Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

SAK Assembler

Scheduled Pinned Locked Moved The Mod Squad
11 Posts 1 Posters 5.0k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. SAK Assembler
SAK Assembler
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • scibeer Offline
    scibeer
    Posts: 427
    scibeer Offline
    scibeer
    wrote on last edited by
    Quote Reply

      I originally put SAKs together "freehand" trying to get the layers to stay together while compressing springs and juggling tools. If you've ever tried it, you'll know how frustrating it can be.

      I made this jig to hold the pins steady as layers are added and wanted to share it here. The jig takes minutes to make and will simplify things a lot.

      Start with a piece of corian, sturdy wood, thick plastic, micarta or whatever you can find. Figure out the pin sizes you need for the mod and find drill bits just a hair larger than the pin diameter (I mean it! 1 or 2 thousanths over the diameter of the pin for best results)

      A decent set of fractional drill bits can be found at knifekits.com that has all the sizes you need and lots more for around $35

      Use one of the liners fro the SAK you're modding as a template for drilling the hole patterns into your SAK platform.

      Set the liner close enough to the edge so when you are assembling, you can use the edge of the platform as a pry point for your pliers for compressing the springs.

      Check out the pictures below and it should make sense.

      The tighter holes you drill and the deeper the hole you use, the stronger the system will be and the easier it will be to put the knives together.

      Here are some pin sizes and the drill bits I use that work well

      84mm SAK - uses 0.085in pins (2.25mm) - Drill holes that are .086-.088in about 7-10mm deep.

      91mm SAK - uses .085in pins for the inside pins and .098in (2.5mm) for the outside pins. Drill holes that are .086-.088in and .099-0.100in 10mm deep

      You will waste some brass pinstock by drilling the holes deeper, but its cheap and the other alternative is to drive yourself nuts until you start breaking things which is quite a bit more costly!



      1 Reply Last reply
      • Spoonrobot Offline
        Spoonrobot
        Posts: 1,894
        Spoonrobot Offline
        Spoonrobot
        wrote on last edited by
        #1 Quote Reply

          Right Click -> Select All -> Copy -> Save To Desktop.

          :)

          Thanks for the information! Althought I am probably quite a way from modding my own SAKs it's really cool of you to show some of the information you had to learn the hard way.

          1 Reply Last reply
          • Mike, Lord of the Spammers! Offline
            Mike, Lord of the Spammers!
            Posts: 42,975
            Mike, Lord of the Spammers! Offline
            Mike, Lord of the Spammers!
            wrote on last edited by
            #2 Quote Reply

              Great post mate, very informative :)

              1 Reply Last reply
              • Benner Offline
                Benner
                Posts: 28,081
                Benner Offline
                Benner
                wrote on last edited by
                #3 Quote Reply

                  Thanks for that Bill. :)

                  Very interesting.

                  1 Reply Last reply
                  • J-sews Offline
                    J-sews
                    Admin Team
                    Posts: 23,224
                    J-sews Offline
                    J-sews
                    Admin Team
                    wrote on last edited by
                    #4 Quote Reply

                      Very generous of you to share that Bill. I must admit not understanding what you meant about "using the edge of the platform as a pry point for your pliers for compressing the springs" but one glance at your photo and it all makes sense. :)

                      1 Reply Last reply
                      • Leatherman123 Offline
                        Leatherman123
                        Posts: 6,568
                        Leatherman123 Offline
                        Leatherman123
                        wrote on last edited by
                        #5 Quote Reply

                          Thanks Bill!

                          1 Reply Last reply
                          • Neil Offline
                            Neil
                            Posts: 15,287
                            Neil Offline
                            Neil
                            wrote on last edited by
                            #6 Quote Reply

                              Cheers Bill. Thanks to seeing your jig over on SOSAK I never had to go through the frustration of using clips and clamps for my first mods. The first thing I did was make a jig.

                              So thank you for the hours and blood saved :cheers:

                              Neil

                              1 Reply Last reply
                              • scibeer Offline
                                scibeer
                                Posts: 427
                                scibeer Offline
                                scibeer
                                wrote on last edited by
                                #7 Quote Reply

                                  I'm glad it was useful to someone.

                                  I bled plenty for the both of us my friend!

                                  1 Reply Last reply
                                  • porteiro Offline
                                    porteiro
                                    Posts: 106
                                    porteiro Offline
                                    porteiro
                                    wrote on last edited by
                                    #8 Quote Reply

                                      I know this is an old thread, but...

                                      Once you have the knife assembled on the jig, how do you then transfer it to the pins that have one end peened over?

                                      Or do you peen over the pins in place in the jig?

                                      1 Reply Last reply
                                      • scibeer Offline
                                        scibeer
                                        Posts: 427
                                        scibeer Offline
                                        scibeer
                                        wrote on last edited by
                                        #9 Quote Reply

                                          The pins I assemble the knife on in the jig are the pins I peen. I don't flatten out one side first. Both sides are normal pinstock when I'm done assembling. I pull the knife off the jig (carefully!) and peen each side after trimming and grinding the pins to the correct length with pliers and a dremel or belt sander.

                                          Rest one side of the pins on a piece of metal or little anvil of some kind to peen against. Does that help?

                                          1 Reply Last reply
                                          • porteiro Offline
                                            porteiro
                                            Posts: 106
                                            porteiro Offline
                                            porteiro
                                            wrote on last edited by
                                            #10 Quote Reply

                                              Yes. That's exactly what I wanted to know. :)

                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              1. Home
                                              2. Tool Talk
                                              3. The Mod Squad
                                              4. SAK Assembler
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0