firearms
-
:D
-
LMAO!
Nate
That's us mobile -
Well I bought the Dillon Square Deal B for the 9mm. After talking to a few experienced club members, they told me reloading for pistol was the way to go. Later, if I need to load rifle, to get a single stage press on the cheap later on. From what they told me, it made a lot of sense.
So now I have the press with 9mm dies, 3 extra small primer tubes, and a primer flip tray which was thrown in free for good measure.
Next on the agenda will be an electronic scale and a tumbler. After that, set up the press and buy some bullets, primers, and powder, and maybe a bag of 9mm brass to get started.
-
This reminds me, I've got a set of 45 Colt dies for the SDB I'm not using. I may put them in the trade forum.
-
@Chako said:
Well I bought the Dillon Square Deal B for the 9mm. After talking to a few experienced club members, they told me reloading for pistol was the way to go. Later, if I need to load rifle, to get a single stage press on the cheap later on. From what they told me, it made a lot of sense.So now I have the press with 9mm dies, 3 extra small primer tubes, and a primer flip tray which was thrown in free for good measure.
Next on the agenda will be an electronic scale and a tumbler. After that, set up the press and buy some bullets, primers, and powder, and maybe a bag of 9mm brass to get started.
Sounds great. The only advice I can offer is to go slow and ONLY reload while not distracted. Make it the one and only thing you are doing. Do not get sidetracked and make sure to focus on what you are doing. If not you can easily make a mistake. I would also weigh the rounds after they are loaded to make sure you did not double load them.
-
Good advice.
-
I heard something today that triggered my bullsmurfometer,and I want to double check with the brain trust...
The guy claims to have a 9mm auto,and to use it in practical pistol comps in Hong Kong. He claims to have had a smokestack type jam which caused $600 damage to the gun.
I've seen and cleared these kind of jams on 19/22s,but,being in the UK Havnt seen it with a centre fire pistol. The story struck me as rubbish. Your opinions please!
-
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.
-
@kirk13 said:
I heard something today that triggered my bullsmurfometer,and I want to double check with the brain trust...The guy claims to have a 9mm auto,and to use it in practical pistol comps in Hong Kong. He claims to have had a smokestack type jam which caused $600 damage to the gun.
I've seen and cleared these kind of jams on 19/22s,but,being in the UK Havnt seen it with a centre fire pistol. The story struck me as rubbish. Your opinions please!
A failed extractor is not going to cause damage, it's just bloody annoying, aka stovepipe, can be caused by duff rounds and bad cleaning
-
@SAK Guy said:
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.- 1
If it happens regularly some people will have the ejection port enlarged, which can get pricey. If it happened to me on a regular basis I'd sell the gun.
Stovepiping is an occasional problem, particularly on some old guns, which is why there is an immediate action clearing drill. One of my pistols stovepipes regularly with a certain type of ammo (Blazer aluminum case), but works 100% with everything else.
-
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.
- 1
If it happens regularly some people will have the ejection port enlarged, which can get pricey. If it happened to me on a regular basis I'd sell the gun.
Stovepiping is an occasional problem, particularly on some old guns, which is why there is an immediate action clearing drill. One of my pistols stovepipes regularly with a certain type of ammo (Blazer aluminum case), but works 100% with everything else.
In my opinion if you have to enlarge your ejection port something is not functioning properly. I would fix that problem rather than enlarge the ejection port.
-
Thank you gents! Bullsmurf confirmed

-
Another vote of total bravo sierra. Most stove pipes are caused by magazines, ammo. As CS said thats why there is IAC drills.
-
@captain spaulding said:
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.
- 1
If it happens regularly some people will have the ejection port enlarged, which can get pricey. If it happened to me on a regular basis I'd sell the gun.
Stovepiping is an occasional problem, particularly on some old guns, which is why there is an immediate action clearing drill. One of my pistols stovepipes regularly with a certain type of ammo (Blazer aluminum case), but works 100% with everything else.
In my opinion if you have to enlarge your ejection port something is not functioning properly. I would fix that problem rather than enlarge the ejection port.
Enlarging the ejection port is a fairly standard modification on 1911s set up for ISPC. When you're shooting in competition every little advantage helps.
-
@captain spaulding said:
Bullsmurf......unless his gunsmith charges $600 an hour to change an ejector/extractor/firing pin.
- 1
If it happens regularly some people will have the ejection port enlarged, which can get pricey. If it happened to me on a regular basis I'd sell the gun.
Stovepiping is an occasional problem, particularly on some old guns, which is why there is an immediate action clearing drill. One of my pistols stovepipes regularly with a certain type of ammo (Blazer aluminum case), but works 100% with everything else.
In my opinion if you have to enlarge your ejection port something is not functioning properly. I would fix that problem rather than enlarge the ejection port.
Enlarging the ejection port is a fairly standard modification on 1911s set up for ISPC. When you're shooting in competition every little advantage helps.
Ah, for ISPC yes. I thought we were talking personal firearms for range, hunting use.
-
I have heard a few club members make this statement:
"The 1911 was top of its game, back in 1912".
I puzzled over this statement until I saw an IPSC competition held at the club. I saw more 1911's jam during competition than I would care to see. I was and am still curious at shooting a .45 1911, but since that day, have put on the shelf my buying one to sate my curiosity. I plan to see if I can try someone else's 1911 down the road instead.
With that said, I have my IPSC course this weekend. Going to start tomorrow at 8 am sharp and go until 6ish, and repeat on Sunday. Looking forward to it, and also packing 700 rounds of factory 9 mm just in case I need it.

Also, I went back to the only local gun shop (and the only place I can buy re-loading stuff locally) to see if I could buy some components for my Dillon Square Deal B press. I quickly found out they had plenty of small primers, brass, and that is about it. I wanted to buy a digital scale...no go. I wanted to buy 115 grain bullets...no go (they only had cast lead bullets in 125 grains). I wanted to buy some accessories for the press...no go. Best yet, I wanted to buy some powder...no go. Looks like I may have to make another 3.5 hour drive to Sudbury to find something somewhat local.
I did find that my ultrasonic cleaner works nicely on spent brass. The water only didn't do that great a job, so I added a little jewelry cleaner to the mix. Next on my list is some brasso or something like that. I may or may not need a rotary tumbler down the road. I have an old rock tumbler somewhere, but I think it is well and truly buried under a lot of stuff. If memory serves me correct, it may be too small to be of much use anyways.
-
@Chako said:
I have heard a few club members make this statement:"The 1911 was top of its game, back in 1912".
I puzzled over this statement until I saw an IPSC competition held at the club. I saw more 1911's jam during competition than I would care to see. I was and am still curious at shooting a .45 1911, but since that day, have put on the shelf my buying one to sate my curiosity. I plan to see if I can try someone else's 1911 down the road instead.
With that said, I have my IPSC course this weekend. Going to start tomorrow at 8 am sharp and go until 6ish, and repeat on Sunday. Looking forward to it, and also packing 700 rounds of factory 9 mm just in case I need it.

Also, I went back to the only local gun shop (and the only place I can buy re-loading stuff locally) to see if I could buy some components for my Dillon Square Deal B press. I quickly found out they had plenty of small primers, brass, and that is about it. I wanted to buy a digital scale...no go. I wanted to buy 115 grain bullets...no go (they only had cast lead bullets in 125 grains). I wanted to buy some accessories for the press...no go. Best yet, I wanted to buy some powder...no go. Looks like I may have to make another 3.5 hour drive to Sudbury to find something somewhat local.
I did find that my ultrasonic cleaner works nicely on spent brass. The water only didn't do that great a job, so I added a little jewelry cleaner to the mix. Next on my list is some brasso or something like that. I may or may not need a rotary tumbler down the road. I have an old rock tumbler somewhere, but I think it is well and truly buried under a lot of stuff. If memory serves me correct, it may be too small to be of much use anyways.
I usually buy all components on-line except for those with a $ hazard charge $ (powder and primers). There has been issues with finding powder and primers in recent years with the ammo scares. I can usually find what I want at gun shows. If you are talking about practice ammo or competition handgun ammo, you might consider copper plated bullets. They are very well priced and you can buy them on-line. I recently bought some from this company, they have good prices, cheap shipping and you can buy from them directly.
http://www.xtremebullets.com/9mm-s/9666.htm
I would look at MidwayUSA, Brownells or other on-line sources for electronic scales.
-
The reason those 1911's are jamming during competition is that they're too tight. Pick up an issue .45 and it will rattle. Those loose tolerances are what keeps them running. There's a reason that the US military kept them as standard issue for 71 years, and they're still seeing combat 103 years later.......
-
@jerseydevil said:
The reason those 1911's are jamming during competition are that they're too tight. Pick up an issue .45 and it will rattle. Those loose tolerances are what keeps them running. There's a reason that the US military kept them as standard issue for 71 years, and they're still seeing combat 103 years later.......+1 Other non standard things like heavy recoil springs (messes up the mechanical timing of the design causing the extractor to ride over the rim), barrel bushings fitted too tightly etc. I been shooting 1911's since 1976 and I can count jams on one hand. Most were due to worn out mags or crummy reloads....then there was that match where I was hip shooting though a cut square in a plywood barrier....held too high and my rear sight clipped the plywood during recoil...that caused a stoppage.

There are a lot of good pistol designs out there but for me, the 1911 is still the most natural pointing and easiest to shoot accurately...

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
