Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Broken Wave?

Scheduled Pinned Locked Moved Leatherman Tools
22 Posts 1 Posters 3.2k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Broken Wave?
Broken Wave?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • scorpion008 Offline
    scorpion008
    Posts: 139
    scorpion008 Offline
    scorpion008
    wrote on last edited by scorpion008
    Quote Reply

      Is this pivot not up to standard or is this normal play? I was trying to cut a bullet casing which is quite thin and it refused to cut. It got stuck pretty good though ever time. Also, when I close up my Wave it clicks at the last few mm because of a tiny burr in the wirecutters. That was caused by a screw about 2 mm diameter. Also, the wirecutters don't cut paper or any kind of stranded wire. Do I need a Rebar head for actual wirecutting?

      rsz_dsc00002.jpg

      1 Reply Last reply
      • bmot Offline
        bmot
        Posts: 4,468
        bmot Offline
        bmot
        wrote on last edited by
        #1 Quote Reply

          Mine doesn't have any play in the pliers pivot... Don't think that'd be normal...

          1 Reply Last reply
          • Farmman Offline
            Farmman
            Posts: 911
            Farmman Offline
            Farmman
            wrote on last edited by
            #2 Quote Reply

              No that is not normal. Is it a new tool or has it had some stick?

              1 Reply Last reply
              • Romanoat Offline
                Romanoat
                Posts: 333
                Romanoat Offline
                Romanoat
                wrote on last edited by
                #3 Quote Reply

                  Mine isn't like that at all. Definitely not right...

                  1 Reply Last reply
                  • dks Offline
                    dks
                    Posts: 21,823
                    dks Offline
                    dks
                    wrote on last edited by
                    #4 Quote Reply

                      Definitely damaged!

                      If it is new take it back to the dealer/seller.

                      I do not think it can be fixed easily at home.

                      1 Reply Last reply
                      • scorpion008 Offline
                        scorpion008
                        Posts: 139
                        scorpion008 Offline
                        scorpion008
                        wrote on last edited by
                        #5 Quote Reply

                          More info up. I was cutting something in the pic, so I wasn't holding them apart, that is too difficult. Got the Wave for Christmas, so it is new.

                          1 Reply Last reply
                          • dks Offline
                            dks
                            Posts: 21,823
                            dks Offline
                            dks
                            wrote on last edited by
                            #6 Quote Reply

                              In reply to your edited post, the wave can cut wire too, though all tools have their limits.

                              Maybe the wire was just too hard or possibly too thick

                              1 Reply Last reply
                              • scorpion008 Offline
                                scorpion008
                                Posts: 139
                                scorpion008 Offline
                                scorpion008
                                wrote on last edited by scorpion008
                                #7 Quote Reply

                                  Should the wave be able to cut all wire to big for its scissors and to small for the hard wire cutters including stranded wire? Or should it be able to cut the finest wire as well? I hoped I wasn't abusing it by using it to cut a tiny screw (which it did cut), but even before that it couldn't cut the smushed piece of metal that held the beads on my sister's cheap necklace.

                                  1 Reply Last reply
                                  • bmot Offline
                                    bmot
                                    Posts: 4,468
                                    bmot Offline
                                    bmot
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @scorpion008 said:
                                      Should the wave be able to cut all wire to big for its scissors and to small for the hard wire cutters including stranded wire? Or should it be able to cut the finest wire as well?

                                      I heard they're able to cut paper, even, so fine wire shouldn't be a big problem. (mine doesn't, btw, but that's a second hand one, so I don't know how sharp they still are...)

                                      1 Reply Last reply
                                      • dks Offline
                                        dks
                                        Posts: 21,823
                                        dks Offline
                                        dks
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Was it like that when new or did it go loose after you cut a screw? Some metals,(like SS nails) can be very hard.

                                          Really, the dealer is your best bet. Obviously it is, now, damaged.

                                          1 Reply Last reply
                                          • scorpion008 Offline
                                            scorpion008
                                            Posts: 139
                                            scorpion008 Offline
                                            scorpion008
                                            wrote on last edited by scorpion008
                                            #10 Quote Reply

                                              Here's what I was cutting. I got even more play when I rolled this thin stuff up into a smaller piece. Like said, Christmas day, it couldn't cut some stranded wire with a small piece of metal smooshed around it. It bent like now. Also, I later tried moderately hard to cut a penny, but didn't try my hardest by any stretch of the imagination. Should small metal things be able to bend the massive pivot on a Wave or is it play that is not seen until pressure is exerted?

                                              rsz_dsc00001.jpg

                                              1 Reply Last reply
                                              • scorpion008 Offline
                                                scorpion008
                                                Posts: 139
                                                scorpion008 Offline
                                                scorpion008
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  Definitely more play than originally. There was none new. Do Waves develop play over time? (under a week?)

                                                  1 Reply Last reply
                                                  • dks Offline
                                                    dks
                                                    Posts: 21,823
                                                    dks Offline
                                                    dks
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      No.

                                                      See the seller/dealer for a repair.

                                                      1 Reply Last reply
                                                      • scorpion008 Offline
                                                        scorpion008
                                                        Posts: 139
                                                        scorpion008 Offline
                                                        scorpion008
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          Ok, I'll be returning it. LLBean does free shipping both ways and a brand new product guaranteed in such cases so it's just a time issue. I still have my old Sheffield wooden handled multi for now. When I get a new one, what is the maximum size for something the regular wire-cutters can cut? Should thin stranded wire (or anything else not a clean cut) be able to bend the huge pivot?

                                                          1 Reply Last reply
                                                          • Heirphoto Offline
                                                            Heirphoto
                                                            Posts: 62
                                                            Heirphoto Offline
                                                            Heirphoto
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              It sure sounds like this tool was defective as it should take a huge amount of force to displace the jaws like that on a new tool.

                                                              While usually favored over other thypes I do think bypass cutters are more likely to have this type if issue (if defective) though as anything that wedges between the blade now exerts a sideways force, wedging the pivots 90 degrees from the designed loading. It should not have happened anyway but if there was a workmanship issue this could do it.

                                                              Anvil cutters, while having their limitation do not force the jaws sideways, they either won't cut, won't close or will nick and deform but at least the load stays applied in the direction the pliers pivot, not 90 degrees to it.

                                                              Tony

                                                              1 Reply Last reply
                                                              • scorpion008 Offline
                                                                scorpion008
                                                                Posts: 139
                                                                scorpion008 Offline
                                                                scorpion008
                                                                wrote on last edited by
                                                                #15 Quote Reply

                                                                  @Heirphoto said:
                                                                  It sure sounds like this tool was defective as it should take a huge amount of force to displace the jaws like that on a new tool.

                                                                  While usually favored over other thypes I do think bypass cutters are more likely to have this type if issue (if defective) though as anything that wedges between the blade now exerts a sideways force, wedging the pivots 90 degrees from the designed loading. It should not have happened anyway but if there was a workmanship issue this could do it.

                                                                  Anvil cutters, while having their limitation do not force the jaws sideways, they either won't cut, won't close or will nick and deform but at least the load stays applied in the direction the pliers pivot, not 90 degrees to it.

                                                                  Tony

                                                                  Well put. So, does this mean that anything not cut (stranded wire, etc.) will force the jaws apart the wrong way? Because that sounds like a terrible thing to implement in a tool. In a non-defective tool, what do you think should happen when strong force is used on stranded wire (and the like)? Does one need to take precaution not to cut certain things?

                                                                  1 Reply Last reply
                                                                  • MultiMat Offline
                                                                    MultiMat
                                                                    Posts: 8,694
                                                                    MultiMat Offline
                                                                    MultiMat
                                                                    wrote on last edited by
                                                                    #16 Quote Reply

                                                                      It looks like you have damaged your **wire ** cutters mate, I think you are actually abusing the wire cutters by cutting pennys, screws & bullet casing. I think a lot of multi tools would be damaged by that abuse :think:. I think LM could easily say the warranty is null & void as what your doing is not what the tool was designed for , like I said they are 'wire cutters' not cut everything cutters.The bur you created will effect the pliers function + I think the abuse has caused the pliers to become deformed/distorted hence they are not lining up.

                                                                      Most(not all) modern Leatherman have a round cut out at the base of wire cutters designed for hard wire, your Wave has this(there are 2 arrows pointing too it) & they can cut nails if put into the hard wire notch but even then I would be super careful as you could damage the tool doing that.

                                                                      1 Reply Last reply
                                                                      • scorpion008 Offline
                                                                        scorpion008
                                                                        Posts: 139
                                                                        scorpion008 Offline
                                                                        scorpion008
                                                                        wrote on last edited by
                                                                        #17 Quote Reply

                                                                          Thank-you mate for the honest truth. I guess I expected to much of my tool. So, are the wirecutters only useful for cutting thin, non-stranded, flexible (not hard), wire (probably wrapped in rubber-plastic)? Would I be able to do a lot more with the Rebar head?

                                                                          1 Reply Last reply
                                                                          • Yak-er Offline
                                                                            Yak-er
                                                                            Posts: 23
                                                                            Yak-er Offline
                                                                            Yak-er
                                                                            wrote on last edited by
                                                                            #18 Quote Reply

                                                                              The standard cutters are for soft wire (copper, aluminum, etc) braided or solid strand. The hard wire cutters are for hard wire (steel mostly). The cutters in most mulititools are not nearly as durable as dedicated cutters. I try to avoid steel wire in my cutters unless that's all I've got. Screws are very hard, I would never try to cut them with any cutters, especially a multitool. An abrasive wheel is the best way to cut a screw, or just use the pliers to break it off.

                                                                              1 Reply Last reply
                                                                              • scorpion008 Offline
                                                                                scorpion008
                                                                                Posts: 139
                                                                                scorpion008 Offline
                                                                                scorpion008
                                                                                wrote on last edited by
                                                                                #19 Quote Reply

                                                                                  Here's my old multi. I have alot to learn about proper usage or wirecutters.

                                                                                  DSC00001.JPG

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Leatherman Tools
                                                                                  4. Broken Wave?
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0