Skip to content
  • Categories
  • Recent
  • Popular
  • World
Skins
  • Light
  • Dark

Collapse

NodeBB

Pin Sizes

Scheduled Pinned Locked Moved The Mod Squad
13 Posts 1 Posters 12.7k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • C
    C
    Craig T
    wrote on last edited by
    #1

    I am preparing to mod a SAK Outrider and have been looking for the pin sizes. This is almost certainly often repeated info. I have been searching but have not found the answer.

    This is listed in "A "how-to" for basic SAK mods"
    91mm: 2.5mm outer, 2.2mm (2.25) center
    84mm: 2.25mm for all
    74mm: 2mm modern, 1.5mm older
    58mm: 1.5mm

    The Outrider is 111 mm. Are 91mm and larger all the same pin sizes?

    Also, what the favorite sources for brass pins stock?

    Sorry if these are often asked annoyingly simple questions. Sometimes I just don't seem to find info that other folk find easily.

    As always, any input is most appreciated.

    1 Reply Last reply
    0
    • jaya_manJ
      jaya_manJ
      jaya_man
      Global Moderators
      wrote on last edited by jaya_man
      #2

      111mm liner lock models follow the 93mm pin sizes, ie: 3mm outer and 2.5mm inner.

      111mm slide lock models follow the 91mm pin sizes...

      Info can be found in this thread:

      /topic/48172

      I think it is also part of the list of mod guides in the sticky section under The Mod Squad.

      Sent from my iPhone using Tapatalk

      1 Reply Last reply
      0
      • C
        C
        Craig T
        wrote on last edited by
        #3

        Thanks jaya_man for the info and thread link. Very helpful info.

        If I decide to proceed with adding parts from a 111mm liner lock (3 / 2.5mm pins) into the Outrider 111mm slide lock (2.5 / 2.2mm pins) I will need to drill out the Outrider components.

        What type of drill bits have you folk found to do the best job at drilling the hard steel? High speed steel? Carbide tipped? Solid carbide? Carbide straight flute?

        Has anyone gone in the other direction and put a bushing in the 3mm holes to reduce to 2.5mm?

        1 Reply Last reply
        0
        • jaya_manJ
          jaya_manJ
          jaya_man
          Global Moderators
          wrote on last edited by
          #4

          No worries...

          My only experience is using HSS bits (waisted a lot) for reducing pivot hole size on 91mm scissors so that I can implant them on 84mm...

          As there is not much difference between 2.5mm and 2.2mm, first had to enlarge it to 3mm, stuff the hole with brass, then redrill 2.2mm hole...

          I have yet to find carbide bits [emoji16]

          Sent from my iPhone using Tapatalk

          1 Reply Last reply
          0
          • sLaughterMedS
            sLaughterMedS
            sLaughterMed
            wrote on last edited by
            #5

            Honestly, I havent had any trouble with holes that were .5mm larger than the pins they rode on. Heck, Victorinox even uses the 93mm awl and pruning blade on the XAVT, with 3mm holes, and 2.5mm pins! I test fit everything with the 2.5mm pins, and see if everything works correctly, because honestly, drilling those pivots and springs out is a huge pain in the ass, especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

            @jaya_man said:
            I have yet to find carbide bits [emoji16]

            Do you have Amazon where you live? There are lots of options for carbide drill bits on American Amazon

            1 Reply Last reply
            0
            • jaya_manJ
              jaya_manJ
              jaya_man
              Global Moderators
              wrote on last edited by
              #6

              @sLaughterMed said:
              Honestly, I havent had any trouble with holes that were .5mm larger than the pins they rode on. Heck, Victorinox even uses the 93mm awl and pruning blade on the XAVT, with 3mm holes, and 2.5mm pins! I test fit everything with the 2.5mm pins, and see if everything works correctly, because honestly, drilling those pivots and springs out is a huge pain in the ass, especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

              @jaya_man said:

              I have yet to find carbide bits [emoji16]

              Do you have Amazon where you live? There are lots of options for carbide drill bits on American Amazon

              Have yet to have an amazon account... still searching local distributors

              Sent from my iPhone using Tapatalk

              1 Reply Last reply
              0
              • PTRSAKP
                PTRSAKP
                PTRSAK
                wrote on last edited by PTRSAK
                #7

                I have been using carbide drills like these for drilling blade/tool/spring pin holes

                http://www.ebay.com/itm/271627790645?

                They really need to be used in a drill press, very brittle and shatter if you try to use them in a hand drill and put any side load on them.

                1 Reply Last reply
                0
                • hiraethusH
                  hiraethusH
                  hiraethus
                  Admin Team
                  wrote on last edited by
                  #8

                  Good info here. :like: I'll add a link to this topic to the SAK modding guide sticky post: /topic/43303

                  1 Reply Last reply
                  0
                  • shibafuS
                    shibafuS
                    shibafu
                    wrote on last edited by
                    #9

                    @sLaughterMed said:
                    especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

                    I've sometimes had a ratio closer to the other way around, 2 bits ruined for 1 hole! Drilling out a hole to a slightly larger size is hell for twist drills because all the load is on the corners of the bit and they go blunt so quickly. Solid carbide reamers are the business šŸ™‚ The first time I tried one, it went through the stainless steel with so little resistance that I thought I'd forgotten to tighten the chuck!

                    1 Reply Last reply
                    0
                    • sLaughterMedS
                      sLaughterMedS
                      sLaughterMed
                      wrote on last edited by
                      #10

                      @shibafu said:

                      @sLaughterMed said:
                      especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

                      I've sometimes had a ratio closer to the other way around, 2 bits ruined for 1 hole! Drilling out a hole to a slightly larger size is hell for twist drills because all the load is on the corners of the bit and they go blunt so quickly. Solid carbide reamers are the business šŸ™‚ The first time I tried one, it went through the stainless steel with so little resistance that I thought I'd forgotten to tighten the chuck!

                      Too bad carbide doesn't play nicely with hand drills

                      1 Reply Last reply
                      0
                      • proletenstahlP
                        proletenstahlP
                        proletenstahl
                        wrote on last edited by
                        #11

                        @Craig T said:
                        I am preparing to mod a SAK Outrider and have been looking for the pin sizes. This is almost certainly often repeated info. I have been searching but have not found the answer.

                        This is listed in "A "how-to" for basic SAK mods"
                        91mm: 2.5mm outer, 2.2mm (2.25) center
                        84mm: 2.25mm for all
                        74mm: 2mm modern, 1.5mm older
                        58mm: 1.5mm

                        The 84 mm long nail file uses a 1.7 mm pin.

                        1 Reply Last reply
                        0
                        • L
                          L
                          LSUisSEC
                          wrote on last edited by
                          #12

                          What pin size for the 91mm huntsman?

                          1 Reply Last reply
                          0
                          • SAKTaschenmesserS
                            SAKTaschenmesserS
                            SAKTaschenmesser
                            wrote on last edited by SAKTaschenmesser
                            #13

                            @LSUisSEC said:
                            What pin size for the 91mm huntsman?

                            As original post 2.5mm and 2.2/2.25mm.

                            I might be wrong, but I’m under the impression that 2.2 or 2.25mm brass rod is harder to find in the USA than Europe.

                            Sent from my iPad using Tapatalk

                            1 Reply Last reply
                            0

                            Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                            Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                            With your input, this post could be even better šŸ’—

                            Register Login

                            • Login

                            • Don't have an account? Register

                            • First post
                              Last post
                            0
                            • Categories
                            • Recent
                            • Popular
                            • World