New guy with a bit extender problem/question...
-
Greetings,
So I've bought myself a surge and like the thing enough so that I also bought the bit set and a bit extender.
I inserted one of the bits into the extender and couldn't get the thing out without clamping the bit in a vice and using a large flat head screwdriver to lever the extender up off the bit.
Looking inside the extender with a loupe, I notice that the metal ring that is clearly supposed to retain the bit is doubled up for at least two of the flats instead of either just meeting at the ends or even perhaps having a little gap.
The Vendor double processed my order so I actually have another bit extender here that came from another shipping point and it shows the same type of retention ring overlap.
is it just my luck or do the bits sometimes get stuck and need a good deal of force to get them out. Were I out on the road some where and not have access to a vise I can't see how I'd have gotten the bit out.
Other than this one little wrinkle and a few sharp edges (that I've already taken it's own file to) I'm happy with it.
-
I just got one of these and I always have to use the pliers to remove the bit from the extender. They are very tight in there, but better than loose I suppose. I already used mine a couple times since I got it this week.
-
@Marlinaholic said:
I always have to use the pliers to remove the bit from the extender.@tg579 said:
Greetings,
couldn't get the thing out without clamping the bit in a vice
Were I out on the road some where and not have access to a vise I can't see how I'd have gotten the bit out.One more reason to carry several pliers multi-tools!


-
They were so tight in there that I couldn't pull them out using the pliers or even a real set.
My short term solution has been to take a sharpie and mark the barrel of the extender outside the flats where the doubled up retention ring is. I found that if I make sure I put the bit in so it's not locking on that spot, that I can get them out without to much of a fight.
Now after playing with it some more, the only thing that's un-sat is the scissors. Seams the liner lock is not engaging enough to let you actually use the scissors against the spring without them popping out of lock.
No big deal though... I'd almost never need scissors. I'm looking for another surge on ebay that's cheap/broken or what ever so that I can find another of the file/saw holders to replace the scissors with.
TG
-
For future archive readers.....
It turns out that in at least one of the extenders, the retention ring is actually free to rotate within it's groove. Thus my measure of marking the outside of the extender and making sure I index the bit to not hit the doubled section is for naught.
Knowing this, I'll just have to make sure I look inside it before putting a bit it.... gonna be a pain if it's o'dark thirty and I can't for whatever reason get to or use my flashlight.
-
This sounds like a warranty issue. You could email LM.
-
I wondered about that... See I've got a BMW motorcycle and "They all do that" is a normal reply to odd things that they do.
The fact that I have two bit extenders from totally seprate warehouses that exhibit the same thing makes me think that is just how they are.
I figured that if anyone had them that looked different, they'd chime in by now.
I'm still liking this thing very much. Made myself a chisel today based on a post here that shows how to make one from a spade bit.
Gotta love tinkering in the garage.
-
Just got the extender in the post this morning, bit got stuck immediately and couldnt remove it even with wiggling and pliers. managed to get it out by holding the bit in vice and pulling on the extender itself with some swearing and wobbling. Put a little grease in there and tried again but didnt help secnd time was just as bad.
The ring in mine spun freely (uk stock) so my thought was to stretch the spring to push itself hard against the outer in the hope it would then have less grab on the bits. After 30min trying different approaches and the spring in and out a few times but with no real benefit.
Ive now removed the ring/spring entirely and dropped a 2mm x 6mm N52 magnet in the bottom which seem perfectly adequate for holding even the smallest LM flat bit and actually brilliant better for standard bits as they now sit higher. I was going to glue it in but so far its stayed in place just by a little friction against the sides and the magnetism.
Obviously this ring idea is a bit smurf ??? anyway apart from feeling like a mug paying £25 / $30 it looks and works great now, cant help feeling id have been better off just filing down a standard extension for 1/4 of the price and probably the same amount of time i spent messing about with the official one!!

-
That’s not good at all.

-
Thats weird problem, i dont have any problems with my extender, i can move bits easily from extender and put them there.
Only Tools Matters
-
Thats a bummer :(. You can always mod your own bit extender
. Just use a bit to determine how much material you want off a random extender you might have or one you can get reasonably cheap. Grind away needed material and fit into bit holder. I've made a few and they work great. Add magnet if needed or mod one that already has magnet
. -
Mine is also new, but works smoothly
I took a look into the holder, and the ring does have roughly 4mm of overlap, I can barely feel the bits lock in, and they release smoothly -
Great thread necro though.

-
We don't mind necro threads here on MTo ;)
-
I've had the exact same problem on the first extender I've bought some years ago for my Wave.
I took the ring out, cut off the overlap part and put it back. No problems since
-
Bought mine the other day. As soon as I put it in it got stuck immediately. Found this forum and saw that everyone else has had the same exact issue.
After reading through and hearing how much people were struggling to pry it out. Now this of course will only work if you have a brazing torch. Took my torch heated up the end till it was bright red and was able to remove it easily. Pretty insane that this is what Hass to be done to do it without any swearing or too much headache but going to remove the ring that binds the bit inside and put a magnet in the bottom which one of the other uses recommended. -
Welcome to
tgasbarro
Hope that the fix works out for you 
-
BOTH of the two extenders I have had lock in bits..ESPECIALLY normal hex bits. I may just add a magnet like others have done..
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


