The Hacked Leatherman Owners Club.
-
Ah, those! Just a cheapo mole grip knock off, £7 from Halfords (a car/bike/camping spares chain in the UK).

-
Better:

Swapped the large flat driver for one from a Wingman as it's slightly thinner and fitted better, shuffled the tools around, replaced one of the pivots with one from a Kick so I can use a pocket clip and screwed it all back together.Need to make the locking groove on the Wingman flat driver deeper so it locks better and grind some of the tab by the nail nick off to get it flush with the other tools. I also need to swap the position of the can opener and large flat driver as at the moment the can opener pokes through the slots in the handle when you close it up.
-
Don't forget the deploy a tool close the pliers and see if it jams test. :D
-
Wanted to add the Wingman pocket clip - needed to use the Wingman pivots for the hex for the clip to fit over. But they're different sizes - the Wingman plier pivots are smaller than the Rebar. So I made a brass bush from some 0.4mm sheet to line the Rebar pliers hole:

The holes in the handles are too big so there's a bit of play in the handles - I'm going to make some new pivots from 1/4" brass hex bar when I get a chance. Means I can put metric fasteners in instead of the imperial ones in there at the momenet.Had to cut a hole in the handle for the tip of the anti-rotation lug to fit into, but it's lovely and secure now.

Ground a bit more off the Wingman flat driver too, so it clears the lock tab spring better.

-
wow, really nicely done, hiraethus! :o
just yesterday I was eyeballing the Wingman pocket clip to see if I could get it to fit on a Rebar, but I gave up much sooner than you did, apparently. :D I really like the way that clip sits on there.

-
That is looking real nice.
Do you have a pic of the hole you cut? -
@Breezy12 said:
wow, really nicely done, hiraethus! :ojust yesterday I was eyeballing the Wingman pocket clip to see if I could get it to fit on a Rebar, but I gave up much sooner than you did, apparently. :D I really like the way that clip sits on there.

Thanks. I wasn't sure how far I was going to have to go to make this work, but having realised I'd dismantled 4 perfectly functioning multi tools for parts I thought 'smurf it, let's see where this takes me'. :D
@zoidberg said:
That is looking real nice.
Do you have a pic of the hole you cut?I'll take one tomorrow for you. I had to mod the clip too so I'll try to get a shot of that as well.
-
wow, really nicely done, hiraethus! :o
just yesterday I was eyeballing the Wingman pocket clip to see if I could get it to fit on a Rebar, but I gave up much sooner than you did, apparently. :D I really like the way that clip sits on there.

Thanks. I wasn't sure how far I was going to have to go to make this work, but having realised I'd dismantled 4 perfectly functioning multi tools for parts I thought 'smurf it, let's see where this takes me'. :D
@zoidberg said:
That is looking real nice.
Do you have a pic of the hole you cut?I'll take one tomorrow for you. I had to mod the clip too so I'll try to get a shot of that as well.
Cheers. Does it sit good in the pocket?
-
@hiraethus said:
Wanted to add the Wingman pocket clip - needed to use the Wingman pivots for the hex for the clip to fit over. But they're different sizes - the Wingman plier pivots are smaller than the Rebar. So I made a brass bush from some 0.4mm sheet to line the Rebar pliers hole:

The holes in the handles are too big so there's a bit of play in the handles - I'm going to make some new pivots from 1/4" brass hex bar when I get a chance. Means I can put metric fasteners in instead of the imperial ones in there at the momenet.This means I'll have to drill out the Wingman pliers to get them into the Rebar handles. :(
-
Closeups of the installed clip:


I used a couple of spacers from the Wingman as the pivot is longer than it needed to be. I'll make the new one shorter to suit.The hole is a bit ragged as I kept slipping with the tiny diamond burrs on my dremel on the angled face I was cutting into - needs more work with the diamond files.


@zoidberg said:
This means I'll have to drill out the Wingman pliers to get them into the Rebar handles. :(Or, if you've access to a lathe, turn some stepped collars to locate the smaller diameter pivots in the large holes in the handles.
-
Hi guys, I love going thru this thread. Lots of ideas. I have a rebar that I bought for the pliers and a new charge tti that I wanted to put them in. After doing the swap I ended up changing them back the way they were. The pliers weren't perfect and the blades wouldn't unlock. I think I'd rather get a charge bit holder for the rebar but I'm not willing to sacrifice the one of my charge lol. Where can I get one cheap (if there is a way)?
-
@pdrift86 said:
Hi guys, I love going thru this thread. Lots of ideas. I have a rebar that I bought for the pliers and a new charge tti that I wanted to put them in. After doing the swap I ended up changing them back the way they were. The pliers weren't perfect and the blades wouldn't unlock. I think I'd rather get a charge bit holder for the rebar but I'm not willing to sacrifice the one of my charge lol. Where can I get one cheap (if there is a way)?sounds like you encountered the overextended pin issue that some of us have run into. ;) are you saying that when the tool was closed, the blades wouldn't open properly? the pin on the safety lock sometimes overextends with the Rebar pliers in there, but you can either grind down the pins to allow clearance or just remove the pin mechanism altogether.
-
Yes, that's exactly what happened. I didn't want to grind it though since I just got it back from warranty.. It's brand new and I didn't want to mess anything up. lol.
-
Think I'll finally enter this one with my latest mod: The SurCharge
-
@Toolslinger said:
Think I'll finally enter this one with my latest mod: The SurChargeWe need the pics here!

-
Think I'll finally enter this one with my latest mod: The SurCharge
We need the pics here!

Well then :P
Here you go...
-
Thats much better.

-
Here's the updated SurCharge with it's companion tools.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


