The Hacked Leatherman Owners Club.
-
Sweet, a skulldriver. :D
-
@ducttapetech said:
Looks good!! Nicely done.Nate
Thanks Nate.
This lifts the "toolability" on a new level (at least for my way of MT use).
-
Serrated blade upgrade ....... done.

Nice one buddy.

Thanks, mate. :D
I wish i could find a matching BO saw as well.
-
Serrated blade upgrade ....... done.

Nice one buddy.

Thanks, mate. :D
I wish i could find a matching BO saw as well.
Do you think the Blade Exchanger would fit? Maybe ditch the opener and fit full length bosch blades?
-
@zoidberg said:
Do you think the Blade Exchanger would fit? Maybe ditch the opener and fit full length bosch blades?No, i don´t think it would fit. I just got my caliper and measured them, the thickness of the OHTs saw is 2,34 mm (pivot area), and the Surge blade exchanger has 3,6 mm (also measured the Gerber/Remgrit, it´s 4,68 mm). No fit, unless you make a complete new pivot post, and even then i´m afraid it will not work as smooth as now and the scales would be twisted from one end to the other.
Additional - it´s hard to get a BO Wave saw, i only can assume how much harder it might be to find a BO Surge blade exchanger.
If i would have a spare one, i definately would try to make it fit. :D A few days ago i was working on the electrics in my new workshop, installing the lines for the 3phase 400V system. I did that "on wall" using plastic tubes, and when i had to cut them to length i noticed i had lost my small metal-hacksaw somewhere between stuff. Instead of starting a long search i used the Surge on my belt - and the woodsaw blade worked for the thinwalled plastic tube, but not that great. Swapped it out with the metal blade from the sheath, and it worked like a charme. The exchanger is the best saw solution i know.
-
Do you think the Blade Exchanger would fit? Maybe ditch the opener and fit full length bosch blades?
No, i don´t think it would fit. I just got my caliper and measured them, the thickness of the OHTs saw is 2,34 mm (pivot area), and the Surge blade exchanger has 3,6 mm (also measured the Gerber/Remgrit, it´s 4,68 mm). No fit, unless you make a complete new pivot post, and even then i´m afraid it will not work as smooth as now and the scales would be twisted from one end to the other.
Additional - it´s hard to get a BO Wave saw, i only can assume how much harder it might be to find a BO Surge blade exchanger.
If i would have a spare one, i definately would try to make it fit. :D A few days ago i was working on the electrics in my new workshop, installing the lines for the 3phase 400V system. I did that "on wall" using plastic tubes, and when i had to cut them to length i noticed i had lost my small metal-hacksaw somewhere between stuff. Instead of starting a long search i used the Surge on my belt - and the woodsaw blade worked for the thinwalled plastic tube, but not that great. Swapped it out with the metal blade from the sheath, and it worked like a charme. The exchanger is the best saw solution i know.
What if you removed the extra spring to make the blade exchanger thinner?
-
[quote author=zoidberg link=topic=51510.msg963821#msg963821 date=1413280063]
Do you think the Blade Exchanger would fit? Maybe ditch the opener and fit full length bosch blades?No, i don´t think it would fit. I just got my caliper and measured them, the thickness of the OHTs saw is 2,34 mm (pivot area), and the Surge blade exchanger has 3,6 mm (also measured the Gerber/Remgrit, it´s 4,68 mm). No fit, unless you make a complete new pivot post, and even then i´m afraid it will not work as smooth as now and the scales would be twisted from one end to the other.
Additional - it´s hard to get a BO Wave saw, i only can assume how much harder it might be to find a BO Surge blade exchanger.
If i would have a spare one, i definately would try to make it fit. :D A few days ago i was working on the electrics in my new workshop, installing the lines for the 3phase 400V system. I did that "on wall" using plastic tubes, and when i had to cut them to length i noticed i had lost my small metal-hacksaw somewhere between stuff. Instead of starting a long search i used the Surge on my belt - and the woodsaw blade worked for the thinwalled plastic tube, but not that great. Swapped it out with the metal blade from the sheath, and it worked like a charme. The exchanger is the best saw solution i know.
I don't have a surge YET...... come on christmas :D but out of curiosity, would it be possible to replace one of the inside accessible tools with a saw off a blast, then keep the file on the exchanger?
-
@zoidberg said:
What if you removed the extra spring to make the blade exchanger thinner?If you´re talking regarding the spring that goes through the hole - it´s so thin, it makes no real difference. If there will be found a way to fit the exchanger without it, i´m sure it could be done with it, too.
-
@JBW1 said:
I don't have a surge YET...... come on christmas :D but out of curiosity, would it be possible to replace one of the inside accessible tools with a saw off a blast, then keep the file on the exchanger?Nar, the pivot area is larger on the Surge and the pliers block the use of longer tools.
-
@JBW1 said:
I don't have a surge YET...... come on christmas :D but out of curiosity, would it be possible to replace one of the inside accessible tools with a saw off a blast, then keep the file on the exchanger?Just grabbed my Blast to have a look - no i don´t think the saw will fit inside the Surge.
The following is just by the look, i havn´t disassembled and measured them to check it.
- The Blasts pivot area looks smaller, so probably the saw wouldn´t lock (or at least not good).
- Without disassembling no statement to the dia of the pivot posts.
- And the final dealbreaker ... it seems the plierhead of the Surge needs all the free space inside the folded handles, so i assume the long saw would take that space and the tool will not fold (completely) anymore.
-
What if you removed the extra spring to make the blade exchanger thinner?
If you´re talking regarding the spring that goes through the hole - it´s so thin, it makes no real difference. If there will be found a way to fit the exchanger without it, i´m sure it could be done with it, too.
I don't have an OHT yet so I can't see what there is to work with.
However I do have a BO Surge. If you can see it working let me know. I just may send you the part.
-
Arrrrrrg!?! ok cool thanks for looking into it guys. I don't like to carry a sheath, so all this got me thinking of the, hopefully near, future of being a surge owner
-
@zoidberg said:
I don't have an OHT yet so I can't see what there is to work with.However I do have a BO Surge. If you can see it working let me know. I just may send you the part.
I have both - but these 2 are the ones i edc, so i can´t disassemble both at the same time. (Since i got used to these 2 big MTs i can´t leave the house with any of the small ones.
) And under line i would still have one without. 
If you want to let yours go, let me know what you want for it - i will try to find a way to implement it to the OHT.
Out of curiosity ... if you take yours out of the Surge, what do you plan to insert as a new tool?
-
-
I don't have an OHT yet so I can't see what there is to work with.
However I do have a BO Surge. If you can see it working let me know. I just may send you the part.
I have both - but these 2 are the ones i edc, so i can´t disassemble both at the same time. (Since i got used to these 2 big MTs i can´t leave the house with any of the small ones.
) And under line i would still have one without. 
If you want to let yours go, let me know what you want for it - i will try to find a way to implement it to the OHT.
Out of curiosity ... if you take yours out of the Surge, what do you plan to insert as a new tool?
I have no idea what I would replace it with. And I don't want to let it go.
But if finding one in BO was the last thing holding you up then I could possibly make the sacrifice.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

