Surge questions
-
Has super comfortable handles too.

-
Yeah all that is fine and dandy but are the scissors and comfortable handles worth the $100 it takes to buy a Surge? I don't think so.
Will I still buy one? You can bet your smurf I will.

Still looking for the best place to buy one though. Used is ok too since LM has that sweet warranty.
-
In answer to the original question, I'd say the "Multitools for Sale" or "Tools Needed" sections of the forum and have a look on EDC Source.
-
Yeah didn't think of EDC Source. Guess I always think of that place as Tims SAK store.
-
I have been wanting a new Surge myself. Sofar no luck with tools needed section here.
Seems that those whom have it, are not willing to depart theirs.
Ther is few good deals at Ebay, if you search a little... BO ones are not that much expencive than SS.
-
You can find them on Ebay and Amazon for around $80 to $100. As for being worth it. If you use your multipliers hard Lichbote, Joel, Zoid, myself and others, then yes. But if you just turning the rare screw, slicing an apple and cutting a stray thread, probably not the best tool to pack around. However, they are built like a M48 Patton, heavy, tough and can damn near tackle anything. There like a Wave but with armour plating and an awl.
-
The New Surge does have the Awl and Replaceable 154CM wire cutters.
The Surge is worth the lower end asking price IMO. I first got the Old Surge and was not surprised how quickly this tool booted my Wave off my belt for work.
When I got the NEW SURGE it immediately booted the old one out.
Matt's has a video that really got me excited for one -
Things I like about the surge I'm using
The outside opening scissors. So far my favorite tool on the surge. You will never realize how handy they are until you edc one.
Large outside opening blades. They have replaced the one hand folding knife always carried. Having both fully serrated and plan edge blades I feel I can cut whatever I need to with it.
The saw holder is nice. Having the right tool for the job makes things easier. I carry a few different saw blades to cut different things.
Complete tool setup in one tool. It has it all
Things I don't like.
I'd like a Phillips but I do use the bit driver with a extension often.
The clip doesn't fit.
The blade steel could be better on BOTH blades. There 420hc is ok but I'd prefer something better.
It's huge and heavy. It tool awhile to get used to and it still feels like a brick in my pocket .
I'm going to post this. IL add some more thought later.
stupid work

-
Oh man that video may be the straw and stuff. It is buffering now.
@JAfromMn said:
The saw holder is nice. Having the right tool for the job makes things easier. I carry a few different saw blades to cut different things.You can buy different blade for the holder somewhere?
I'd like a Phillips but I do use the bit driver with a extension often.
Yeah Rebar/ST300 for the win. If the ST300 had outside opening stuff it would be an impossible decision.
The clip doesn't fit.
**Pocket carry this beast?! Maybe in like a Carhart jacket but not your jeans right? **
The blade steel could be better on BOTH blades. There 420hc is ok but I'd prefer something better.
No S30V blade you can buy like the Wave huh? Maybe just build a mini surge like Kamp?
It's huge and heavy. It tool awhile to get used to and it still feels like a brick in my pocket .
Pfft I got that problem already!

-
I believe Matt is a member here. If I am recalling correctly he lost his Surge then got a call and some one found it where he was working last.
Anyway, you can buy the saw blades anywhere the sell T shank blades.
I turn a fair amount of all types of screws and the LM bits haven't failed me yet.
I carry mine in a sheath and while the pocket clip "works" on the Surge its just to big to me to pocket carry.
I know many here are more knowledgeable than me on blade steels but the steel for most applications is fine. I cut anything from rubber to plastic and have found the blade to be more than adequate. I also routinely ( weekly ) use ceramic rods to touch it up as I do will all my blades.

-
Blade exchanger is a great idea.
Carrying all them blades in your front pocket not so much. How do you carry them around?
-
I carry some in the provided plastic sheath and the others ride in the nylon sheath the tool came with.
The blade exchanger puts this tool over the top especially when adding the LM bits to this tool. If you saw anything from wood to metal then this is the way to go.
-
The plastic sheath the extra blade came in holds a few of the thinner saw blades ok. Kam made a duct tape sheath iirc and posted a how to somewhere.

-
Mini-Surge wins! :D
I EDC a Surge set in my laptop case.
-
Yea, Surge is the tool I reach for if it is around.
It is a "Tool box", no kidding.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

