Emerson Multitasker EDC-2
-
I've been testing one for the last several weeks, including sharing it with local fire department, local search and rescue, and at this moment with some folks at SOCOM in Florida. We've been comparing it to the Multitasker 3, plus a whole variety of the usual multitools, rescue tools, etc.
This was designed in partnership with Emerson, and shows the heritage. The focus is on ease of use, almost to the instinctual level. You have to think when digging into a Charge TTi, but with this one, you have just the key basic tools that make or break a situation. Multitasker and Emerson made the decision not to include pliers, which in turn made the tool much smaller and made it possible to make it much faster to pull out and use.
Basic idea? Most of the time what you need -- really need -- isn't scissors or odd screwdriver bits or specialty saws or whatever. You basically just need to cut, to dig a hole you can put a screw into, and then to screw the fastener in. If you have a tool, gun or otherwise, that needs a screw removed, it's usually a slot or philips -- yes, there are torx increasingly around, but when you do torx you also need to do security torx, and then Posidrive, and then square drive, and then a bunch of hex sizes, and on and on. If I have that problem, it's not what i'm pulling a multitool out for. I handle it with a Wera bit kit that has about 60 bits of almost any conceivable type, plus a small screwdriver holder plus a small 4" Snapon ratchet with a 1/4" hex bit to hold the bits. Sometimes I have to do things as odd as take apart a restroom stall because there's a suspected IED or because we're testing for infectious agents -- we could always use a pry bar, but until you already have bombs going off, pry bars really irritate the owners of the building.
Anyway, back to the tool. I want to pull a tool out one handed, flip out a blade without looking, know it's going to lock open, and know it has very good steel. I don't want S30V because I abuse the blade and that's a steel that holds an edge in moderate use but doesn't resharpen easily. The Multitasker strategy has always been to ignore the BS about which is the blade steel du jour, and just go for the steel that works best (the Multitasker 3 uses D2, which gives a fabulous edge and magnificent resharpening, but needs just a modicum of care so it doesn't develop any corrosion). I like this approach. On the Multitasker 2, you have a very resilient but also very re-sharpenable stainless that's really made with the hope that you'll abuse it. Same for the screwdrivers and awl on this tool -- also very tough, sharp, and resharpenable. Everything is locking. Everything opens and locks and then unlocks the same way so you don't have to remember or look. You don't have a lot of other stuff in the way. It just takes a real world view of what you need in a jam, and doesn't try to clutter it up with stuff that gets in the way most of the time. (Ever really work with a MUT or MUT EOD? Unless you use it every day some of the tools are really hard to get at, and several involve moving small pieces back and forth -- in short, it's good for use at a workbench but not in your hands in a hole in the sand. That's the error that Multitasker was trying not to repeat.)
The 2 is a pretty good execution of the concept. It's not for the Charge TTi or Victorinox RS crowd who want so many tools. It does great for what most people really need, especially those who are deep in goo and really have to trust the tool. I'd also point out that it doesn't pack tools so tight that they jam or can't be cleaned -- I've seen a lot of multitools that get jammed up with grit, blood, whatever, so they stop working; if you look at the really successful knives for serious military use, such as the Spyderco paramilitary and military series, they are made with lots of room to clean inside the frame and to allow the blade to close even if the frame is full of muck. Well, same thing here.
The scales are first rate and nicely proportioned and textured to the need at hand. Edges are smooth so the tool can really be used in your hands for a lot of twisting motion (think knife, awl, and screwdrivers, and they are all about twisting motions with your hand). The assembly is with basic bolts -- no security torx or such things that make field stripping more difficult. The tool is also light -- easy to drop in your pocket or clip on a waistband or pocket. I'm left handed and I have no problems using it with either hand -- it's not like some multitools that are very "handed" in their design. Because of the work I do, I wish it was available with fluorescent orange or lime scales -- I have a pair of trauma scissors with fluorescent glow-in-the-dark pink liners that mean I never lose them in the dark, and I'd like every tool to have this option.
I was recently evaluating some new medical technologies during a SERE training session for DevGru at Captiva Island, and decided I'd carry only this tool. As soon as you're on your own and not surrounded by urban fixtures, everything else on a multitool becomes largely irrelevant. This tool let me get into medical electronics equipment, take apart an outboard motor enough to fix an electrical problem, and to work with a dozen medics and helo pilots. The tool got handed around and I wish I had a few to leave behind. These people prize simplicity and functionality. They aren't like the green recruit heading to Afghanistan who buys the biggest Leatherman he can find -- they know they have just a few real needs and they liked this tool.
The tool could be upgraded in a few ways. I'd rather have the flat-bladed screwdriver and then have a hex socket to take any hex bit (I'd carry it with a standard Ph #2). I'd love a small secondary blade, non serrated, that I could save for trimming broken fingernails, blisters, etc. I'd bevel and sharpen the edge of the screwdriver blade so it could open cardboard boxes -- I actually did this myself because half of working an op is opening endless numbers of cardboard boxes, and that's a lousy way to dull a decent blade. I'd like a big lanyard hole, or a permanent tab coming out of the frame to hold a lanyard -- again, that's how I use it. (Pocket clips are nice but sometimes you don't have a good pocket or you have a long heavy coat in the way of your pockets, but your neck is always available to hang a tool from. I'd like an area on the outside where I can use a Sharpie to permanently mark my knife -- I've lost more than a few Leathermen because of that shortcoming. When I'm wearing nomex tactical gloves I can still open the main blade (how many multitools can say that????) but I can't do that for the screwdrivers; I'm not sure I want the same big opening fang on the screwdrivers that I have on the knife blade, but it might be nice. I've also been working around human skin and around inflatable boats, and I'm tempted to blunt the end of the knife blade -- would be nice if I had this option.
All in all, I have fewer complaints about this tool than I have about any other multitool. It's not the tool I leave in the console of my pickup, but that's not what I want when I'm somewhere in the field and I have simple but very critical needs. Open the blade (at a minimum with tactical nomex gloves), a good awl, a couple good basic screwdrivers, the couple small mods I described above, steels that I can abuse at will and then resharpen or reshape after I've been sawing on a line on the deck of a helo. It's a good tool. I'm waiting for Multitasker to come out with their next tool. If you don't like the -2, check out the -3 -- it's the best AR tool in the market and a magnificent full-function multitool. All the tools from Multitasker are made without regard to cost -- they go for the best materials and best manufacturing techniques, and you pay for those. But I know I'll never see one break.
-
Hmm according to the Emerson Website
The tool is 10 x 5 x 5 cm and weights 450 gramms :o
So let me also add this

Because those on the Emerson Website are tiny and of poor quality.@lanedecamp
Bold move dissing MTs and MT-users on MT.O. Especially since your monologue sounded like a sales pitch to me. I also think its the wrong comparison, it should rather be compared to a 93mm SAK.
There is actually only one thing that you pointed out, that is interesting. The fact that you can take the EDC-2 appart for cleaning, care to share a picture of that? -
I am not sure where you see the benefit of the Multitasker-2 over a SI SAK or the new 111mm Soldier?
They deliver blade, screwdrivers, awl in a much lighter and cheaper version. Plus you don't have to worry about corrosion! ;) -
I love to get one of these. All locking tools and blades. Its just the price........
live from Nate's mobile
-
I mean no offense but I was reminded of the "legend of the mall ninja" within the first sentence and certainly when I finished reading. Anyone else

I'd like one also but the price :o
-
The EDC-2 reminds me of my Leatherman Crater knife/screwdriver tool but with some additional, worthy features. I am left handed and the right handed design features of such tools don't work that well for me.
Edited to add:
There is merit in a tool with a great locking blade in combination with locking screwdrivers. If there existed left handed versions of such tools, I would be apt to carry one along with a Knipex pliers instead of an integrated multitool or conventional SAK. -
Newly posted review of the Emerson Multitasker EDC-2:
-
anyone here bought one yet? It is a tactical Pioneer
-
The things a brick.
-
@lanedecamp said:
Multitasker and Emerson made the decision not to include pliers, which in turn made the tool much smaller and made it possible to make it much faster to pull out and use.Basic idea? Most of the time what you need -- really need -- isn't scissors or odd screwdriver bits or specialty saws or whatever. You basically just need to cut, to dig a hole you can put a screw into, and then to screw the fastener in.
I suspect more than a few people might feel the need for pliers to grip, pull, loosen/ tighten nuts/bolts, or cut wire, but if you're happy without pliers I'm not going to say your opinion is wrong - for you
That last rider is very important, as what suits you perfectly may have shortcomings for someone else. It's good to have a choice, so every one can choose what suits their individual needs best.
-
I am not sure where you see the benefit of the Multitasker-2 over a SI SAK or the new 111mm Soldier?
They deliver blade, screwdrivers, awl in a much lighter and cheaper version. Plus you don't have to worry about corrosion! ;)This EDC-2 has a locking awl which is important if you don't want it to fold up on you when you bear down on it such as when making a belt hole in tough leather. This happened to me yesterday with a SAK awl that didn't lock.
-
@lanedecamp said:
I've been testing one for the last several weeks, including sharing it with local fire department, local search and rescue, and at this moment with some folks at SOCOM in Florida. We've been comparing it to the Multitasker 3, plus a whole variety of the usual multitools, rescue tools, etc.This was designed in partnership with Emerson, and shows the heritage. The focus is on ease of use, almost to the instinctual level. You have to think when digging into a Charge TTi, but with this one, you have just the key basic tools that make or break a situation.......................All the tools from Multitasker are made without regard to cost -- they go for the best materials and best manufacturing techniques, and you pay for those. But I know I'll never see one break.
Well, lanedecamp, I want to thank you for taking the time to write your review. I am somewhat surprised that so many readers seem negatively disposed to both the tool, and also critical of your review.
Remember that your opinions remain just that, as do theirs. However, at least you have used the tool seemingly quite extensively, whereas the critics seem to be pontificating from a position of zero everyday-for-them experience. That speaks volumes.
As for the somewhat typical knee-jerk "this thread is useless without pictures" response, there's google, and it's easy to use. Brings up far more pics than anyone needs in less than a second. -
i would not consider the can opener on Pioneer as a + driver.
-
I agree that the most important point is if a tool works for you in the situation you are in.
Apart from that part of the discussion, does anyone own a Multitasker EDC/EDC 2 and can show some comparison pics with some of the usual suspects? (93 mm SAK, 111 mm, Wave...)?I can imagine the quality is good, my brother owns some Emerson fixed blades that are made very well.
-
I wish a few things were different on the tool, but am definitely drawn to it and would carry one. I wish the steel choice was better. I would be good with 154cm. I'm alright with the 440c, but not at the price point. If this was a $50 knife I would not mind the 440 at all. I hate the blade shape. Just personal preference. I like the tool selection and the reach in the drivers. I also like the locking half stop. If I could find one for a decent price I would definitely give it a go.
-
I like the idea of this tool, but can never warm up to the recurve of a short blade(I know it's Emerson, but still...)
I think the 'hurdle' of this product is probably pricing. When compared to most similar Vic or Wenger products, it has the advantage of locking tools and better scales. But whether those extra features and the brand are worthy of almost two Swisschamp, that will largely depends on the buyer.
-
I'm probably one of the few people who doesn't mind the bladeshape at all. But the price point is very off putting
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login