The Hacked Leatherman Owners Club.
-
[quote author=zoidberg link=topic=51510.msg963821#msg963821 date=1413280063]
Do you think the Blade Exchanger would fit? Maybe ditch the opener and fit full length bosch blades?No, i don´t think it would fit. I just got my caliper and measured them, the thickness of the OHTs saw is 2,34 mm (pivot area), and the Surge blade exchanger has 3,6 mm (also measured the Gerber/Remgrit, it´s 4,68 mm). No fit, unless you make a complete new pivot post, and even then i´m afraid it will not work as smooth as now and the scales would be twisted from one end to the other.
Additional - it´s hard to get a BO Wave saw, i only can assume how much harder it might be to find a BO Surge blade exchanger.
If i would have a spare one, i definately would try to make it fit. :D A few days ago i was working on the electrics in my new workshop, installing the lines for the 3phase 400V system. I did that "on wall" using plastic tubes, and when i had to cut them to length i noticed i had lost my small metal-hacksaw somewhere between stuff. Instead of starting a long search i used the Surge on my belt - and the woodsaw blade worked for the thinwalled plastic tube, but not that great. Swapped it out with the metal blade from the sheath, and it worked like a charme. The exchanger is the best saw solution i know.
I don't have a surge YET...... come on christmas :D but out of curiosity, would it be possible to replace one of the inside accessible tools with a saw off a blast, then keep the file on the exchanger?
-
@zoidberg said:
What if you removed the extra spring to make the blade exchanger thinner?If you´re talking regarding the spring that goes through the hole - it´s so thin, it makes no real difference. If there will be found a way to fit the exchanger without it, i´m sure it could be done with it, too.
-
@JBW1 said:
I don't have a surge YET...... come on christmas :D but out of curiosity, would it be possible to replace one of the inside accessible tools with a saw off a blast, then keep the file on the exchanger?Nar, the pivot area is larger on the Surge and the pliers block the use of longer tools.
-
@JBW1 said:
I don't have a surge YET...... come on christmas :D but out of curiosity, would it be possible to replace one of the inside accessible tools with a saw off a blast, then keep the file on the exchanger?Just grabbed my Blast to have a look - no i don´t think the saw will fit inside the Surge.
The following is just by the look, i havn´t disassembled and measured them to check it.
- The Blasts pivot area looks smaller, so probably the saw wouldn´t lock (or at least not good).
- Without disassembling no statement to the dia of the pivot posts.
- And the final dealbreaker ... it seems the plierhead of the Surge needs all the free space inside the folded handles, so i assume the long saw would take that space and the tool will not fold (completely) anymore.
-
What if you removed the extra spring to make the blade exchanger thinner?
If you´re talking regarding the spring that goes through the hole - it´s so thin, it makes no real difference. If there will be found a way to fit the exchanger without it, i´m sure it could be done with it, too.
I don't have an OHT yet so I can't see what there is to work with.
However I do have a BO Surge. If you can see it working let me know. I just may send you the part.
-
Arrrrrrg!?! ok cool thanks for looking into it guys. I don't like to carry a sheath, so all this got me thinking of the, hopefully near, future of being a surge owner
-
@zoidberg said:
I don't have an OHT yet so I can't see what there is to work with.However I do have a BO Surge. If you can see it working let me know. I just may send you the part.
I have both - but these 2 are the ones i edc, so i can´t disassemble both at the same time. (Since i got used to these 2 big MTs i can´t leave the house with any of the small ones.
) And under line i would still have one without. 
If you want to let yours go, let me know what you want for it - i will try to find a way to implement it to the OHT.
Out of curiosity ... if you take yours out of the Surge, what do you plan to insert as a new tool?
-
-
I don't have an OHT yet so I can't see what there is to work with.
However I do have a BO Surge. If you can see it working let me know. I just may send you the part.
I have both - but these 2 are the ones i edc, so i can´t disassemble both at the same time. (Since i got used to these 2 big MTs i can´t leave the house with any of the small ones.
) And under line i would still have one without. 
If you want to let yours go, let me know what you want for it - i will try to find a way to implement it to the OHT.
Out of curiosity ... if you take yours out of the Surge, what do you plan to insert as a new tool?
I have no idea what I would replace it with. And I don't want to let it go.
But if finding one in BO was the last thing holding you up then I could possibly make the sacrifice.
-
@zoidberg said:
I have no idea what I would replace it with. And I don't want to let it go.But if finding one in BO was the last thing holding you up then I could possibly make the sacrifice.
I always thought about replacing it with a Wave saw - until you mentioned the exchanger a few posts above.

Now it IS the holding factor to find one to try it
- but definately not for the price of you giving up yours while you still want to keep it. No Sir, thanks, but no. 
-
I've been working on a variation of the Mini Surge for a guy who saw the youtube review and contacted me about a custom mod. (thanks Kampfer!)
he wanted the fixed drivers installed instead of the bit drivers, but didn't want the blade lockout springs/pins removed. as a result, there was quite a bit of grinding/reprofiling involved, but I'm pretty happy with how it turned out. (sorry for the crappy, flash-heavy pics.)
Rebar Phillips driver, and I actually had to grind the can opener a bit to get a good fit with the Rebar plier head... never encountered this before. I'm not sure if it has something to do with the newer Wave handles.


Rebar awl and flat drivers on this side. I actually ended up using the small flat driver from a Kick instead of the one from the Rebar. it fit in there very nicely after a little reprofiling.


the finished product:

I also tried Kampfer's file mod with this one. it's not the prettiest job in the world, but it's a nice, snug fit, and it gets the job done. ;)


-
great job! 
-
@Breezy12 said:
I've been working on a variation of the Mini Surge for a guy who saw the youtube review and contacted me about a custom mod. (thanks Kampfer!)Questions. Did you change the pliers at all? Did you remove the plier rests? Does the Wave have the little bumps inside the handle to stop the lock release tabs from being pushed in too far? If yes, were they an issue?
I think it needs the gutting hook. Still, its a wee beastie.

-
I have no idea what I would replace it with. And I don't want to let it go.
But if finding one in BO was the last thing holding you up then I could possibly make the sacrifice.
I always thought about replacing it with a Wave saw - until you mentioned the exchanger a few posts above.

Now it IS the holding factor to find one to try it
- but definately not for the price of you giving up yours while you still want to keep it. No Sir, thanks, but no. 
I just need to know it wouldn't be wasted. Check the bay, PM metro and breezy etc. If no love, its yours. :)
-
@zoidberg said:
I just need to know it wouldn't be wasted. Check the bay, PM metro and breezy etc. If no love, its yours. :)You, Sir, are way to generous.

I could never accept it, and ending with having one in each of my two main tools - and leaving you without the main advantage in your Surge.
But many thanks for putting this bee in my ear :D - i will look out for one to give this mod a try.
-
thanks Kampfer! and thanks again for sending in your Mini Surge for the youtube review.

I've been working on a variation of the Mini Surge for a guy who saw the youtube review and contacted me about a custom mod. (thanks Kampfer!)
Questions. Did you change the pliers at all? Did you remove the plier rests? Does the Wave have the little bumps inside the handle to stop the lock release tabs from being pushed in too far? If yes, were they an issue?
I think it needs the gutting hook. Still, its a wee beastie.

thanks zoidberg.

Nope, no modification to the pliers at all. Grinding/reprofiling was done on the Phillips driver, small flat driver, and awl (and a tiny bit on the can opener) to allow complete closure of the handles.
Yes, the plier rests were removed -- there is NO way you're getting that Phillips driver in there without removing at least one of them. ;)
Yes, the new Wave handles still have those small bumps to stop the lock release tabs, but they didn't present any issues. I put the awl in the scissors spot, and the profile of the awl allows clearance of that bump. Ditto for the curvature of the underside of the Phillips driver.

I completely agree with you about the hook!
but those things are a pain in the ass to track down without disassembling a Charge. I check the TTC ebay page regularly (and grab them when they're available), but they haven't had any in stock for awhile. :( I even sent them an email, but they said they don't have any available at the moment. -
I just need to know it wouldn't be wasted. Check the bay, PM metro and breezy etc. If no love, its yours. :)
You, Sir, are way to generous.

I could never accept it, and ending with having one in each of my two main tools - and leaving you without the main advantage in your Surge.
But many thanks for putting this bee in my ear :D - i will look out for one to give this mod a try.
I don't have one in BO, but I'd be happy to help you track down a donor BO Surge on ebay if you'd like.

-
Arrrrrrg!?! ok cool thanks for looking into it guys. I don't like to carry a sheath, so all this got me thinking of the, hopefully near, future of being a surge owner
I edc the Surge, but with a sheath on my belt. A Surge loose in the pockets .... you must be a braver man than i. :D
Errr just less experienced with the surge. But hopefully not for long. The clip does look dwarfed on it huh?? Well I may have walk a little stiff legged
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
