Squirt modification
-
bit off topic,sorry:
hey zepla,whats that little tolkit u have there with wrenc,sockets,bits etc?
looks delicious.
SO,where to get a hold of those ?
-
That's a Teng Tool set. (www.tengtools.com) They make excellent tools for reasonable prices and have exactly what I need, like that set you see at the pictures. It is very small but has just what I regulary need for my work. Most of my other tools are from Teng as well. An even smaller set and a bigger set. (no, I don't have stock options in that company ::) )
Funny thing was the first time I had seen this stuff I tought it was just chinees made crap. What did you expect with a name like that
But when I looked closer it looked quit good to my surprise. I did some research and now I know it isn't chinees and comes with a sort of lifetime warrenty and if I need some tool I'll buy Teng. (It helps when you have Teng dealer around the corner in my case.) -
oh its a teng? im familiar to them,at fisrt when i saw your pic i looked at that mini ratchet that looked like ones teng sells.they dont sell tengs here,do u know one in uk(us who sells em ,maybe even overseas.
ive seen those in sweden,just couple weeks ago while i was on large motorcycle happening,teng had a small....tent there and they had set that held some 5 sockets,that ratchet,and some bits,intended for motorcycle use.i looked at that sam kit at 2007 too,but that happening is sooo hot and i have to get lots of beer to avoid dehydration ;),and that stuff eats my wallet.
-
You can try spot anealing the area you want to drill with a soldering iron. I've done it before with marginal results. I was able to drill a hole with a cobalt bit, but the bit was history afterward.
A carbide bit is about the only equalizer for hardened steel. pm me and I can help you get a few for a lot less than the normal $15 or so each.
-
@ Tarrodemierda, I have that smaller set you mentioned as well. Very handy little set!
@ Scibeer, at the moment I just need to drill a hole in a piece of spring steel. It is less than 1mm or so thick. With a normal drill I should go through it, I guess. I just have nothing in the house at the moment. That will be sorted today or at least this week. But thanks for the offer to help anyway!

The really big problem will be drilling a hole in the spyderco knife that is comming my way. That is thick and really hard! The hole I've made in the current spyderco blade took me twee weeks!
-
It's not soft stuff, is it?
I have a great collection of burnt up drill bits being used as punches!
-
@kent ct said:
You need slow speed to drill steel. Can not be done with Dremel unless you use carbide bit. Why not soften steel? You can then do all your shaping and when done re-harden and temper.
Richard
I think harden and temper steel is a bit beyond us ordinary folks. :o
We are only talking about a small piece of high carbon spring steel of uniform thickness. It only gets tricky when the steel is not uniform in shape. Also this is not stainless steel which work hardens if not drilled carefully. Another approach to putting a hole in spring steel is to put the steel on a piece of wood and center punch it where you want the hole. this will make a dimple in the steel. Turn it over and file the projecting dimple off. You will be left with a small hole that you can follow up with the drill. The drill will bite much more easily. Also drill with the spring on a piece of wood and clamped down to avoid it spinning around when the drill breaks through.
To open the tang hole on a blade you might consider honing it open if if does not need very much. Valve grinding compound and copper or brass as a hone.
Richard
-
The center punch approach sound like a good idea! Once you have a little hole or even a dimple drilling would be much easier indeed.
And making a hole in a blade just a bit bigger is not so difficult with the dremel (not even for me :D). But making a new hole is a problem in my experience :ahhh I went with the balde I have now to a blacksmith and even he couldn't make a hole in it! I'm not looking forward to go over that procedure all over again. That VG-10 steel is really, really tough! Why oh why does my squirt not come standard with a proper knife ::)
-
@zepla said:
The center punch approach sound like a good idea! Once you have a little hole or even a dimple drilling would be much easier indeed.And making a hole in a blade just a bit bigger is not so difficult with the dremel (not even for me :D). But making a new hole is a problem in my experience :ahhh I went with the balde I have now to a blacksmith and even he couldn't make a hole in it! I'm not looking forward to go over that procedure all over again. That VG-10 steel is really, really tough! Why oh why does my squirt not come standard with a proper knife ::)
To drill the blade. Two carbide drills, preferably spade bits, not twist drills which are weaker. One drill one half the size of the hole you want and the other one the finish size. Use a bit of bacon fat as cutting oil. If someone has tried to drill the blade and failed, that spot will be even harder as it will be work hardened.
Richard
-
@kent ct said:
The center punch approach sound like a good idea! Once you have a little hole or even a dimple drilling would be much easier indeed.
And making a hole in a blade just a bit bigger is not so difficult with the dremel (not even for me :D). But making a new hole is a problem in my experience :ahhh I went with the balde I have now to a blacksmith and even he couldn't make a hole in it! I'm not looking forward to go over that procedure all over again. That VG-10 steel is really, really tough! Why oh why does my squirt not come standard with a proper knife ::)
To drill the blade. Two carbide drills, preferably spade bits, not twist drills which are weaker. One drill one half the size of the hole you want and the other one the finish size. Use a bit of bacon fat as cutting oil. If someone has tried to drill the blade and failed, that spot will be even harder as it will be work hardened.
Richard
Here is what you need. From traverstool.com

-
Bacon fat, hmm. I check check the fridge. There goes my lunch.... :(
-
@zepla said:
Bacon fat, hmm. I check check the fridge. There goes my lunch.... :(Next time you have bacon and eggs just pour off the fat into a can. At room temperature it will harden. Dip your drill in the can and go to work. Lard oil was the preferred cutting oil for drilling for many years.
Richard
-
So you are not kidding then ??? :D Can't I just use a bit of WD-40? I'll look if my local hardware store has the carbide drill in stock...
-
dont use any wd-40,its not for cutting.use proper tapping & cutting oil.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login