Removing the keyring/lanyard loop.
-
I watched some youtube vids and read some forum posts regarding the removal of the keyring loop from Alox saks. The general recommendation for protecting the scales while filing off the loop is to apply some masking tape. I tried this and found that masking tape provides close to zero protection from a rough file. One slip, and you make a mess of the scales. This is partly my fault, as I always start a job with good intentions of being careful, but then get impatience and make mistakes. So I tried to come up with a foolproof solution.
Shim steel.

Masking tape first

Then a strip of shim steel on either side of the loop.



Carelessly file with a large smurf file.

Polish with dremel type tool.

Someone with more patience and talent than myself would not need to go to this extra trouble, but it was nice to know there was pretty much no way I could mess this up.


Edit 'smurf file' = Forum censored the term used for a 'rough' file.
-
Well done, thanks for sharing the pics.

What do you mean, "more patience and talent"?! Dude, most folks here just yank the damn thing apart with some pliers!

-
Great job

I did same to my Pioneer X, also shielded the area with thin steel.
My major concern even more than the shielding itself was to tape off the area so no metal shavings would get in there, it takes forever to cleen them afterwards.
The alox modeles, especially Pioners are 5ye hardest to grind the loop off. I usually cut the max i can with cuters then file the rest off.
Yours look a lot better trust me...
-
Clean job

A thinner file also helps, I used the one on my ps4.
Metal shims are a good idea though. The reusability factor is handy, especially if you’re like me and file off the irksome nub of every SAK you come across. >:D -
Nice work, lemo!

-
-
At present time, all of my SAKs are (excepting added mini screwdrivers and straight pins) unmodified. This is a good tip for those who don't wish to have the split ring attachment point, though.
"Smurf file" had me scratching my head. Was that UK terminology I hadn't heard before? Then I got to the end of the first post. I would have understood immediately if the filter substituted the word "illegitimate," but "smurf file" sounds a lot funnier.
-
Very nice job chap. I found opening the bottle opener on a cellidor model is handy as it makes the keyring tab sit up far enough you can get at it easier without damging the scales
-
Very well done. -
But now the loop won't poke you in the hand. See - you never thought of that did you?
-
This is a great idea!
I don't have shim steel, but I imagine that a few layers of aluminum cut from a soda can would work almost as well. -
@MacGyver said:
My major concern even more than the shielding itself was to tape off the area so no metal shavings would get in there, it takes forever to kleen them afterwards.I usually put blu tack / prestic in between the parts, then a few layers of masking tape. The blu tack usually captures all the shavings and very few if any gets into the knife itself. The first one I ever did was only masked off and the awl is still not quite factory snap. The subsequent Pioneer X got the blu tack treatment and all the tools snap as the day it left the factory.
Pete
-
@pietervn said:
I usually put blu tack / prestic in between the parts, then a few layers of masking tape. The blu tack usually captures all the shavings and very few if any gets into the knife itself. The first one I ever did was only masked off and the awl is still not quite factory snap. The subsequent Pioneer X got the blu tack treatment and all the tools snap as the day it left the factory.Pete
Humm.... Thank's a lot for the tip mate

-
Nice work. I filed the keyring off my Pioneer X, I did ok but I wish I had used your method. I really wish Victorinox would make a keyring\laynard ring that would fold in like in the Leatherman Micra or Wave. That way you could deploy it if you wanted it or not use it.
-
@Farmer X said:
"Smurf file" had me scratching my head. Was that UK terminology I hadn't heard before? Then I got to the end of the first post. I would have understood immediately if the filter substituted the word "illegitimate," but "smurf file" sounds a lot funnier.The profanity filter here removes any word it finds offensive and replaces it with the word “smurf”. Results in some pretty funny stuff, especially when it does it with part of a very common word, e.g. wrissmurfch.
-
@lemo said:
I watched some youtube vids and read some forum posts regarding the removal of the keyring loop from Alox saks. The general recommendation for protecting the scales while filing off the loop is to apply some masking tape. I tried this and found that masking tape provides close to zero protection from a rough file. One slip, and you make a mess of the scales. This is partly my fault, as I always start a job with good intentions of being careful, but then get impatience and make mistakes. So I tried to come up with a foolproof solution.Shim steel.

Masking tape first

Then a strip of shim steel on either side of the loop.



Carelessly file with a large smurf file.

Polish with dremel type tool.

Someone with more patience and talent than myself would not need to go to this extra trouble, but it was nice to know there was pretty much no way I could mess this up.


Edit 'smurf file' = Forum censored the term used for a 'rough' file.

Very good and precise work.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
