Off-Brand Challenge - ETHEREALICER - Böker City Tool / SWIZA D04
-
@Etherealicer said:
Under Construction
Here you can see how the scales are attached. The white part has knobs going into the liners (see arrows).
The scales came off easily and were easy to re-attach. Apparently, we have a 4-pin construction. You can also spot the scale attachment points. The white plastic is stiffer and harder, whereas the blue part is rubbery.
So, if the lock button breaks, you can easily replace the scales. Its also super easy, because everything is ONE part, so no fiddling with bits and pieces.
Looking at the construction, I noticed a gap on either side of the blade-spring. The gap is wide enough to push a piece of paper through without problems. :ahhh
I find the tools sticking out of the frame problematic as it leads to a very uncomfortable grip. Still that might just be me. What I find unforgiving is how badly they use the space...The ergonomics is a big issue for me. How bad is it when the blade is open? Does the openers cause discomfort? With the blade closed it doesn´t matter much but of course open is a biggie.
About the paper going through I find thats possible on Victorinox as well.

-
Under Construction
Here you can see how the scales are attached. The white part has knobs going into the liners (see arrows).
The scales came off easily and were easy to re-attach. Apparently, we have a 4-pin construction. You can also spot the scale attachment points. The white plastic is stiffer and harder, whereas the blue part is rubbery.
So, if the lock button breaks, you can easily replace the scales. Its also super easy, because everything is ONE part, so no fiddling with bits and pieces.
Looking at the construction, I noticed a gap on either side of the blade-spring. The gap is wide enough to push a piece of paper through without problems. :ahhh
I find the tools sticking out of the frame problematic as it leads to a very uncomfortable grip. Still that might just be me. What I find unforgiving is how badly they use the space...The ergonomics is a big issue for me. How bad is it when the blade is open? Does the openers cause discomfort? With the blade closed it doesn´t matter much but of course open is a biggie.
About the paper going through I find thats possible on Victorinox as well.

I have only a CT41 with me (stored in my office desk), I cannot push paper through at any layers. Anyway, I put the paper in for visualization, because I'm unsure how well one can see the gap on a picture. Please note, that I can push paper through on both sides of the knife-backspring, so the wider gap is really wide! Because of its width, I noticed it in the first place. Its also something that might be unique to my Swiza and not general.
As for the comfort, for me it's the middle finger that lies uncomfortably on the cap-lifter, when using the blade.

-
I actually can get 3 layers of regular printing paper in (in the large gap). The folded piece is ripped to show that it is double.
I should probably point out that the blade is a liner-lock it technically does not need a back-spring!
So, this is cosmetic and probably a bit of quality/precision point.
-
@Etherealicer said:
I actually can get 3 layers of regular printing paper in (in the large gap). The folded piece is ripped to show that it is double.Wow, Thats a differnt story than Victorinox. You can barely squeeze a paper in on some layers but that is like ventilation vent. That could accumulate a lot of nasty stuff.
-
I actually can get 3 layers of regular printing paper in (in the large gap). The folded piece is ripped to show that it is double.
Wow, Thats a differnt story than Victorinox. You can barely squeeze a paper in on some layers but that is like ventilation vent. That could accumulate a lot of nasty stuff.
I should have made a new post instead of editing my previous :D
We should not forget that the blade is a liner-lock, so the spring is not essential, just reporting what I see

But you are probably right, good space for dirt to get comfortable -
Thanks for the pictures, Etherealicer! Frankly, I don't worry too much about those huge gaps. It means water has a way to get out when washing the knife in a dishwasher, which is one of the more unique features they advertise. Also, it is a good guarantee the backspring isn't so wide it causes bladeplay (which I have seen a couple of times in even rather expensive knives). I'm looking forward to testing a Swiza myself, there are several parts of the design I'm a little skeptical about, but I'll hold off judgement till I have a knife I can fiddle around with.
-
@Steinar said:
Thanks for the pictures, Etherealicer! Frankly, I don't worry too much about those huge gaps. It means water has a way to get out when washing the knife in a dishwasher, which is one of the more unique features they advertise. Also, it is a good guarantee the backspring isn't so wide it causes bladeplay (which I have seen a couple of times in even rather expensive knives). I'm looking forward to testing a Swiza myself, there are several parts of the design I'm a little skeptical about, but I'll hold off judgement till I have a knife I can fiddle around with.Yeah, it will also be interesting to hear an other perspective and have a larger sample group (one knife is statistically irrelevant).
I'm a bit torn. Dislike the way they market themselves (kinda playing at the underdog trying to get free of evil Victorinox) but I do like the scales.
Fun fact: It's the only MT I'm aware off where you can OHO the can-opener, but not the blade :D -
The back-layer Phillips is very pointy and does not work well on PH2 screws (it is advertised as PH1, but a bit of versatility would be desirable).
[/quote]


-
Thank you for doing this review Etherealicer!

-
A very thurough review!
Keep up the good work!Sent from a device made from star dust using tapatalk
-
Thanks guys, you are the best

I have it from a reliable source that soon a Swiza model with saw should be available.

Anyway, tonight the Swiza will have to face the dreaded can, afterwards it will be time to sharpen. -
Yes, if the Classic can do it, every other knife needs to do it too...
O'm pleasant surprised with the knife today. If the grip were more comfortable I could actually like it :D
The awl punched holes into that can like nothing else, twisting to make the holes big showed that the awl has a good bite. At this task it performed well.
The blade is at an odd angle, but that did not keep it to cut through that can. Sliced very well, no serious damage to the edge. Overall, another success

-

Have you tried opening the tools with gloves on?Sent from a device made from star dust using tapatalk
-
@Grathr said:

Have you tried opening the tools with gloves on?Sent from a device made from star dust using tapatalk
Nope but I can try that... let me check...
Windstoppers: yes I can open all the tools, but only by engaging my thumbnail though the fabric. I also can open the main blade on my CT, but it's a bit harder...Will test other gloves...

-

Have you tried opening the tools with gloves on?Sent from a device made from star dust using tapatalk
Nope but I can try that... let me check...
Windstoppers: yes I can open all the tools, but only by engaging my thumbnail though the fabric. I also can open the main blade on my CT, but it's a bit harder...Will test other gloves...
Not sure the CT is a fair comparison, as it's too thick. Maybe try a Spartan/Tinker?

-

Have you tried opening the tools with gloves on?Sent from a device made from star dust using tapatalk
Nope but I can try that... let me check...
Windstoppers: yes I can open all the tools, but only by engaging my thumbnail though the fabric. I also can open the main blade on my CT, but it's a bit harder...Will test other gloves...
Not sure the CT is a fair comparison, as it's too thick. Maybe try a Spartan/Tinker?

I will, but I doubt that is a problem with the windstoppers, the only question is, can you get your nail into the nick. For example, I can open the small blade with about 5 tries, I can't open the metal file as it is further in. I actually think on a thinner model it will be easier to open the main blade, as it is easier accessible (remember, on Vics the nail-nick for the main blade is on the inside).
-
Finally got around to sharpen the Doofer...
Ok, my amateur opinion is that it took more work than it should have.

-

Have you tried opening the tools with gloves on?Sent from a device made from star dust using tapatalk
Nope but I can try that... let me check...
Windstoppers: yes I can open all the tools, but only by engaging my thumbnail though the fabric. I also can open the main blade on my CT, but it's a bit harder...Will test other gloves...
Not sure the CT is a fair comparison, as it's too thick. Maybe try a Spartan/Tinker?

I will, but I doubt that is a problem with the windstoppers, the only question is, can you get your nail into the nick. For example, I can open the small blade with about 5 tries, I can't open the metal file as it is further in. I actually think on a thinner model it will be easier to open the main blade, as it is easier accessible (remember, on Vics the nail-nick for the main blade is on the inside).
Sidenote: thinner SAKs make it easier.
Ok, with thick welding gloves I could not open the Swiza as the awl prevented it (with the open awl I could manage). These are thick gloves but in fairly good condition, often workgloves are stiffer and less grippy at the finger tip, which will make it even harder.
Conglusion:
Opening the tools on the Swiza is much easier than your traditional SAK, but its not built to be opened with thick working gloves.
There are 3 reasons for that for the easier opening:- large hole for better grip
- tools are sticking way more out of the grip (an advantage for opening, disadvantage for grip comfort.)
- Weaker back-spring (its a liner-lock after all)

-
Etherealicer, thanks for the posts. Nice to the Sviza in action for the first time. These guys have potential, but it doesn't look like they are there quite yet.
-
@Etherealicer said:
Finally got around to sharpen the Doofer...Ok, my amateur opinion is that it took more work than it should have.
That's because you're not sharpening freehand yet
those gizmos only work well if the factory angle is less than the angle on the stones, otherwise you're not just sharpening, you're reprofiling ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login