Electrical Help
-
Additional to pm's ...
Have a look at this and tell me what will actually fit (size wise) ...
http://www.gnbsystems.com/12_volt_multipurpose.php -
Imagine water as electricity. Voltage is like a small hole in water line. Now that same size hole is in a dam and it has more amps (push) behind it. Same size hole just different force. That's the way it was explained to me and it helped.
-
Voltage is like pressure.
Amperage is like flow.
Wattage = voltage x amperage.Grant, I think that you should get your Jeep the highest output alternator you can afford to fit. Then upgrade all the wiring from the alternator to the batteries. Add a deep cycle battery (I prefer Optima yellow top's because they last a very long time) and a battery isolator - this connects between the alternator and the batteries positive terminals and allows you to keep from draining both batteries while charging both of them from the alternator. Then you'd have to move all the expected loads (stereo, power outlets, etc) to the second battery. It sounds more complicated than it actually is. :)
Now, just to be a realist, didn't you recently mention having rust issues with the frame on your Jeep? If this is correct, throw some ice cubes into your boxers and carefully reconsider any further investments into your Jeep. Still want to spend money on it? Get more ice. Repeat as required until you change your mind. This will hurt much less than spending every last penny on your beloved vehicle only to loose it to the cancer that rust is. Believe me, I know...
Dave
Sent from my iPad2
-
With all respect I would disagree completely, too big an alternater could adversely affect the batteries. A cranking battery will accept charge at a different rate to a deep cycle battery (cranking tend to be more forgiving), and if you try to "force feed" them you'll just hurt them.
As for the isolator I would recommend a split charge relay, as there's no worries then about forgetting to turn it on when charging and off to avoid transfer to the cranking battery. A bigger alternator would just mean that heavier cables, connections, fusing and relays are required ... as well as the battery issues.
There's just no benefit in simply going for the biggest possible IMHO.
-
@50ft-trad said:
With all respect I would disagree completely, too big an alternater could adversely affect the batteries. A cranking battery will accept charge at a different rate to a deep cycle battery (cranking tend to be more forgiving), and if you try to "force feed" them you'll just hurt them.As for the isolator I would recommend a split charge relay, as there's no worries then about forgetting to turn it on when charging and off to avoid transfer to the cranking battery. A bigger alternator would just mean that heavier cables, connections, fusing and relays are required ... as well as the battery issues.
**
There's just no benefit in simply going for the biggest possible IMHO.**Agree with this.
Of course, if the rusting problem is bad, maybe going whole hog on this and getting a DC Welder set up for the Jeep is a good option!

Talk about EDC!
-
Another option would be 2 alternators. One for the jeep and the other for the extra battery. More work though as you have to wire it in and add brackets and belt. But just a thought.
-
Dave, you have a very good point about the rust, and I agree with you to an extent. However, a new vehicle just isn't in the budget right now. Maybe a year or so down the road, but not right now. Ideally I would like to drive this Jeep every day for the rest of my life, and I do form an unnatural bond with things even though I know it's just a piece of machinery.
Besides, I'd rather put $1000 into this one and keep it a couple more years than to have to put down several thousand now and get into a $400 payment each month for a new one.
Def
Sent from my MB860 using Tapatalk 2
-
Just to give a bit of an update- I have ordered a 117 amp OEM replacement alternator for my Jeep. I'm not sure if it has an 81 or 117, but the 81 was standard and the 117 was optional on it, so I'm taking the bigger one. I'll let you know if it catches fire...
Def
-
Good luck mate. Give me a shout if you need anything

-
I'm sure I will- but the price was right ($150) for the OEM 117 amp alternator versus the Mean Green ($400) one that produced up to 220 amps. OEM means no screwing around installing it and no issues with the existing cables too, which is also a huge benefit.
And, as if that wasn't enough, I can pick up the OEM one a few blocks from my house tomorrow morning rather than ordering the Mean Green version from the US and waiting for it. And I need my Jeep back on the road. I hate taking the VW to work as it will get the crap kicked out of it.
Def
-
Well, if a standard is 81A and you've gone for 117A - you've got an extra 36A to play with over and above what the Jeep needs. If you're sticking to phone charging, stereo and computer use, and not running winches or other heavy duty ancilleries, you'll still be fine adding in a leisure (deep cycle) battery

-
I'd like to add a winch sometime, but my understanding with that is that you only use the winch with the motor running, which I would have anyway without the warning.
Def
Sent from my MB860 using Tapatalk 2
-
Well, the new alternator is in and happy, but it looks like I need a new starter too. If this keeps up I'll have a whole new truck soon!
Def
Sent from my MB860 using Tapatalk 2
-
As long as you always park on a hill you won't need that new starter ;D
Sent from my Galaxy Nexus using Tapatalk 2
-
Yes, although sadly I didn't park on a hill this time, I parked in the yard.

Ah well, I think I'll leave the starter for the mechanic next week rather than do it myself since he'll have it on the hoist for the welding anyway. So much for trying to get ahead!
Def
-
Bah, push start it, that's like a free gym membership. :D
The starter is literally a two bolt job, very easy to access and you can probably change it under 10 minutes.
-
Really? My Haynes manual says I may have to remove my exhaust or other parts to get at it.
Def
Sent from my MB860 using Tapatalk 2
-
Hmm, anything I've ever changed a starter on has always had enough clearance that nothing else had to be removed, but I've never looked at a TJ before to see how tight things are.
Ha, my old Bronco II I had to push start where ever I went. Use to get some funny looks when I would start pushing it than jump in and pop the clutch ;D
Sent from my Galaxy Nexus using Tapatalk 2
-
What? Remove exhaust? I took mine off to resolder wire between solenoid and motor and it was as simple as unplug and unscrew.
Did I ever send you the Chrysler factory service manual? Way better than Haynes. If not PM me your email and I'll send the PDF.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
