firearms
-
@jerseydevil said:
The reason those 1911's are jamming during competition are that they're too tight. Pick up an issue .45 and it will rattle. Those loose tolerances are what keeps them running. There's a reason that the US military kept them as standard issue for 71 years, and they're still seeing combat 103 years later.......+1 Other non standard things like heavy recoil springs (messes up the mechanical timing of the design causing the extractor to ride over the rim), barrel bushings fitted too tightly etc. I been shooting 1911's since 1976 and I can count jams on one hand. Most were due to worn out mags or crummy reloads....then there was that match where I was hip shooting though a cut square in a plywood barrier....held too high and my rear sight clipped the plywood during recoil...that caused a stoppage.

There are a lot of good pistol designs out there but for me, the 1911 is still the most natural pointing and easiest to shoot accurately...

-
@Chako said:
I have heard a few club members make this statement:**"The 1911 was top of its game, back in 1912". **
Who ever is making that statement is showing their ignorance. That sounds real tough down at the club with the boys but is bravo sierra in the real world. I use to shoot a little IDPA at a local range for fun. For me it was just fun and extra pratice. I'm not very competitive by nature. One day one of the young studs asked me where I learned to shoot like that. He said your not the fastest shot out here but you dont miss. My reply was I learned a long time a go you cant shoot fast enough to make up misses and if you lay your shooting foundations correctly and maintain them the rest will follow. I was shooting a stock Springfield 1911 Loaded. I cut my teeth reading gun cranks like Elmer Keith, Col. Charlie Askins, Jeff Cooper, Bill Jordon, Skeeter Skelton etc.. As Clint Smith says shoot till your happy! :)
-
Jeff Cooper would approve of your 1911 David. Mr. Keith and Mr. Skelton , however...... ;)
-
@jerseydevil said:
Jeff Cooper would approve of your 1911 David. Mr. Keith and Mr. Skelton , however...... ;)Tom I just happen to have a few revolvers those gentelmen would approve of. :D
-
I have heard a few club members make this statement:
**"The 1911 was top of its game, back in 1912". **
Who ever is making that statement is showing their ignorance. That sounds real tough down at the club with the boys but is bravo sierra in the real world. I use to shoot a little IDPA at a local range for fun. For me it was just fun and extra pratice. I'm not very competitive by nature. One day one of the young studs asked me where I learned to shoot like that. He said your not the fastest shot out here but you dont miss. My reply was I learned a long time a go you cant shoot fast enough to make up misses and if you lay your shooting foundations correctly and maintain them the rest will follow. I was shooting a stock Springfield 1911 Loaded. I cut my teeth reading gun cranks like Elmer Keith, Col. Charlie Askins, Jeff Cooper, Bill Jordon, Skeeter Skelton etc.. As Clint Smith says shoot till your happy! :)
Gee, we grew up reading the same authors...
My guns are stock except for aftermarket grips and one has a Brown Precision Solid Barrel Bushing (in place of the Colt collet bushing). -
Forgot to post this the other day I think.
Even though I have had a CCW non stop for over 10 years in other states. Former law enforcement officer and over 25 years in the military I still had to take a class in Texas for there CCW.
Oh well any excuse to shoot is ok by me.
Took the new CZ P 07 with trigger work by Cajun Gun Works. Best pistol trigger I have ever used by far.

Brought Lovechild along just in case but she was not needed.

The course of fire was easy with shots from 3,7 and 15 yards. Perfect score in case you was wondering.
-
I guess one can either be a 1911 fan or not. Either way, I do want to try one very much. I have tried a .40 and didn't much care for it. Mind you, that was my very first pistol to try and I was startled at how violent the kick was. I much prefer the 9 mm. I haven't tried a 45 yet. I was told by several folks that the 45 is much more pleasant to shoot than the 40.
Harley, nice CZ.
-
Just got back from another visit to the local gun shop. This time, the owners were around and it appeared that they had everything I was looking for yesterday...just that their employee didn't know anything in regards to stock.
I took their last powder, a 1lb Hodgdon HP-38 container. I also bought 1 package of cast lead 115 grain bullets in 500 quantity to get me started. She was telling me that the 124 grain bullet would take less powder...something to consider on my next bullet buy. I also bought 1000 Winchester small primers, a Hornady rotary tumbler, corn cob medium, a bottle of medium rejuvenation, and an electronic scale accurate to 0.1g. Get this, they had them in the archery area to weight arrows.

Now all I need to do is after my course this weekend, figure where to install my press upstairs, go buy two or so bolts to install it, and I should be in business after a little room cleaning.

I was told that those steel Russian 9 mm casings I lovingly picked up and cleaned may not work in the press. I bought two bags of 100 brass casings just in case. I also have some shot once Remington brass. So worse case scenario, I should have around 400 spent casings. Going to try one of those metal casings when I can...so I won't throw them out just yet.
Does anyone know if those metal 9 mm cases will work, or should I just toss them and focus on the brass?
-
Brass. Never heard of steel cases reloaded....no elasticity like brass.
-
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.
One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
-
Got it. Going to do something with the steel ones then. I won't waste my time with them from now on. I am going to use the rest of my Russian ammo for my black badge course...so I won't have to worry about picking them up. Guess I won't be saving a few bucks buying Barnaul 9 mm in the future from this point on.

-
@ColoSwiss said:
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
I had heard some stuff about Colt...very sad. Mine are Early 80's-90's and the bulk of mine in the past were Series 70's guns. Out of 20+ Colt 1911s (Govts, Commanders and Gold Cups), never a bad one...never.
I strayed and bought a different 1911 brand only once....the old timers will probably remember MS Safari Arms. Shot three rounds out of it....on the 3rd shot, the front red insert flew out and the hammer fell to half cock. It went back the next day and I had my traded in stock Government Model back in my hands.
Now, that ain't to say I didn't mix in some Browing HPs, Smiths, Colts and Rugers occasionally! :D
-
@captain spaulding said:
Brass. Never heard of steel cases reloaded....no elasticity like brass.
This. ^^^
Just toss the steel case stuff.
Getting steel cases stuck in your nice new SDB won't be enjoyable. Throw them away. I wouldn't recommend reloading aluminum cases either. 9mm brass is easy to come by, perhaps the easiest brass to find.
-
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.
One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
I had heard some stuff about Colt...very sad. Mine are Early 80's-90's and the bulk of mine in the past were Series 70's guns. Out of 20+ Colt 1911s (Govts, Commanders and Gold Cups), never a bad one...never.
I strayed and bought a different 1911 brand only once....the old timers will probably remember MS Safari Arms. Shot three rounds out of it....on the 3rd shot, the front red insert flew out and the hammer fell to half cock. It went back the next day and I had my traded in stock Government Model back in my hands.
Now, that ain't to say I didn't mix in some Browing HPs, Smiths, Colts and Rugers occasionally! :D
Had a Series 70 9mm that was so accurate I had custom sights installed. Decided in a weak moment it was too large and heavy for the load and the mag capacity, so sold it. :ahhh
The CZ Shadow came along later and is a good replacement. Live and learn (sometimes).
-
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.
One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
I had heard some stuff about Colt...very sad. Mine are Early 80's-90's and the bulk of mine in the past were Series 70's guns. Out of 20+ Colt 1911s (Govts, Commanders and Gold Cups), never a bad one...never.
I strayed and bought a different 1911 brand only once....the old timers will probably remember MS Safari Arms. Shot three rounds out of it....on the 3rd shot, the front red insert flew out and the hammer fell to half cock. It went back the next day and I had my traded in stock Government Model back in my hands.
Now, that ain't to say I didn't mix in some Browing HPs, Smiths, Colts and Rugers occasionally! :D
Had a Series 70 9mm that was so accurate I had custom sights installed. Decided in a weak moment it was too large and heavy for the load and the mag capacity, so sold it. :ahhh
The CZ Shadow came along later and is a good replacement. Live and learn (sometimes).
The CZ designs are solid...always wanted to try a 75!

-
@captain spaulding said:
Took apart the Remington 870 shotgun tonight and boy, what a mess it was. Learning quickly that sometimes, the local gun shop is a mess. I got the shotgun back from the local shop after they had to use a Dremel on two dimples inside the magazine tube. Once gone, it allows full access to the extension tube.
Well, got the shotgun back and took it out to the range, and damaged the second factory red dot sight. Noted after a few rounds something was really off. It felt like there was a lot of sand in it. I quickly stopped and thought to myself...no he didn't did he?
Well tonight was the first time I was able to take it apart. Man oh man, you should have seen the metal shavings. The local shop Dremeled away the two dimples alright, without taking the magazine tube off, or shoving any thing in the tube to catch metal shavings. Consequently, all that crap went into the action.

After a good half hour of TLC, the shotgun is feeling better than ever. To whoever did that to my shotgun....

All I keep hearing from you is people at the gun stores doing idiotic things to your guns or just plain acting like dumb asses. If I were you I would stay far away from having anyone work on your firearms unless it is completely necessary. I'm not lecturing you, but you should be doing these simple things yourself. Again, I am not trying to be rude.
Maybe I don't get out much, but don't hear too many gunsmith horror stories in my parts. A bad gunsmith can ruin the rep of a shop and destroy the business pretty quickly. I'm sure there's always gonna be unhappy customers, but this kind of thing is really surprising to me.
Sent from my iPhone using Tapatalk
-
When I get into something, I am not the most knowledgeable sort around on the topic. I tend to depend on those I think are more knowledgeable than I am...that is until I quickly ramp up to speed. I am also the type to read and do extensive research on things. I am a quick learner.
Unfortunately, I still have to depend on the local gun shop for some things. They still have a set of Hi-Point mags on order for me (who knows when those will come in), and a Trueglow red dot sight that should be replaced sometime soon (I hope).
Likewise, they are the only local place to buy things...that is if I would like to stroll into a store and buy things direct. I may have to move my operations online more, or make an other trip to Sudbury.
Their bonehead antics have caused me to buy my last 2 rifles from out of town.
Yes, I am learning. I have talked to several club members, and some of those guys have boycotted the local gun shop since the mid 90s. :ahhh
Anyhow, going to log off, got a full day ahead at the club.

-
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.
One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
I had heard some stuff about Colt...very sad. Mine are Early 80's-90's and the bulk of mine in the past were Series 70's guns. Out of 20+ Colt 1911s (Govts, Commanders and Gold Cups), never a bad one...never.
I strayed and bought a different 1911 brand only once....the old timers will probably remember MS Safari Arms. Shot three rounds out of it....on the 3rd shot, the front red insert flew out and the hammer fell to half cock. It went back the next day and I had my traded in stock Government Model back in my hands.
Now, that ain't to say I didn't mix in some Browing HPs, Smiths, Colts and Rugers occasionally! :D
:)I've had a Colt Combat Commander and Government Model both 70 series from the late seventies. Both of those were modified By James Hoag. No longer have either of those now. My present 1911 is a stock Springfield Loaded of wich I've put an extractor and firing pin stop from Wilson Combat in it. The main problem with the 1911 is its popularity. To many manufactures, gunsmiths and after market accessories that are designed to sell but dont work well have tarnished its reputation. Given a good 1911 and a good gunsmith who knows what they are doing to maintane it. It is my choice in an semi-auto pistol. Why a good gunsmith? If you shoot a lot you will need maintance work on it to keep it running good just like your car. I'm not against other semi-autos there are some good guns out there. Dont tell any one but I do like some of the combat tupperware out there. It just took me 20+ years to get there. :D :D
-
You could just get a Glock or CZ and skip the whole hassle.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login