firearms
-
@Chako said:
Thanks for the video. Now I am unsure if the local shop has the 550 B or 550 BL. Guess I may have to visit them sometime soon to check that press out.If it's $500 it most likely the 550B. You can download Dillon's latest (monthly) catalog here:
http://www.dillonprecision.com/#/articles.htmlIn addition to the consumable parts (brass, powder, primer, bullets) you will need an accurate scale of some kind. You will need to verify the powder setting on the loading press by weighing the powder. I would recommend a scale that can measure 0.1 grain increments. There are manual (balance beam) types and electronic types, depending on what you want to use and how much you want to spend.
You are going to need to measure the velocity of the bullets being shot. So you'll need a chronograph. Even if your not that concerned about accuracy, it is difficult to know what results you are getting from your loading if you don't know what the velocities of the bullets are.
Your probably going to need a bullet puller, because you will make mistakes and need to safely remove the bullets sometimes.
You'll probably want a primer tray for helping you load primers into the primer pickup tube to load the Dillon primer feed.
http://www.dillonprecision.com/content/p/9/catid/3/pid/23608/Dillon_Primer_Flip_TrayThere is probably lots of stuff I'm not thinking about right now. Pick up two or three loading manuals and read them.
Cleaning brass for reuse. That's another issue and more equipment.
-
I wouldn't go that far. They are selling a 9mm only square B for the same price as that 550. So can't base anything on price.
Thanks for the good info.

-
@Chako said:
I wouldn't go that far. They are selling a 9mm only square B for the same price as that 550. So can't base anything on price.Thanks for the good info.

The SDB comes set up for loading including one set of dies. The 550B and 550BL do not come with dies. You buy them separately.
I bought a used SDB on Fleabay for ~$230. It included one set of dies. To buy a new 550B the regular price is $439 (plus the cost of the
dies sold separate.) A set of dies can run $50 to $100 or more for a set. It would have been about twice as much for me. -
Here's a cheaper way to go than reloading…

-
This is another one I find hilarious.

-
:D
-
LMAO!
Nate
That's us mobile -
Well I bought the Dillon Square Deal B for the 9mm. After talking to a few experienced club members, they told me reloading for pistol was the way to go. Later, if I need to load rifle, to get a single stage press on the cheap later on. From what they told me, it made a lot of sense.
So now I have the press with 9mm dies, 3 extra small primer tubes, and a primer flip tray which was thrown in free for good measure.
Next on the agenda will be an electronic scale and a tumbler. After that, set up the press and buy some bullets, primers, and powder, and maybe a bag of 9mm brass to get started.
-
This reminds me, I've got a set of 45 Colt dies for the SDB I'm not using. I may put them in the trade forum.
-
@Chako said:
Well I bought the Dillon Square Deal B for the 9mm. After talking to a few experienced club members, they told me reloading for pistol was the way to go. Later, if I need to load rifle, to get a single stage press on the cheap later on. From what they told me, it made a lot of sense.So now I have the press with 9mm dies, 3 extra small primer tubes, and a primer flip tray which was thrown in free for good measure.
Next on the agenda will be an electronic scale and a tumbler. After that, set up the press and buy some bullets, primers, and powder, and maybe a bag of 9mm brass to get started.
Sounds great. The only advice I can offer is to go slow and ONLY reload while not distracted. Make it the one and only thing you are doing. Do not get sidetracked and make sure to focus on what you are doing. If not you can easily make a mistake. I would also weigh the rounds after they are loaded to make sure you did not double load them.
-
Good advice.
-
I heard something today that triggered my bullsmurfometer,and I want to double check with the brain trust...
The guy claims to have a 9mm auto,and to use it in practical pistol comps in Hong Kong. He claims to have had a smokestack type jam which caused $600 damage to the gun.
I've seen and cleared these kind of jams on 19/22s,but,being in the UK Havnt seen it with a centre fire pistol. The story struck me as rubbish. Your opinions please!
-
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.
-
@kirk13 said:
I heard something today that triggered my bullsmurfometer,and I want to double check with the brain trust...The guy claims to have a 9mm auto,and to use it in practical pistol comps in Hong Kong. He claims to have had a smokestack type jam which caused $600 damage to the gun.
I've seen and cleared these kind of jams on 19/22s,but,being in the UK Havnt seen it with a centre fire pistol. The story struck me as rubbish. Your opinions please!
A failed extractor is not going to cause damage, it's just bloody annoying, aka stovepipe, can be caused by duff rounds and bad cleaning
-
@SAK Guy said:
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.- 1
If it happens regularly some people will have the ejection port enlarged, which can get pricey. If it happened to me on a regular basis I'd sell the gun.
Stovepiping is an occasional problem, particularly on some old guns, which is why there is an immediate action clearing drill. One of my pistols stovepipes regularly with a certain type of ammo (Blazer aluminum case), but works 100% with everything else.
-
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.
- 1
If it happens regularly some people will have the ejection port enlarged, which can get pricey. If it happened to me on a regular basis I'd sell the gun.
Stovepiping is an occasional problem, particularly on some old guns, which is why there is an immediate action clearing drill. One of my pistols stovepipes regularly with a certain type of ammo (Blazer aluminum case), but works 100% with everything else.
In my opinion if you have to enlarge your ejection port something is not functioning properly. I would fix that problem rather than enlarge the ejection port.
-
Thank you gents! Bullsmurf confirmed

-
Another vote of total bravo sierra. Most stove pipes are caused by magazines, ammo. As CS said thats why there is IAC drills.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

