30D Traditional challenge
-
The holidays are a time for tradition. So what better way to celebrate them than with the traditional folder challenge.
So to kick this off I'll be starting with a Rough Rider camper. This knife has all your traditional features of a camping knife from the 40s and 50s; main blade, can opener(british type), bottle opener/screwdriver and an Awl. The traditional look is completed with a lanyard bail, polished bolsters and jigged bone.I will probably be switching this one out for some of my other traditionals during the course of this challenge. And as always I will be trying to pick up secondary badges along the way.


-
Can't wait for this thread Noa

-
Day2
Another Rough Rider, this time it's the pliers. This model is a non-standard electricians knife sporting short strip&screwdriver blade and a small pair of pliers w/ wire cutter notch.
-
Cool one !

-
Question
Is it a nail breaker :D I had one similar to that out at a store looking at it and it was either that one or the Electrician knife that was very hard to open :ahhhSweet pic though

-
It is tight but the camper is the nail breaker. The notch doesn't have a crisp cut eather, its tapered and polished so your nail slips.
I will do a close up with tomorrow's pics -
@Noa Isumi said:
It is tight but the camper is the nail breaker. The notch doesn't have a crisp cut eather, its tapered and polished so your nail slips.
I will do a close up with tomorrow's picsThanks buddy

-
Day3
As promised here's a study in opening and closing. I imagine the best way to measure these knives would be to clamp both knife and blade then pull open using a spring scale. Since I don't have that kind of a setup available at the moment I will be simply pushing the knife shut from 90 degrees on a kitchen scale. This should produce similar results as the back spring applies equal force in either opening or closing. For consistency I will be aiming for the center dot on the scale, holding the blade roughly at where a nail Notch would be (some of them don't have it) and the reading is the highest that I catch by eye. This should be the hump point of the knife where it's most likely to either slip or snap your thumbnail.Rough Rider pliers 460g
Queen Cutlery Big Chief 930g
Rough Rider camper 1024g
SOG mini Auto clip 144
IK co 1040g
unknown Pakistan 370g
Victorinox Trekker 280gI've also included a close up of the nail notch on the screwdrivers of both the RoughRider camper and the Victorinox Trekker. As you can see the Trekker notch is cut a little bit deeper and at a sharp 90-degree on the inside edge. The RoughRider is a little shallower and you see the vertical scallops. The RR's top edge instead of being 90° like the Victorinox is polished slightly round making it harder to grip. If you press your thumb across both nail notches the fleshy part of your thumb will actually catch on the Victorinox but not on the Rough Rider indicating that high polish and the slickness inside the nail nick.
Edit:
Correction I just caliper the thickness of the nail nick on the Roughrider camper screwdriver and the Vic and they're both read the same. So I guess it's just the polish that makes the Rough Riders slicker


-
Over 1 kg? Does that mean the RR Camper is a nail breaker?
-
I would say yes. I have never broken a nail on it, but it is not a pleasent opener. You are more likley to slip and have it snap shut on you. The blade is actualy the easiest tool to open on the RR Camper if you can believe it. That awl is a nightmare.
It kind of reminds me of my first knife in that respect. I don't even remember where I got it, but somehow I ended up with this knife I could barely open when I was about 6 or 7. I had it for all of a day before my old man caught me with it and took it away.
Then he gave me an Imperial Camper HOBO. That knife was a better fit and I carried it every day and for Scouts till it was stolen at Custaloga Town when I was 12. I actually just "replaced" it ( nostalgia trip) last year with an Imperial Camper Matterhorn that I found at a local pawn shop. -
That is a lot of pressure :o :ahhh
-
Day 4
Can opener time
The RR Camper uses a blade style opener that many sellers mistake as a small blade with them stuff when listing it. Though this type is common on older knives and as an independent kitchen utensil; the only reference I've ever seen to this type that gives it a name calls it a "British tin opener"
Now this type of opener can really cut all the way around; usually you only end up cutting halfway Around the can and then pouring the contents. Also you can't punch it too close to the rim or else you'll punch through the side of the can.I will try to add that can opener chart as soon as I find it I'm not sure where I put the pic



-
Interesting about that style can opener :o

-
Day 5
This zip tie project is something I did at work about a year ago. (Pics however are new) The top shelf is 2 pieces of scrap shelving that I cinched togeather with zip ties, then lashed with 300# bank line. This has been done and 6 locations where the two small racks overlap.The boss was suposed to bolt them together and never did. It has held up suprisingly well. Average load on this is around 180#

-
Great fix
and great to see that it has held up 
-
Day6
Painting. I'm going to be moving to a new place at the end of January; so I'm trying to get a head start some things like putting the accent walls back to being white.

-
:ahhh How did I miss this.
good thread Noa Isumi
-
Good luck with painting
Hope that the move goes smoothly for you and that you get the place you are at now in tip top shape 
-
Day 6
Big Chief
Today we're taking a look at the QueenSteel #45 "BigChief". This is a large 4in blade single jack knife with a unique solid cast aluminum handle patented in the 1955(?). Because of this solid cast handle, the tail of the backspring passes through a cutout to catch onto the back of the handle allowing the pivot pin to be the only pin. This means the knife has a total of 4 pieces; handle, blade, backspring, pivot pin.
From what I understand these were produced at QueenCutlery of Titusville PA in the '60s & '70s. Queen is still in buisness producing small run, high quality traditionals.
This is one of the 2 Queens in my collection; the other bieng a fixed blade hunting knife (#82 I think). I heard they stopped making fixed blades in the early 90s, but never verified; so I could be wrong.



-
I haven't seen a queen like that in ages, very unique piece.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
