did, apparently. :D I really like the way that clip sits on there.

-
That is looking real nice.
Do you have a pic of the hole you cut? -
@Breezy12 said:
wow, really nicely done, hiraethus! :ojust yesterday I was eyeballing the Wingman pocket clip to see if I could get it to fit on a Rebar, but I gave up much sooner than you did, apparently. :D I really like the way that clip sits on there.

Thanks. I wasn't sure how far I was going to have to go to make this work, but having realised I'd dismantled 4 perfectly functioning multi tools for parts I thought 'smurf it, let's see where this takes me'. :D
@zoidberg said:
That is looking real nice.
Do you have a pic of the hole you cut?I'll take one tomorrow for you. I had to mod the clip too so I'll try to get a shot of that as well.
-
wow, really nicely done, hiraethus! :o
just yesterday I was eyeballing the Wingman pocket clip to see if I could get it to fit on a Rebar, but I gave up much sooner than you did, apparently. :D I really like the way that clip sits on there.

Thanks. I wasn't sure how far I was going to have to go to make this work, but having realised I'd dismantled 4 perfectly functioning multi tools for parts I thought 'smurf it, let's see where this takes me'. :D
@zoidberg said:
That is looking real nice.
Do you have a pic of the hole you cut?I'll take one tomorrow for you. I had to mod the clip too so I'll try to get a shot of that as well.
Cheers. Does it sit good in the pocket?
-
@hiraethus said:
Wanted to add the Wingman pocket clip - needed to use the Wingman pivots for the hex for the clip to fit over. But they're different sizes - the Wingman plier pivots are smaller than the Rebar. So I made a brass bush from some 0.4mm sheet to line the Rebar pliers hole:

The holes in the handles are too big so there's a bit of play in the handles - I'm going to make some new pivots from 1/4" brass hex bar when I get a chance. Means I can put metric fasteners in instead of the imperial ones in there at the momenet.This means I'll have to drill out the Wingman pliers to get them into the Rebar handles. :(
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login








