CyberTool bitdriver metal
-
Has anyone besides me thought about this before?
I'm very tempted to pick up a CT34 so I have, of course, been spending quite some time just reading about them, looking at photos and so on. You guys know the drill I'm sure. 8)
Here's the thing.. the bit driver seems to darken compared to the rest of the tools.. any idea what causes that? It seems like it's not the same metal or at least not the same type of steel as the rest of the tools?
Here's an example for instance instance (and old thread by Syph007). You can clearly see that the driver is darker than the rest of the tool and I've seen this in person as well.
No big deal really as long as it's just a darkening I suppose but I'm curious to why it happens. Any ideas?
-
I'd suggest lower chrome/nickel content to avoid stress cracking on the internal corners means it's more liable to pick up a patina. Nothing to worry about though I'd say :)
-
@50ft-trad said:
I'd suggest lower chrome/nickel content to avoid stress cracking on the internal corners means it's more liable to pick up a patina. Nothing to worry about though I'd say :)Yeah I figured it was something like that. As long as I don't have to worry about it I don't mind some patina on it.
Thanks for the quick response!

-
Yes, my wife's Cybertool has a visible discoloration (~10 years of intensive use, never carried though, it is in a drawer it's entire life).
I tried the magnetic properties of my tool in the XLT (no discoloration yet, after 4-5 months of EDC and use) and it seems that there is low iron if any in it.
But it works anyway. Not a trace of disfigurement or malfunction. One may inflect the bits but not the cybertool.
It might be some chrome plated copper alloy perhaps? -
Mind sharing a picture of her CT? :)
-
Ya its not as nice of steel for sure. Its a cast part you can see the casting lines around it. No idea what the metal is though, and I have seen rust inside a used one. So it may not be as stainless as the rest of the SAK.
-
Here it is. In daylight the difference is easily distinguishable. I might post another one tomorrow.

-
Thanks mate. Pretty big difference between the tools there, but as long as it works I suppose.. :)
-
I suppose the bit driver is rather drop forged than cast, or at least i hope so. ;)
The metal is of different colour than teh SS tools because a different kind of steel is used, It´s a more elastic and tough steel that is not as brittle as the blade/tool steel.
Most likely the steel is less rust resistant than the other steel used in the knife and so is eitehr chrome or nickel plated to achieve a hard, corrosion resistant finish (like you would find on wrenches).
So most likely the quality is not "worse" but just different to achieve certain abilities. -
Here's a daylight photo

-
Polish it with Flitz and it will look like new in seconds.
-
That's a nice photo, thanks.

Yeah, I suppose it's not so bad, I might end up polishing it now and then just to make sure it won't start picking up rust. Doesn't seem overly common with them rusting though.
-
It doesn't look like rust. It seems that a coating is destroyed by rubbing with the hands (and sweat rich in fatty acids).
I don't know that Flitz product. I might try with something available here. What is it for?
We have a few polishing agents with easy names, Silvo for silver, Brasso for Brass, etc. what metal should I search for? -
Looks more like a very light oxide of some sort, but not rust. Mine is similar, but I always assume the metal was a little different to the main tools.
-
Ya its not rust. I polished mine the same way I do all steels and it took ok. Fine sandpaper and then a dremel with wool buff.
The rust I found on a used one was on the inside of the hex hole.
-
Not knowing a lot about metallurgy, my uneducated guess is it's probably got a higher carbon content in it to make it springier and therefore tougher than the stainless used in the other tools.
As for the magnetization thing, I haven't tried this myself, but there are small and high powered rare-earth magnets made as spacers for flat top li-ion cells used to act as positive terminals for those cells. I'd think a small one (link included below) might fit inside the bit driver to help hold bits in place.
I'll try and see if one will actually fit, and if I can figure out a way to easily get it back out, I'll experiment with it to see if it will actually work.
-
I have a Cybertool, from back when they were first sold in the US. It's been used steadily since I first got it. It lives on my desk at work. My driver shows no discoloration whatsoever. ???

-
They might have changed the material at some point.
-
@Buzzbait said:
I have a Cybertool, from back when they were first sold in the US. It's been used steadily since I first got it. It lives on my desk at work. My driver shows no discoloration whatsoever. ???
Maybe they switched to something cheaper to shave some bucks off of them?
There's just one solution..

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login