The Commander (LM Super Charge Mod)
-
Thread Necro!
Metro, any Chance i can talk you out of a set of those grip add ons? I don´t mind some fabricating work to make them fit. Maybe i could talk you into cutting the tip of yet another Leatherman plier head, too?!
-
Thanks for following up, but i think my wishes have been fulfilled (just waiting for teh postman and contemplating if i should have a go at 3D printing or try to make those parts from Aluminium myself)
-
@lowtech said:
Thanks for following up, but i think my wishes have been fulfilled (just waiting for teh postman and contemplating if i should have a go at 3D printing or try to make those parts from Aluminium myself)my aluminum ones were fun and they worked great. The hardest part is attaching them. If I was more brave, I would go with JB Weld or something simliar.
-
Thinking about this and I wonder if you drilled a 2.5 mm hole in both and use a old Alox pin if you could peen the other side?
-
SOO jealous! I love my surge, and I cannot wait for the new surge in a few months, but this is a super cool mod! I do not love the Surge because it is heavy duty, I love it because it has everything I want, and a REPLACEABLE saw and file is on top of the list. I do not have to worry about ruining them, I can just buy more! :ahhh
Great work, with I had the tools, and the knowledge (and money) to do stuff like this
-
@tattoosteve99 said:
Thinking about this and I wonder if you drilled a 2.5 mm hole in both and use a old Alox pin if you could peen the other side?There is too much going on underneath that area. The split knife pins, the rivet for the tool lock back spring. Adhesive is the way to go here.
-
And there was me thinking the other day about a smaller surge and bame eric scores again
great work mate 
-
best mod i've ever seen. i really like the handle part that you put there with the toothpick and the tweezers, i think you could add a another piece like that on the pocket clip, make it a little bit bigger and you could add a SA pen.

-
Well done sir!

I could go for one of them, 'cept keeping the can opener. Though a push opener would be preferred, though not seen anything past a Vic knife that has that.
-
@Metropolicity said:
Wanted to waste some time in the shop late on a Friday night.Chucked up some 6061 and milled out some grips. The jimping isn't as nice, I only have 7/32 ball mills at the moment.
Here is fresh off the mill, test fitting.



After a 100 grit sand paper.


....and after a 400 grit wet sand, installed with doubled sided tape.



I used the blade profiles as a template. So the grips aren't protruding past them, and follow the curve.


The extra filler of the grips makes for a nice meaty grasp when using the drivers. It also solved the problem I was having with the blade exchanger digging into my hand.

Great Mod

-
Nice necro Obi

-
@sLaughterMed said:
Nice necro Obi
:ahhh :ahhh :ahhh :ahhh
-
@Metropolicity said:
I took this one out of enki_ck's book:VIC SCISSORS!
Easiest scissor mod, no need to pin anything, just simply needed to bore out the pivot hole from 3mm to 7/32. Again, carbide bits made this easy. Since I already pushed in the liner lock so it wouldn't push up against the scissors, this was a simple drop in.
Seriously....no mods whatsoever.

The Vic's scissors are going to leave plenty of room for the ferro rod, whenever they get here..


They are a pleasure to use like all Vic scisssors, not as cool or as crisp as the Gerber ones but these are much more accessible and cheaper. A simple, even used SAK can be used to harvest a pair.


Im quoting way back here.
What size scissors (or what model sak) did those come out of?
And they are NOT locking correct?
-
I took this one out of enki_ck's book:
VIC SCISSORS!
Easiest scissor mod, no need to pin anything, just simply needed to bore out the pivot hole from 3mm to 7/32. Again, carbide bits made this easy. Since I already pushed in the liner lock so it wouldn't push up against the scissors, this was a simple drop in.
Seriously....no mods whatsoever.

The Vic's scissors are going to leave plenty of room for the ferro rod, whenever they get here..


They are a pleasure to use like all Vic scisssors, not as cool or as crisp as the Gerber ones but these are much more accessible and cheaper. A simple, even used SAK can be used to harvest a pair.


Im quoting way back here.
What size scissors (or what model sak) did those come out of?
And they are NOT locking correct?
I believe they are standard 91mm scissors and yes not locking because the liner lock has been pushed in.
-
I took this one out of enki_ck's book:
VIC SCISSORS!
Easiest scissor mod, no need to pin anything, just simply needed to bore out the pivot hole from 3mm to 7/32. Again, carbide bits made this easy. Since I already pushed in the liner lock so it wouldn't push up against the scissors, this was a simple drop in.
Seriously....no mods whatsoever.

The Vic's scissors are going to leave plenty of room for the ferro rod, whenever they get here..


They are a pleasure to use like all Vic scisssors, not as cool or as crisp as the Gerber ones but these are much more accessible and cheaper. A simple, even used SAK can be used to harvest a pair.


Im quoting way back here.
What size scissors (or what model sak) did those come out of?
And they are NOT locking correct?
I believe they are standard 91mm scissors and yes not locking because the liner lock has been pushed in.
Yeah been searching and searching for awhile, trying to find a cheap one on ebay for now
-
@Metropolicity said:
Tweezers and Toothpick/Knife gripsAfter failing twice at manually milling this piece from a couple of small scraps of titanium, I gave in a went digital. I've toyed with adding a plate on the sides for extra grip. I had a mildly successful attempt when I made my own "Flair", AKA The Panache. A brass plate was added, jimping was hand filed...this will be so nice.




What you are looking at are two plates that will be epoxied on the flat surfaces on the Commander, what you don't know is that they are getting printed in alumide and black plastic (for now at least) from Shapeways.

These plates serve a much more Swiss purpose than just aesthetics. Not only are they grips and jimping for the use of the outside tools, the two hollow cavities will be hold a set of Vic Classic Tweezers and Toothpick!

Here's a visual reference of how the T&T will sit.

The hole and gap in the bottom will accomodate the rivet on the side of the Commander, this also serves as a pressure point to hold the tweezer and toothpick. Here's a really bad rendering...the T&T will pull towards the knife pivots.

I ordered a set of black plastic and a set of alumide...over all $20 and should be here by the new year. Once I know they fit, I'll order the polished stainless. I'll need to some hand finishing, I didn't want to fire up SolidWorks...most because this is an extruded shape, but I also didn't want to get into 3D modelling hell.
Metro, I know this is an OLD thread, but Did these ever make it to Shapeways?
-
Metro, PM sent. [emoji1]
-
Hi Eric!
Sorry that I return this thread on the beginning (in some way), as beginner I need to clarify can I just swap pliers between xTi and Rebar without any additional modification to the pliers or the Charge body?
Thanks!
-
You can do a direct swap, but the pliers won't fully close unless you remove part of the scissor thumb plate or grind a bit of the plier head by about 2mm.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login