Sharpening Methods
-
Most of the time I use the dual sharpener... sometimes use the Spyderco Sharpmaker when the blade is really dull (usually for purchased second hand SAKS and for sharpening scissors)... In either case, I use a leather strop afterwards...
Sent from my iPhone using Tapatalk
-
I use the Sharpmaker at 40° with the fine and sometimes ultra-fine stones (medium as necessary for a duller blade). But I'm no expert by any stretch, it's just what I can do that works. The resulting edge will slice through phone book paper with ease, that's good enough for me.
-
I use the dual sharpener. It works especially well on sak and also works on leatherman.
However, I found it more useful on larger blades like 91mm. I always have difficulties on sharpening the front part of small blades like the 58mm blades. I can sharpen the latter part of the blade razor sharp but the front part is usually... OK sharp...
Anyone have some good tips on doing the tip of small blades? -
@aurabattler said:
I use the dual sharpener. It works especially well on sak and also works on leatherman.However, I found it more useful on larger blades like 91mm. I always have difficulties on sharpening the front part of small blades like the 58mm blades. I can sharpen the latter part of the blade razor sharp but the front part is usually... OK sharp...
Anyone have some good tips on doing the tip of small blades?The dual sharpener should do the trick... just focus on the tip and mantain a constant angle... stropping afterwards will make it even better
Sent from my iPhone using Tapatalk
-
I use the Lansky clamp system with the guide rods. It is the only way I'm able to be consistent on the angle. I like it a lot.
-
@metasyntax said:
I use the Sharpmaker at 40° with the fine and sometimes ultra-fine stones (medium as necessary for a duller blade). But I'm no expert by any stretch, it's just what I can do that works. The resulting edge will slice through phone book paper with ease, that's good enough for me.I'm no expert at sharpening, but have also been using a Spyderco Sharpmaker at 40° (on the flat side of the rods) with the fine rods, as it's the only way I've found that I can get a reasonably consistent angle and seems to avoid causing unwanted micro serrations and also doesn't scratch rest of the blade up. Metasyntax - do you find the ultra-fine rods work well and give an extra level of sharpness? Have been considering getting a pair, but they're quite expensive. Have also recently acquired a basic wood-mounted leather strop and some Smurf Poo stropping compound, but haven't tried this out yet, will experiment on some "user" knives.
-
I use the Sharpmaker at 40° with the fine and sometimes ultra-fine stones (medium as necessary for a duller blade). But I'm no expert by any stretch, it's just what I can do that works. The resulting edge will slice through phone book paper with ease, that's good enough for me.
I'm no expert at sharpening, but have also been using a Spyderco Sharpmaker at 40° (on the flat side of the rods) with the fine rods, as it's the only way I've found that I can get a reasonably consistent angle and seems to avoid causing unwanted micro serrations and also doesn't scratch rest of the blade up. Metasyntax - do you find the ultra-fine rods work well and give an extra level of sharpness? Have been considering getting a pair, but they're quite expensive. Have also recently acquired a basic wood-mounted leather strop and some Smurf Poo stropping compound, but haven't tried this out yet, will experiment on some "user" knives.
The superfine stones should make the edge smoother... and the strop will even make for much smoother cuts apart from giving the edge a mirror finish...
Sent from my iPhone using Tapatalk
-
A couple of years ago, after a fair bit of reading around here and elsewhere, I picked up the Spyderco Sharpmaker to use instead of my primitive Victorinox Sharpy. I have used both angles but tend to go with the 40.
I regard myself as around beginner at sharpening. Yet I do not need to be able to shave with a knife (though this is fun to test). My knives are sharpened to the point of cleanly cutting paper but more is overkill and perhaps best avoided with kids around anyway.
-
95% of the time I use 12 micromesh mx 12x4 inch sheets and sharpen by hand from 80mx to 1200mx that's the most relaxing as you can watch TV at the same time :)
I also have
Wicked Edge .... Quick review Fantastic bit of kit and if I was to sharpen a $1000 knife I would use it every time ..... But it is a bit of a space hog on my desk so it rarely sees daylight
Spyderco Sharpmaker ..... Great ......I also got the diamond rods and superfine (but to be honest I don't think they are worth the cost )
Work Sharp Ken Onion Edition with knife grinding attachment ..... total overkill for sharpening but having a mini belt grinder on my desk is very handyI have tried a few other systems but sold them on mostly if they were a pain to set up or use
-
Lansky system if the blades fit (the pen blades are a bit small, particularly on the fatter SAKs) to set the angle, then a Turnbox for maintenance. I keep a Vic dual sharpener handy for touching up edges too.
-
I use the Sharpmaker at 40° with the fine and sometimes ultra-fine stones (medium as necessary for a duller blade). But I'm no expert by any stretch, it's just what I can do that works. The resulting edge will slice through phone book paper with ease, that's good enough for me.
I'm no expert at sharpening, but have also been using a Spyderco Sharpmaker at 40° (on the flat side of the rods) with the fine rods, as it's the only way I've found that I can get a reasonably consistent angle and seems to avoid causing unwanted micro serrations and also doesn't scratch rest of the blade up. Metasyntax - do you find the ultra-fine rods work well and give an extra level of sharpness?
The superfine stones should make the edge smoother... and the strop will even make for much smoother cuts apart from giving the edge a mirror finish...
^^ What he said. It certainly polishes the edge more, but in my experience doesn't improve cutting performance too much. Normally, I just do the fine stones and that's it. The ultra-fine stones are just for fun.
-
I like the Victorinox sharpener pen, when on the move. At home I'm using an Arkansas whetstone or the DC4. With the latter I keep my Pioneer Solo sharp enough to shave the hairs of my arm, and it doesn't take more than a minute (it's a weekly routine). I'm not using a strop, enough is enough. No pics as my camera is malfunctioning.
-
Very old butcher steel I bought 30+ years ago at a flea market. It has been my main knife sharpening tool since I was about 13 years old.


-
I also use the Lansky guide rod system but use a coarse stone, 3 Arkansas stones (soft, hard and black hard) and then a sapphire stone for final polishing. I also use the Lansky leather strop that uses the guide rods since I'm already set up. Yellowstone compound goes on the strop. I use 25 degree (50 degree inclusive) for all of my knives so I don't have to remember which angle goes to which knife. This system puts a very fine razor edge on the knife that shaves hair easily.
For ocassional touch-up I use the Lansky Fold-A-Vee also set at the 25 degree angle. Kind of like a fold up crock stick. Don't believe they are available now but some old stock still exists and they show up on eBay at times. I found a source for someone in the UK, evidently they are very popular with soldiers over there.

-
First step. If the blade has chips, dings, or other damage, I use a pretty coarse stone made by Lansky for sharpening garden tools to remove that damage.
Step two: I have a black stone, intended for sharpening axes, and of some synthetic material (carborundum) that's pretty fine, but not as fine as my Arkansas stone to "get a good edge".
Step three: Get a sharp edge with my Smith's Soft Arkansas soapstone.
Step four: Get a shaving sharp edge by stropping with a piece of cardboard, which I lay flat.
-
For someone that is not accustomed to sharpening and/or doesn't have the patience or spare time to learn freehand (stone) sharpening, I believe that the Spyderco Sharpmaker is about the best you can get. It's simple and easy to use, works well, and works on all sorts of different blades of all lengths, and you can even use it as a makeshift bench stone if you wish. It's my favorite "system."
That said, I'm currently using freehand sharpening much more than my sharpmaker. I'm currently using a medium coarse Smiths brand diamond stone or the unglazed ring on the bottom of a ceramic coffee mug, depending on what's closer to hand. It's not that difficult once you get the hang of it, but it does take practice. What I would do is find a cheap, junky, not good for much else knife and practice, practice, practice. You'll learn pretty quick how to get a working edge on a knife. Also, don't worry too terribly much about angles. As long as it's consistent between strokes, you'll get an edge. Just don't let it be too thin or it'll chip under heavy use, and too thick will tend to be blunter than you'll want. Victorinox uses 15 degrees per side iirc, and "my angle" (the one I naturally put on all the knives I sharpen on a stone) is probably around 15 or 20, which is a good all-purpose angle for the work I do.EDIT: It's worth noting that I prefer coarser, "toothier" edges on my knives, which is why the medium diamond and coffee mug bottom work for me as primary tools. If you prefer smoother edges, you'll need more stones, and those stones will need to be finer grit to give you that smooth edge. For me, toothy edges hold up better, are easier to maintain, and cut just as well for the work I do. It's personal preference.
Hope this helps. Good luck!
-
Whetstone and some rods.
:) -
+1 for sharpmaker
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

:D SharpMaker 8)