Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

58mm Mod Question

Scheduled Pinned Locked Moved The Mod Squad
11 Posts 1 Posters 1.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. 58mm Mod Question
58mm Mod Question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • willfcc Offline
    willfcc
    Posts: 38
    willfcc Offline
    willfcc
    wrote on last edited by
    Quote Reply

      I'm thinking of doing an Alox Vagabond with some leftover parts, and would like to know if the clip from the 74mm MoneyClip is a direct fit on 58mm Alox pins?

      Will

      1 Reply Last reply
      • neillcurrie Offline
        neillcurrie
        Posts: 860
        neillcurrie Offline
        neillcurrie
        wrote on last edited by neillcurrie
        #1 Quote Reply

          Pretty sure the clip is secured by pins that are further apart on their centers. A ruler will tell you for sure.
          Edit: even if the pins are the correct spacing, wouldn't the clip be too large on the 58mm frame?

          1 Reply Last reply
          • jrp316 Offline
            jrp316
            Posts: 436
            jrp316 Offline
            jrp316
            wrote on last edited by
            #2 Quote Reply

              58mm pins are 1.5mm, while 74mm are 2mm, so there's that to contend with too.

              1 Reply Last reply
              • willfcc Offline
                willfcc
                Posts: 38
                willfcc Offline
                willfcc
                wrote on last edited by
                #3 Quote Reply

                  Forgot about the diameter difference, but, perhaps the peening could be generous enough to capture the clip.

                  1 Reply Last reply
                  • Michel M. Offline
                    Michel M.
                    Posts: 243
                    Michel M. Offline
                    Michel M.
                    wrote on last edited by
                    #4 Quote Reply

                      The pins spacing is not the same. About 7 mm on 58 mm and about 10 mm on 74 mm.

                      1 Reply Last reply
                      • willfcc Offline
                        willfcc
                        Posts: 38
                        willfcc Offline
                        willfcc
                        wrote on last edited by
                        #5 Quote Reply

                          Not going to make that up with peening. Thanks for the answers!

                          1 Reply Last reply
                          • tattoosteve99 Offline
                            tattoosteve99
                            Posts: 6,326
                            tattoosteve99 Offline
                            tattoosteve99
                            wrote on last edited by
                            #6 Quote Reply

                              You could get oversized pin stock then sand down a section to the right size for the 58mm, leaving the correct size for the clip.

                              1 Reply Last reply
                              • rickinFL Offline
                                rickinFL
                                Posts: 941
                                rickinFL Offline
                                rickinFL
                                wrote on last edited by
                                #7 Quote Reply

                                  beat brass into the holes and redrill for 1/16

                                  1 Reply Last reply
                                  • jrp316 Offline
                                    jrp316
                                    Posts: 436
                                    jrp316 Offline
                                    jrp316
                                    wrote on last edited by
                                    #8 Quote Reply

                                      Check this out: </post/895266>

                                      1 Reply Last reply
                                      • bmot Offline
                                        bmot
                                        Posts: 4,468
                                        bmot Offline
                                        bmot
                                        wrote on last edited by
                                        #9 Quote Reply

                                          @jrp316 said:
                                          Check this out: http://forum.multitool.or....msg895266.html#msg895266

                                          Hey, I was just looking for that :P

                                          1 Reply Last reply
                                          • willfcc Offline
                                            willfcc
                                            Posts: 38
                                            willfcc Offline
                                            willfcc
                                            wrote on last edited by willfcc
                                            #10 Quote Reply

                                              Thanks!!!! jrp316. I WILL check that out!
                                              I really like the idea of using the knife as a dangler.

                                              Will

                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              1. Home
                                              2. Tool Talk
                                              3. The Mod Squad
                                              4. 58mm Mod Question
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0