The Commander (LM Super Charge Mod)
-
And there was me thinking the other day about a smaller surge and bame eric scores again
great work mate 
-
best mod i've ever seen. i really like the handle part that you put there with the toothpick and the tweezers, i think you could add a another piece like that on the pocket clip, make it a little bit bigger and you could add a SA pen.

-
Well done sir!

I could go for one of them, 'cept keeping the can opener. Though a push opener would be preferred, though not seen anything past a Vic knife that has that.
-
@Metropolicity said:
Wanted to waste some time in the shop late on a Friday night.Chucked up some 6061 and milled out some grips. The jimping isn't as nice, I only have 7/32 ball mills at the moment.
Here is fresh off the mill, test fitting.



After a 100 grit sand paper.


....and after a 400 grit wet sand, installed with doubled sided tape.



I used the blade profiles as a template. So the grips aren't protruding past them, and follow the curve.


The extra filler of the grips makes for a nice meaty grasp when using the drivers. It also solved the problem I was having with the blade exchanger digging into my hand.

Great Mod

-
Nice necro Obi

-
@sLaughterMed said:
Nice necro Obi
:ahhh :ahhh :ahhh :ahhh
-
@Metropolicity said:
I took this one out of enki_ck's book:VIC SCISSORS!
Easiest scissor mod, no need to pin anything, just simply needed to bore out the pivot hole from 3mm to 7/32. Again, carbide bits made this easy. Since I already pushed in the liner lock so it wouldn't push up against the scissors, this was a simple drop in.
Seriously....no mods whatsoever.

The Vic's scissors are going to leave plenty of room for the ferro rod, whenever they get here..


They are a pleasure to use like all Vic scisssors, not as cool or as crisp as the Gerber ones but these are much more accessible and cheaper. A simple, even used SAK can be used to harvest a pair.


Im quoting way back here.
What size scissors (or what model sak) did those come out of?
And they are NOT locking correct?
-
I took this one out of enki_ck's book:
VIC SCISSORS!
Easiest scissor mod, no need to pin anything, just simply needed to bore out the pivot hole from 3mm to 7/32. Again, carbide bits made this easy. Since I already pushed in the liner lock so it wouldn't push up against the scissors, this was a simple drop in.
Seriously....no mods whatsoever.

The Vic's scissors are going to leave plenty of room for the ferro rod, whenever they get here..


They are a pleasure to use like all Vic scisssors, not as cool or as crisp as the Gerber ones but these are much more accessible and cheaper. A simple, even used SAK can be used to harvest a pair.


Im quoting way back here.
What size scissors (or what model sak) did those come out of?
And they are NOT locking correct?
I believe they are standard 91mm scissors and yes not locking because the liner lock has been pushed in.
-
I took this one out of enki_ck's book:
VIC SCISSORS!
Easiest scissor mod, no need to pin anything, just simply needed to bore out the pivot hole from 3mm to 7/32. Again, carbide bits made this easy. Since I already pushed in the liner lock so it wouldn't push up against the scissors, this was a simple drop in.
Seriously....no mods whatsoever.

The Vic's scissors are going to leave plenty of room for the ferro rod, whenever they get here..


They are a pleasure to use like all Vic scisssors, not as cool or as crisp as the Gerber ones but these are much more accessible and cheaper. A simple, even used SAK can be used to harvest a pair.


Im quoting way back here.
What size scissors (or what model sak) did those come out of?
And they are NOT locking correct?
I believe they are standard 91mm scissors and yes not locking because the liner lock has been pushed in.
Yeah been searching and searching for awhile, trying to find a cheap one on ebay for now
-
@Metropolicity said:
Tweezers and Toothpick/Knife gripsAfter failing twice at manually milling this piece from a couple of small scraps of titanium, I gave in a went digital. I've toyed with adding a plate on the sides for extra grip. I had a mildly successful attempt when I made my own "Flair", AKA The Panache. A brass plate was added, jimping was hand filed...this will be so nice.




What you are looking at are two plates that will be epoxied on the flat surfaces on the Commander, what you don't know is that they are getting printed in alumide and black plastic (for now at least) from Shapeways.

These plates serve a much more Swiss purpose than just aesthetics. Not only are they grips and jimping for the use of the outside tools, the two hollow cavities will be hold a set of Vic Classic Tweezers and Toothpick!

Here's a visual reference of how the T&T will sit.

The hole and gap in the bottom will accomodate the rivet on the side of the Commander, this also serves as a pressure point to hold the tweezer and toothpick. Here's a really bad rendering...the T&T will pull towards the knife pivots.

I ordered a set of black plastic and a set of alumide...over all $20 and should be here by the new year. Once I know they fit, I'll order the polished stainless. I'll need to some hand finishing, I didn't want to fire up SolidWorks...most because this is an extruded shape, but I also didn't want to get into 3D modelling hell.
Metro, I know this is an OLD thread, but Did these ever make it to Shapeways?
-
Metro, PM sent. [emoji1]
-
Hi Eric!
Sorry that I return this thread on the beginning (in some way), as beginner I need to clarify can I just swap pliers between xTi and Rebar without any additional modification to the pliers or the Charge body?
Thanks!
-
You can do a direct swap, but the pliers won't fully close unless you remove part of the scissor thumb plate or grind a bit of the plier head by about 2mm.
-
XTi doesn't have scissors. Plier head from a Rebar is drop in.
-
@vadsoom said:
You can do a direct swap, but the pliers won't fully close unless you remove part of the scissor thumb plate or grind a bit of the plier head by about 2mm.@Toolslinger said:
XTi doesn't have scissors. Plier head from a Rebar is drop in.Guys thanks for the answers. My concern was about the locks of the knifes, the saw & the file when the pliers are in opened position. Look like it would be my first LM modification.
-
You can do a direct swap, but the pliers won't fully close unless you remove part of the scissor thumb plate or grind a bit of the plier head by about 2mm.
@Toolslinger said:
XTi doesn't have scissors. Plier head from a Rebar is drop in.Guys thanks for the answers. My concern was about the locks of the knifes, the saw & the file when the pliers are in opened position. Look like it would be my first LM modification.
Won't be a problem on the XTi. The Rebar pliers seat properly and allow the blade locks to function normally.
-
You can do a direct swap, but the pliers won't fully close unless you remove part of the scissor thumb plate or grind a bit of the plier head by about 2mm.
@Toolslinger said:
XTi doesn't have scissors. Plier head from a Rebar is drop in.Guys thanks for the answers. My concern was about the locks of the knifes, the saw & the file when the pliers are in opened position. Look like it would be my first LM modification.
Won't be a problem on the XTi. The Rebar pliers seat properly and allow the blade locks to function normally.
Thanks Toolslinger, that's the answer I was looking for.
-
Could we potentially get a link to some pictures? the original are long since gone
-
is there somewhere I can get your grip attachments you had on the commander and the wave? I am looking into ways to store extra tools like tweezers on the wave, and I do not want to use the keyring slot, I am also trying to figure out how to carry a second bit on it without a sheath
-
@NicknameNMS said:
is there somewhere I can get your grip attachments you had on the commander and the wave? I am looking into ways to store extra tools like tweezers on the wave, and I do not want to use the keyring slot, I am also trying to figure out how to carry a second bit on it without a sheathThis may help. This is metros stuff
Shapeways & Thangs Marketplace for 3D Creators - Shapeways Blog
Discover the Thangs Marketplace powered by Shapeways — a new 3D printing platform where creators can sell, print, and share designs.
(www.shapeways.com)
Also go to https://skinthsolutions.com/ as this is his site. Shoot him a message. He’s usually quick to respond. Hope that helps some.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login