The Hacked Leatherman Owners Club.
-
I have a SAK Alox Classic on my key chain. Small scissors but the are precise and sharp. I cut an occasional thread, hang nail, fingernail, and coupons. I could live without them in my multi-tool though.
-
Regarding the outside - as long as my main need on the Surge (serrated blade, plain blade, sawblade) are covered oho, i don´t care for whats in the fourth slot. But putting the scissors in is not that bad, as it enables big and usefull scissors - small scissors are wasted space for me, no matter if inside or outside.
-
@Lichtbote said:
Regarding the outside - as long as my main need on the Surge (serrated blade, plain blade, sawblade) are covered oho, i don´t care for whats in the fourth slot. But putting the scissors in is not that bad, as it enables big and usefull scissors - small scissors are wasted space for me, no matter if inside or outside.Fan of the saw even though I use it not so much. But do you find yourself using the saw more then a good file? Not this guy.
-
I use both.
-
@hiraethus said:
I had to tickle a tiny bit off one corner of the saw too, so it locked easily when I moved it to the serrated blade slot. The small flat driver is modified too, to clear the lock pivot.Not (yet) a Wave owner but I have a plan for a "Knifeless Wave". Couple of questions. Firstly taking account of length only could a 3D Phillips be made to fit in lieu of the bit holder?
Secondly the saw locking edge would have had the opposite bevel, presumably why it needed a bit of a grind. Once ground did it lock as securely as in the correct bay?
-
@ducttapetech said:
I use both.Yeah the question was which is used the most? Saw or File. My vote was file by a long shot, but again I am in the desert so yeah.
-
I use both.
Yeah the question was which is used the most? Saw or File. My vote was file by a long shot, but again I am in the desert so yeah.
Ah gotcha. Ok, it would be.......both. ;D
I use both about the same. -
Hey, what can I say, I use all the tools on my Surge.
-
@HarleyXJGuy said:
Fan of the saw even though I use it not so much. But do you find yourself using the saw more then a good file? Not this guy.Saw - each of them alone not that often, but counted together (wood AND metal) i do.
File - one time, to test it when i bought the Surge.
A good file is often used by me - but they are full sized in my workbench, or the special type for my filing machine. ;)

-
I had to tickle a tiny bit off one corner of the saw too, so it locked easily when I moved it to the serrated blade slot. The small flat driver is modified too, to clear the lock pivot.
Not (yet) a Wave owner but I have a plan for a "Knifeless Wave". Couple of questions. Firstly taking account of length only could a 3D Phillips be made to fit in lieu of the bit holder?
Secondly the saw locking edge would have had the opposite bevel, presumably why it needed a bit of a grind. Once ground did it lock as securely as in the correct bay?
yes, the 3D Phillips from a Rebar/Blast/Fuse/Kick/etc. can be installed in place of the bit driver, but you'll need to either remove the blade safety lock pins or grind down the driver. take a look through the earlier pages of this thread and you'll see some examples. :D
-
@pingu said:
Secondly the saw locking edge would have had the opposite bevel, presumably why it needed a bit of a grind. Once ground did it lock as securely as in the correct bay?Yes. Well, if I'd not taken too much off it would have.
It only needed a very light touch - it may have been possible to bed it in without any grinding. -
@hiraethus said:
it may have been possible to bed it in without any grinding.Need I say it?
-
Have they stopped putting bromide in your tea or something?

-
@pingu said:
Secondly the saw locking edge would have had the opposite bevel, presumably why it needed a bit of a grind. Once ground did it lock as securely as in the correct bay?Looking again at the saw, there's a bit less than 1mm of play at the tip now, about the same as on the file (which hasn't been modified in any way). It still locks securely.
-
@hiraethus said:
Have they stopped putting bromide in your tea or something?
LOL! :D
-
Have they stopped putting bromide in your tea or something?

LOL! :D

-
Breazy and Hiraethus thanks.

If edgeing closer to knifeless Wavedom :ahhh is something to thank for. Seems extreme but I can't resist diamond coated files and I have something in mind for the small scissors and the bit holders.

-
Wanted to show off my SURGE ALX in progress:D. What ya think? Suggestions? Critiques? Questions? I'm gonna make a few long bits like the one pictured. I wanted to keep all the straight drivers on one side.
Does anyone have a charge alx serrated\gut hook blade they want to trade for parts I may have. I have a wave, fuse, blast, and of course the current serrated b.o blade on my surge (new model). Or ill be happy to pay as well. -
Thanks to JBW1, I was able to do this mod on my new style Surge.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login