Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Replace worn out hook and loop with snaps

Scheduled Pinned Locked Moved Sheaths, Bags, Packs and Carry Methods
5 Posts 1 Posters 3.3k Views
  1. Home
  2. Non Tool Forum
  3. Sheaths, Bags, Packs and Carry Methods
  4. Replace worn out hook and loop with snaps
Replace worn out hook and loop with snaps
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • parnass Offline
    parnass
    Posts: 1,653
    parnass Offline
    parnass
    wrote on last edited by
    Quote Reply

      I am not a fan of noisy, lint attracting hook and loop ("Velcro") fasteners used in holsters. So when the hook and loop wears out, I drill holes through the nylon fabric and install metal snaps.

      Too, I use a black felt tip marker to subdue the brand labels or remove the labels completely, as done with the Nite-Ize Mini-Pock-Its shown below.

      Merit Badges
      Flashlight OCD Squad BO Tools Level 2
      1 Reply Last reply
      • Spoonrobot Offline
        Spoonrobot
        Posts: 1,894
        Spoonrobot Offline
        Spoonrobot
        wrote on last edited by
        #1 Quote Reply

          So, what's all involved in adding snaps?

          I've seen the kits they sell at hobby shops but haven't ventured to try one yet.

          1 Reply Last reply
          • parnass Offline
            parnass
            Posts: 1,653
            parnass Offline
            parnass
            wrote on last edited by
            #2 Quote Reply

              A basic overview of snaps appears here.

              There are two basic types of snaps: post style and prong style. The best type for use on nylon holsters is the post type which requires making a single hole in the holster cover and another mating hole in the holster body.

              Each snap is composed of 4 pieces (see attached photo):

              • cap

              • stud

              • socket

              • eyelet

              There are a few ways to make the holes in your nylon holster to accommodate the snap post. I used an electric drill, but you might melt a hole with a heated awl or nail instead. Be sure the hole isn't larger than the snap's post diameter or else the snap will fit too loosely.

              I placed a small block of wood inside the holster before drilling to avoid drilling through the entire holster and out the back. :D

              Some inexpensive snap assortment kits come with a pin punch-type installation tool which you hit with a hammer. I found that difficult to use and easy to smash your fingers. Instead, I use a pliers style tool similar to this Dritz® Mighty Snap-A-Plier For Heavy Duty Snaps:

              http://www.joann.com/joann/catalog/productdetail.jsp?CATID=cat2851&PRODID=prd34657

              I have 2 sizes of snap, each with different length posts. If the nylon material is too thick, the shorter post snaps won't reach through. If you have snaps with a post which is too long, you can either shorten the post using a Dremel tool and cutoff wheel, or just install a washer as a shim. The latter workaround is easier, though using a shim washer can cause the snap to protrude a little further from the material.

              Suggest you practice first on a scrap piece of nylon or leather.

              snap-pieces.jpg

              Merit Badges
              Flashlight OCD Squad BO Tools Level 2
              1 Reply Last reply
              • Spoonrobot Offline
                Spoonrobot
                Posts: 1,894
                Spoonrobot Offline
                Spoonrobot
                wrote on last edited by
                #3 Quote Reply

                  Hey, thanks. Converting over my remaining Velcro sheaths should make a good afternoon project.

                  1 Reply Last reply
                  • jzmtl Offline
                    jzmtl
                    Posts: 8,551
                    jzmtl Offline
                    jzmtl
                    wrote on last edited by
                    #4 Quote Reply

                      I always use a hot nail, no fray this way.

                      1 Reply Last reply

                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                      With your input, this post could be even better 💗

                      Register Login

                      1. Home
                      2. Non Tool Forum
                      3. Sheaths, Bags, Packs and Carry Methods
                      4. Replace worn out hook and loop with snaps
                      Reply
                      • Reply as topic
                      Log in to reply
                      COMMUNITY LINKS
                      EDC-TV SAKWiki GearFeed SAKSelector
                      Operational Funds

                      Help us keep the Unworkable working!

                      Make A Donation
                      November Goal: $300.00
                      Due Date: Nov 30
                      Total Receipts: $0.00
                      Below Goal: $300.00
                      0% funded
                      • Login

                      • Don't have an account? Register

                      • Login or register to search.
                      • First post
                        Last post
                      0