PST cleaning help
-
First a story. My grandfather died 7 years ago and only now have we finished going through the last of his stuff. Anyway, we found a Leatherman PST in a box of his duty gear (he was a career police officer). We couldn't find the original leather pouch for it. The tool itself is in fairly good condition except for the tools in the handles. The tools are either quite rusted around the pivot or gummed up by something. Other than 7 years of dust and slightly twisted pliers, its ok. What are your suggestions for getting the rust/grime out of the pivots? I want to get it cleaned up and usable but I don't want to damage the tool. It has those **** tamper-proof fasteners... Also, what kind of oil would you recommend? Thanks in advance!
-
First thing I'd do is soak it in WD40 for a good while, then try and get it apart and use very fine wire wool to try and the rust off.
-
What would I use to take the bolts off with? I took a LM Kick apart with a two vise-grips, but it really mangled the bolts.
-
I had a gummed up one as well. The tools were nearly frozen. As a member here suggested I soaked it in WD-40 for a day. It worked great. If that doesn't work, run it through the dishwaher and oil afterwards. Congrats on the tool.
-
@darth_guy101 said:
What would I use to take the bolts off with? I took a LM Kick apart with a two vise-grips, but it really mangled the bolts.Maybe I should say I tried to take a LM Kick apart... I still haven't gotten it yet... >:(

-
There's no need to take it apart. You can get it very clean without doing so.
Good luck :) -
I've gone through the same thing before with a gunked up MT.
What I did.....
-
I submerged it overnight in Break-Free CLP (soak it in CLP and begin opening and closing all blades, also open and close pliers to make sure the oil has penetrated properly... then let it sit overnight)
-
Clean the oil off by wiping with rag/paper towel etc.
-
Hold the tool under hot running water to rinse hard to reach spaces (you're trying to remove as much oil as possible)
-
fill a cooking pot or pan with enough water to submerge the tool
-
boil the water on the stove with the tool in it (it won't hurt the tool.... just bring the water to a boil and allow it to boil for at least a minute... this will loosen all gunk for sure)
-
remove tool carefully and dry it off (have another set of pliers on standby to help you remove the gunked one from the boiling water.... be sure to let the tool cool down a little before you handle it... shouldn't take more than 60 secs)
-
apply a little Break-Free CLP to all pivoting areas and you're ready to go ;)
The tool should be function as if it were brand new!
I did this procedure with one of my Wave's... it worked great
-
-
Keep in mind that all Leatherman Tools have thread locker to keep them from falling apart. There are a couple of ways to get your tool taken apart.
First the pocket clip for the Kick has the correct spline on the clip to loosen the screws. But there is a piece folded down on the clip to prevent it from rotating when you have it on the Kick, so cut it off with a Dremel cut-off wheel. So get a couple of pocket clips for the Kick.
If you hold a PST with the plier head down in your left hand and the tools on the right side of the tool the "screw" side of the PST will be facing you. There is a screw and a nut involved, the tools pivot on the nut side of the tool. The key is to loosen the screw and leave the nut side of the pivot in the tool. Sometimes I just try to rotate the pivot (nut side) to try to loosen up the tool. A little heat really helps to loosen up the thread locker but of course then you need to use gloves so you don't burn yourself. Just a second or two from a candle, jet type butane lighter or a blow dryer if you heat it a little longer. Be sure you only remove the screw side and then you can usually use a small tool to push the nut out and still keep the tools in order. Be careful to note the location of any thin washers in the tool stacks and the order and location (Which handle) where they were located. Pictures and notes really help, I know because I did not do either! I think every PST has at least 1 washer on either side of the file.
My instructions do you no good if you have a riveted PST, but at least it has more value than just the sentimental value.
I like to soak a tool in a jar with some penetrating oil before I take it apart for a week or so then put it back in a jar for another week when in pieces. If your wife has a ultrasonic jewelry cleaner they work really nicely....but don't get caught using it for your tools! Just clean up the tool as well as possible and use a little dishwashing liquid as the cleaner in the ultrasonic cleaner. Be sure to run it several times to get it (both the tool and ultrasonic) clean. I like to soak the clean parts in another jar with clean penetrating oil before I put it back together.
To put it back together I like to stack the tools and washers and try to slide them into the handle and put something like a pick or small pick through from the screw side and use the nut to push the pick back out while I use the pick to line everything up. Good light and patience will prevail....eventually.
When I have the tool re-assembled I just play with it over a couple of days to try to determine if everything is ok and how tight I want the pivots. When I am ready I remove the pivot screw and put loctite (thread locker) on the screw and tighten it to the predetermined torque. If I get it too tight or loose I just heat the screw a little and tighten or loosen the screw a little. The thread locker can be reheated and will lock the threads again.
Where do you live? Since the tool has sentimental value I might be able to give you a hand.
Let us know how it goes for you and give a shout if you need help.
Bruce
-
Bruce that was a very clear and detailed set of instructions

-
Thanks Dunc,
I just hope it makes sense before you have actually done the deed. I hope to take pictures the next time I take one apart. I did buy a 4 piece hook and pick set that helps with the work.
Bruce
-
I just finished getting it cleaned up. All it really needed was an overnight WD-40 bath, some hot water rinsing and a wipe down. I put a little 3-in-1 oil after I dried it (in my toaster oven :D) wiped of the excess and it works great! I'm still playing with it to get the oil around in all the joints and I even gave the file a thin coat too. I think I'll carry it for a few days just to say I did. Thanks for all the help!
-
Is there any way that I can tell when it was made? I've looked for a date-stamp type thing but I can't seem to find one. Where might I need to look? ???
-
If it has one, it will be in the handles under the tools. Mine is a 1098 and the code is very faint but there. If it doesn't have one it's probably a pre- 1993? tool.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login