Leatherman MINITOOL Mod Possible???
-
I know it is possible to fit the (I think is the Wave) Small Bit Adapter into it with no modification:
http://s947.photobucket.com/user/FenixArcher/media/IMG_9515_zps9j0wk9l6.jpg.html
But would be possible to mod with the phillips driver of a PST or PSTII (i know they are different)...?

Are they too long for this?
The notch is the same for the 3 tools I suppose.
Perhaps bending the driver would fit in the MINI

Thanks!

P.S.: I am interested in a Mini TOOL with flat and phillips driver (perhaps I would change the file flat original driver for another more resistent of a PST or PSTII too
-
G'Day,
I don't have a Mini-tool, but had a look at the LM website. They state the blade is 3,81 cm long (1.5"). I don't know how much more will be added to measure the total length of the blade. I measured the lengths of two PST phillips drivers I have: the older style that works towards the middle of the tool when opened measures 5cm in total length and 4,5cm from tip to the middle of the pivot; the newer style phillips measures 4,5cm total length and about 4cm from the middle of the pivot hole to the end. It is difficult to say without having the tool at hand whether they will fit, my guess is No to long.
A medium PST flat driver measures 4,5cm total length for the old style driver and 4 cm for the new style driver, they may be an easier fit, subtract 5mm for the length from the middle of the pivot to the end of the driver.
One other thing you need to keep in mind is where the pliers will sit when closed and whether it will rub against any of the tools added.
Cheers,
Pete
-
Thank you very much Pete

-
Probably be a no go :( I was looking at one of my :ahhh :ahhh :ahhh MINI's :ahhh :ahhh :ahhh and the plier head just doesn't leave any room whatsoever IMO for any other tools (the swap out for another flat head would be possible but I don't think even if bent the phillips head would work) :-\ Would be awesome if there was any room to add anything else though
If you do try it and I am wrong please share some pics cause that would be awesome :D -
G'Day,
Got my Mini-tool today, an unintentional purchase. ;)
I have not dismantled the tool, and will probably not in due course. But, did a few comparisons. There is no way a Phillips from a PST or PST II will fit in. The head is to wide to fit in next to the plier head. Length is OK though. One can possibly remove some material from the outer "sleeve" but that will compromise the integrity of the handles.
On the other hand it looks like a medium or large flat head will fit. Length wise it is not a problem and width wise looks fine too. The only other issue might be the back of the tool and opening mechanism. That can only be verified with the tools out. The nail nick might be on the wrong side too.I have a few shots just to show the length, width is a little more tricky. I hope this helps.
Cheers,
Pete
-
MAybe you could fit in the 2D Phillips out of a Wingman/Sidekick or from one of teh Gerbers with 2D Phillips?!
-
If that Phillips head only likes a little bit then perhaps you could grind it down closer to a 2D version

I am actually surprised that it is that close to fitting :o Perhaps there is hope of a mod after all :ahhh :ahhh :ahhh
:D -
@lowtech said:
MAybe you could fit in the 2D Phillips out of a Wingman/Sidekick or from one of teh Gerbers with 2D Phillips?!Not without some major grinding. The Sidekick/Wingman Phillips, while thinner than the 3D Blast/Fuse/Kick/Rebar Phillips, is still a fairly thick tool. If the PST phillips is comparable in size to the SOG Phillips, it would be about 1.5 times too thick.
And won't most Gerber Phillip's drivers have too little in the pivot area to "catch" the minitool's spring?
-
I am not sure, I have not seen a dissected Minitool. I was just thinking out loud.
-
I have received a PST 3d phillips, I think it is possible to file it to 2d phillips like in a Micra...

-
-
I'm trying to make the bottle opener from the micra work, I think with the right washer I can get it to work.
Sent from my SAMSUNG-SM-N920A using Tapatalk
-
I have received a PST 3d phillips, I think it is possible to file it to 2d phillips like in a Micra...

From the picture above it does look doable :o
Pics if you can get it to work
:DWhat you cannot see in the pic is that the driver hides the "inner" handle of the Mini-Tool. If you start grinding you will have to make if flat like the Micra one.
Micra one may fit, but I think that you will have to make the pivot hole bigger and space it with a washer or two.
Pete
-
I have received a PST 3d phillips, I think it is possible to file it to 2d phillips like in a Micra...

From the picture above it does look doable :o
Pics if you can get it to work
:DWhat you cannot see in the pic is that the driver hides the "inner" handle of the Mini-Tool. If you start grinding you will have to make if flat like the Micra one.
Micra one may fit, but I think that you will have to make the pivot hole bigger and space it with a washer or two.
Pete
Yeah I gotcha now
I wasn't thinking about the other part of the handle in there 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login