Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

58mm Mod Question

Scheduled Pinned Locked Moved The Mod Squad
11 Posts 1 Posters 1.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. 58mm Mod Question
58mm Mod Question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • neillcurrie Offline
    neillcurrie
    Posts: 860
    neillcurrie Offline
    neillcurrie
    wrote on last edited by neillcurrie
    #1 Quote Reply

      Pretty sure the clip is secured by pins that are further apart on their centers. A ruler will tell you for sure.
      Edit: even if the pins are the correct spacing, wouldn't the clip be too large on the 58mm frame?

      1 Reply Last reply
      • jrp316 Offline
        jrp316
        Posts: 436
        jrp316 Offline
        jrp316
        wrote on last edited by
        #2 Quote Reply

          58mm pins are 1.5mm, while 74mm are 2mm, so there's that to contend with too.

          1 Reply Last reply
          • willfcc Offline
            willfcc
            Posts: 38
            willfcc Offline
            willfcc
            wrote on last edited by
            #3 Quote Reply

              Forgot about the diameter difference, but, perhaps the peening could be generous enough to capture the clip.

              1 Reply Last reply
              • Michel M. Offline
                Michel M.
                Posts: 243
                Michel M. Offline
                Michel M.
                wrote on last edited by
                #4 Quote Reply

                  The pins spacing is not the same. About 7 mm on 58 mm and about 10 mm on 74 mm.

                  1 Reply Last reply
                  • willfcc Offline
                    willfcc
                    Posts: 38
                    willfcc Offline
                    willfcc
                    wrote on last edited by
                    #5 Quote Reply

                      Not going to make that up with peening. Thanks for the answers!

                      1 Reply Last reply
                      • tattoosteve99 Offline
                        tattoosteve99
                        Posts: 6,326
                        tattoosteve99 Offline
                        tattoosteve99
                        wrote on last edited by
                        #6 Quote Reply

                          You could get oversized pin stock then sand down a section to the right size for the 58mm, leaving the correct size for the clip.

                          1 Reply Last reply
                          • rickinFL Offline
                            rickinFL
                            Posts: 941
                            rickinFL Offline
                            rickinFL
                            wrote on last edited by
                            #7 Quote Reply

                              beat brass into the holes and redrill for 1/16

                              1 Reply Last reply
                              • jrp316 Offline
                                jrp316
                                Posts: 436
                                jrp316 Offline
                                jrp316
                                wrote on last edited by
                                #8 Quote Reply

                                  Check this out: </post/895266>

                                  1 Reply Last reply
                                  • bmot Offline
                                    bmot
                                    Posts: 4,468
                                    bmot Offline
                                    bmot
                                    wrote on last edited by
                                    #9 Quote Reply

                                      @jrp316 said:
                                      Check this out: http://forum.multitool.or....msg895266.html#msg895266

                                      Hey, I was just looking for that :P

                                      1 Reply Last reply
                                      • willfcc Offline
                                        willfcc
                                        Posts: 38
                                        willfcc Offline
                                        willfcc
                                        wrote on last edited by willfcc
                                        #10 Quote Reply

                                          Thanks!!!! jrp316. I WILL check that out!
                                          I really like the idea of using the knife as a dangler.

                                          Will

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Tool Talk
                                          3. The Mod Squad
                                          4. 58mm Mod Question
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0