Single-wing Wingman
-
Kampfer, what did you have to do to get them all to click ?
I'm still thinking about picking one up to mess with.
Easy, file down the drivers to match the pliers pivot then you are good to go. Leave the handle the way it is.
How firm is the driver open retention at the wrong end with the slot filed down compared with the stock open retention at the correct end?
Hoping to get my Wingman tomorrow then I do my version.

-

If I'd read through all the posts I'd have seen my question has already been quasi-answered.
-
@pingu said:

If I'd read through all the posts I'd have seen my question has already been quasi-answered.
It depends how much you file down. On the one I did it is quite a bit firmer that the stock end. Also I cut in a deep backstop so they open a little past the straight line of the handle to reduce the chance of them closing up onto your hand.
-
Just adding a couple comments.
I think scissors make this tool awesome. I didn't have any spare and that was a downer. However, if you leave the plier spring in and rework the tools, I'm not sure there is enough there to do that with the scissors. It is possible that to have scissors you have to remove the plier spring. Or put them down the other end, someone else can try that.
The second is an issue of tension. I reworked the tools so they opened easily about a quarter open, then a little firmer to half open. This was to allow easy access to the tools below. What I failed to note before I did this was that the spring no longer held them shut. Because they share a fastener with the knife what happens is if you tighten it to keep the tools in the knife is hard to open, if you loosen it so the knife opens easily then the tools are loose. Learn from my mistake maybe.
Sadly my OCD prevents me from ever being able to enjoy these tools in both stock and hacked form. Mostly because of the handle shape. I liked the plier head, the flat and phillips drivers, the package opener etc. I can see why others might like them but they're not for me.
I can't believe some of you have made multiples now.
-
Never had you for an OCD type, mate...quite surprised, actually

-
Kampfer, what did you have to do to get them all to click ?
I'm still thinking about picking one up to mess with.
Easy, file down the drivers to match the pliers pivot then you are good to go. Leave the handle the way it is.
How firm is the driver open retention at the wrong end with the slot filed down compared with the stock open retention at the correct end?
Hoping to get my Wingman tomorrow then I do my version.

Same tension as the pliers head.

-
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
-
@zoidberg said:
What I failed to note before I did this was that the spring no longer held them shut.Well that reminds me of my first ever attempted hack - trying to make a Gerber Evo non-locking :ahhh. A complete fail but its not impossible the Gerber PE will make a reappearance in my Wi-man

Thanks for the great heads-up.
-
@Cupboard said:
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
I was thinking the same about the can opener but doesn't lifting a possibly "stuck" tool require a degree of retention?
Funny you should ask about the "file" hardness. Was also thinking about that, I have a plan too, and had just done a test grind with a diamond burr. Not obviously harder or unworkable though maybe that is because it is thinner.
-
What I failed to note before I did this was that the spring no longer held them shut.
Well that reminds me of my first ever attempted hack - trying to make a Gerber Evo non-locking :ahhh. A complete fail but its not impossible the Gerber PE will make a reappearance in my Wi-man

Thanks for the great heads-up.
No problem mate.
Better others don't make the same mistake. -
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
I was thinking the same about the can opener but doesn't lifting a possibly "stuck" tool require a degree of retention?
Funny you should ask about the "file" hardness. Was also thinking about that, I have a plan too, and had just done a test grind with a diamond burr. Not obviously harder or unworkable though maybe that is because it is thinner.
You two might want to see this.

-
@zoidberg said:
I can see why others might like them but they're not for me.Yeah, I'm with you on this one mate
Both in stock form, and as this mod, I really can't connect with it. It's like the whole is worse than the sum of it's parts. Each individual feature is not too bad, but collectively I don't like them at all. I bought a Wingman for the scissors, and the rest of it is just sat in a box destined to never be utilised unless I decide to add some of the parts to a PST or something (I have been tempted to repurpose the package opener).As a pliers tool, the handles have pointy bits so you have to hold it the correct way round, but even then the handles are too splayed for comfort. As a knife based tool, the blade locks and the drivers don't - which is completely the reverse of what I'd want.
But yes ... I can see why it might appeal more to others who may have different priorities and preferences
-
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
I was thinking the same about the can opener but doesn't lifting a possibly "stuck" tool require a degree of retention?
Funny you should ask about the "file" hardness. Was also thinking about that, I have a plan too, and had just done a test grind with a diamond burr. Not obviously harder or unworkable though maybe that is because it is thinner.
You two might want to see this.

How can I ever reveal what mod I have just done to my Wingman "file"
. Not that I would have ever used it for prying but I do have in mind some gentle "driving".Fortunately this very moment a cheap knock-off keychain multifunction tool has arrived for serious paint tin opening.
-
@Cupboard said:
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.This was the same thing I was thinking, and changed my tool up last night.

Those with keen eyes might note that I had to take off the tip of the small serrated blade. Otherwise, it would close far enough that the tip could pass through the hole in the bottom of the handle, and I really didn't feel like owning a tool that let me stab myself. Also, I've put the Wingman's semi serrated blade on this, because I wanted the Sidekick's blade on my Wingman.
@Cupboard said:
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.I think zoidberg's link covers my recent experience. It IS hardened, but I don't know how much.
With this tool swap, I don't have much concern about no retention on the file/small driver or the (remains of) the small serrated blade. And honestly, I've tested can openers before with almost zero retention. It just slows the process down. Unlike with screw drivers where you can bust your knuckles if they collapse on you. This setup is much more to my liking.
-
It was your experience that had me thinking. You want the shaft to be tough and the tip to be hard otherwise that happens.
I think once I've sorted my insurance out, finished tidying my house, got some wrapping paper, picked up some boots for my mum... I might have a fiddle and see :)
@50ft-trad said:
As a pliers tool, the handles have pointy bits so you have to hold it the correct way round, but even then the handles are too splayed for comfort. As a knife based tool, the blade locks and the drivers don't - which is completely the reverse of what I'd want.I hadn't realised how played they are, but comparing them to my Rebar it's a huge difference!

And I agree about the drivers too.
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop

-
@Cupboard said:
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop
Exactly this.
I am confused by people's willingness to take these things completely apart to frankenstein them, sometimes at significant effort, but being unwilling to take one apart to make adjustments to the tool in mostly-stock configuration.
Also, I've tested before the force the drivers will take, and I have to intentionally TRY to get them to collapse when they have the spring retention. So, I've never felt locking was any kind of necessity.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


Now that has given me a dilemma but an option I didn't think I had...