Introducing: Toolslinger's SurCharge
-
Now, I'm no stranger to modding and customizing things. Been doing it since before I knew what it meant. That being said, most of the things I mod are done for personal use and tend to never be displayed or shown off. This time, I decided I should post some pics and brief write up of my latest Leatherman modification.
So without further ado, I give you the SurCharge!
But you can just call him Sir. ;)This is my take on the ReCharge and Mini Surge.
First, why did I do this? Well, I had been itching for a Charge XTi and I wanted to go full pocket carry with minimal extras. I like the Wave, but I like the Titanium Charges more as my very first LM was a Charge XTi. Love that tool and still own it (retired as a shelf Queen). The new Surge was just too darned big and needed tons of accessories to work right. So, it made sense to combine the best of all worlds (for me, YMMV).
I started with a new model Charge TTi and stripped it down. I removed the blade locks as they would interfere with interior and exterior tool loads. I went so far as to completely remove the mechanism (not just snapping off the excess) and added a new rivet to tighten up the locks.
I then proceeded to steal an extra large bit driver from a parts/beater Wave, a Rebar plier head and the Scissors from my friends Wingman (the only tool on it he doesn't use).
I had to do some minor grinding (with a small, round hand file) to enlarge the pivot on the scissors to fit the Charge plier pivots. Taking it slow and checking progress often is key. After getting the pivot enlarged, minor stock removal on the lock face was required to get it to snap into place and lock up solidly. Again, slow and steady, check often.
After getting the scissors to lock up, I rebuilt the plier end of the tool. I ditched the serrated gut hook blade and placed the saw in it's place. This gave me saw, file, S30V PE blade and scissors all accessible from the outside. The Rebar plier head dropped in with no mods as expected.
The only modification I had to make to the saw, was to remove a tiny bit of metal on the lock face to get it to lock up. The detent doesn't matter on this tool as the scale and pivot tension is more than adequate to hold it in the tool yet still allow for easy deployment with the friction of my thumb pad. I had to add some extra bronze washers (total of 3 on scale side and 2 on frame side) to get it to fit space-wise with the Charge scales.
Moving on to the lower end of the tool, I ditched the hidden lanyard loop to allow for a pair of tweezers to slide in to the butt of the handle or to hold the mini driver should I choose. I went with a Charge XTi load-out with the only tweak being to replace the small bit driver with the long narrow flat driver from the ReBar. All in all, I had two large bit drivers, the long flat driver and the can-opener/multi-use tool.
Add the pocket clip and adjust pivot tension and voila! the SurCharge is born.
Here is how I look at it from a tool perspective.
Tools:
Pliers with replaceable cutters and crimper - the best LM plier head for a 4" tool. The cutters are amazing and the pliers functional superbly for my needs.
PE blade - S30V and OHO means I don't carry a dedicated folder. I like this as it's one less thing to carry and with it clipped in my front pocket, it's basically a multi-use folder anyway.
Saw - comes in handy occasionally and is a nice to have. I took it over the serrated blade to show it could be done and because I rarely ever use the serrated blade.
File - must have on any tool load I carry. I love the versatility of the diamond/wood metal combo. I can clean up fingernails with one side and deburr metal with the other. Why not detachable like the mini-surge? I prefer to have it in the tool and have never needed it to touch up a blade where being detached would help. I usually have access to something on which I can sharpen my blades or am not far from somewhere that does. Considering how often I've needed to sharpen in the field (hint: zero) having it attached means I'm less likely to lose or forget it.
Scissors: another must have tool for me. Precision cutting, people friendly and versatile.
Dual bit drivers: This means that I can carry my two most common bits (Robertson 1/2 and Philips 1/2) and still have my most commonly needed flat driver. No extra bits in pocket. The only other one I would carry is the 4mm/5mm hex for adjusting IKEA type furniture and I'd carry it installed in the driver extension and dropped in a pocket. Now I don't need a sheath or bit card.
Long flat driver: my most used flat driver size and it has reach. Much more useful than a small bit driver to me.
Can open/multi-use tool: lots I can do with this and I happen to prefer the can opener to the Vic one (I know, blasphemy right?). The wire stripper notch has multiple uses and by slightly sharpening the hook, I can cut things with it.Now, I know you're probably wondering where my Awl is at. I can count on one hand the number of times I've needed an Awl and still have all 5 fingers left. So it was a no brainer to leave out. Plus I would have had to do a lot of grinding to get it to fit with two bit drivers. Just wasn't interested.
-
Great!

-
You can always sharpen the can opner a bit to use as box opener and awl.
-
That's really nice
I would love for my ReCharge TTi to have scissors on the outside like that. I would probably put them in place of the serrated blade though. I guess I'd just put an awl in place of the regular Charge scissors inside. Not really sure what else would work there
Well, maybe ditch the bit driver and replace it with a regular phillips, and put a small/medium sized flathead in place of the scissors. Oh man, now I've got ideas >:D -
Nice mod!!!
Nate
-
nice work, Toolslinger!
love the name for it, too. ;) -
Very nice.

-
@Monrogue said:
That's really nice
I would love for my ReCharge TTi to have scissors on the outside like that. I would probably put them in place of the serrated blade though. I guess I'd just put an awl in place of the regular Charge scissors inside. Not really sure what else would work there
Well, maybe ditch the bit driver and replace it with a regular phillips, and put a small/medium sized flathead in place of the scissors. Oh man, now I've got ideas >:DThe way the Wingman scissors are constructed (lever layer) would limit them to being placed in the file or saw slots. If you want to keep file and saw, it's fairly easy to swap one of them into the knife slot like I did. Vic scissors might work but I'm not sure of their thickness relative to the blade...
-
That's really nice
I would love for my ReCharge TTi to have scissors on the outside like that. I would probably put them in place of the serrated blade though. I guess I'd just put an awl in place of the regular Charge scissors inside. Not really sure what else would work there
Well, maybe ditch the bit driver and replace it with a regular phillips, and put a small/medium sized flathead in place of the scissors. Oh man, now I've got ideas >:DThe way the Wingman scissors are constructed (lever layer) would limit them to being placed in the file or saw slots. If you want to keep file and saw, it's fairly easy to swap one of them into the knife slot like I did. Vic scissors might work but I'm not sure of their thickness relative to the blade...
Ah, thanks for the info man
I would likely just have one of them put in the serrated blade's spot then. -
Well done and hats off to you for putting a great tool together.
-
Very nice!!
Sent from my iPad using Tapatalk
-
Very nice job there buddy.

I would love to upgrade to those newer handle slabs, they look mint. :)
So can I have the serrated gut hook blade?

-
Sweet name and great load out. I'm really like that name

-
@Toolslinger said:
Thanks everyone for all the props! Gotta love this place.@zoidberg I'm keeping the blade ;) probably gonna swap it back in place of the saw. I can get a nice 111mm SAK with awl and saw, but I'm not a big fan of serrated Vic blades (plus no guthook).
Yeah the gut hook rules.

-
Thanks everyone for all the props! Gotta love this place.
@zoidberg I'm keeping the blade ;) probably gonna swap it back in place of the saw. I can get a nice 111mm SAK with awl and saw, but I'm not a big fan of serrated Vic blades (plus no guthook).
Yeah the gut hook rules.

I asked him about it too via PM. ;) those blades are great, they're just hard to come by.
-
Thanks everyone for all the props! Gotta love this place.
@zoidberg I'm keeping the blade ;) probably gonna swap it back in place of the saw. I can get a nice 111mm SAK with awl and saw, but I'm not a big fan of serrated Vic blades (plus no guthook).
Yeah the gut hook rules.

I asked him about it too via PM. ;) those blades are great, they're just hard to come by.
Great minds think alike eh. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login