Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Show off your Sak mod's!

Scheduled Pinned Locked Moved The Mod Squad
6.3k Posts 1 Posters 1.2m Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Show off your Sak mod's!
Show off your Sak mod's!
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • magentus Offline
    magentus
    Admin Team
    Posts: 21,659
    magentus Offline
    magentus
    Admin Team
    wrote on last edited by
    #4140 Quote Reply

      @hiraethus said:
      DIY Modeler:

      Top job H! :salute:

      1 Reply Last reply
      • s1xty7 Offline
        s1xty7
        Posts: 305
        s1xty7 Offline
        s1xty7
        wrote on last edited by
        #4141 Quote Reply

          @Sheradin said:
          Thank you all for the info, I have a local hobby shop or two that needs visiting... :tu: I had seen the Apprentice but unfortunately also saw the prices some bring! Figured I'd probably spend twice as much, bugger a couple perfectly serviceable knives, curse a bit, and try to make my own... :)

          Yea, some of those out of production SAKs get crazy expensive. I was lucky enough to have someone give me a beat up Apprentice I was able to get back to functional but I'll probably make up some too. Even though the Apprentice is compact and has a great tool set, the backside phillips has some limitations on strength so I'll likely make up some Scientists. That's another out of production and crazy priced SAK with a good toolset. Its like a 91mm Apprentice with an inline phillips and magnifying glass added and corkscrew on the backside instead of the phillips. I'm not a corkscrew fan nor do I need the small driver it can hold but I haven't seen any non backside tool scales for 91mm or I would drop those altogether.

          Good luck with your mods!!

          1 Reply Last reply
          • ALM Offline
            ALM
            Posts: 116
            ALM Offline
            ALM
            wrote on last edited by
            #4142 Quote Reply

              Titanium Tool 58mm

              1 Reply Last reply
              • windson Offline
                windson
                Posts: 616
                windson Offline
                windson
                wrote on last edited by
                #4143 Quote Reply

                  @ALM said:
                  Titanium Tool 58mm

                  Very nice!

                  1 Reply Last reply
                  • ALM Offline
                    ALM
                    Posts: 116
                    ALM Offline
                    ALM
                    wrote on last edited by
                    #4144 Quote Reply

                      Pioneer with Scissors Burnt Bronze Cerakote. Titanium screws. Brass liners.

                      1 Reply Last reply
                      • Monrogue Offline
                        Monrogue
                        Posts: 23,312
                        Monrogue Offline
                        Monrogue
                        wrote on last edited by
                        #4145 Quote Reply

                          Nice one ALM :tu:

                          Sent from my SM-G920R4 using Tapatalk

                          1 Reply Last reply
                          • Tom Schneider Offline
                            Tom Schneider
                            Posts: 28
                            Tom Schneider Offline
                            Tom Schneider
                            wrote on last edited by
                            #4146 Quote Reply

                              I have one ALM custom and it is amazing!! Now the problem is the more of his work I see the more I want!

                              1 Reply Last reply
                              • hiraethus Offline
                                hiraethus
                                Admin Team
                                Posts: 6,969
                                hiraethus Offline
                                hiraethus
                                Admin Team
                                wrote on last edited by
                                #4147 Quote Reply

                                  Making some brass liners for Pioneers

                                  1 Reply Last reply
                                  • hiraethus Offline
                                    hiraethus
                                    Admin Team
                                    Posts: 6,969
                                    hiraethus Offline
                                    hiraethus
                                    Admin Team
                                    wrote on last edited by
                                    #4148 Quote Reply

                                      This mod is a subtle one:

                                      1 Reply Last reply
                                      • zoidberg Offline
                                        zoidberg
                                        Posts: 38,161
                                        zoidberg Offline
                                        zoidberg
                                        wrote on last edited by
                                        #4149 Quote Reply

                                          @hiraethus said:
                                          Making some brass liners for Pioneers

                                          I like the work pics. :tu: :tu:

                                          1 Reply Last reply
                                          • hiraethus Offline
                                            hiraethus
                                            Admin Team
                                            Posts: 6,969
                                            hiraethus Offline
                                            hiraethus
                                            Admin Team
                                            wrote on last edited by
                                            #4150 Quote Reply

                                              :tu:

                                              I should have taken more, but only managed to snatch a bit of time in the evenings to make a start on these. The process is a bit laborious, but it's nice when they start to really take shape like this.

                                              1 Reply Last reply
                                              • firiki Offline
                                                firiki
                                                Posts: 6,076
                                                firiki Offline
                                                firiki
                                                wrote on last edited by
                                                #4151 Quote Reply

                                                  That's one thick liner right there! :o :D

                                                  :drool: :tu:

                                                  1 Reply Last reply
                                                  • hiraethus Offline
                                                    hiraethus
                                                    Admin Team
                                                    Posts: 6,969
                                                    hiraethus Offline
                                                    hiraethus
                                                    Admin Team
                                                    wrote on last edited by
                                                    #4152 Quote Reply

                                                      :D It's 9 or 10 liners all stacked up so I can shape them in one go. TBH it's a bit thick for my belt sander and fret saw to handle - I'd be better off doing them 4 or 5 at a time.

                                                      1 Reply Last reply
                                                      • firiki Offline
                                                        firiki
                                                        Posts: 6,076
                                                        firiki Offline
                                                        firiki
                                                        wrote on last edited by
                                                        #4153 Quote Reply

                                                          Fret saw? You're cutting them manually?!

                                                          I'm both jealous and inspired. I'll mod me a SAK or three, one day :tu:

                                                          1 Reply Last reply
                                                          • magentus Offline
                                                            magentus
                                                            Admin Team
                                                            Posts: 21,659
                                                            magentus Offline
                                                            magentus
                                                            Admin Team
                                                            wrote on last edited by
                                                            #4154 Quote Reply

                                                              @firiki said:
                                                              Fret saw? You're cutting them manually?!

                                                              I'm both jealous and inspired. I'll mod me a SAK or three, one day :tu:

                                                              Yeah, a SAK of mass destruction

                                                              1 Reply Last reply
                                                              • firiki Offline
                                                                firiki
                                                                Posts: 6,076
                                                                firiki Offline
                                                                firiki
                                                                wrote on last edited by
                                                                #4155 Quote Reply

                                                                  @magentus said:

                                                                  @firiki said:

                                                                  Fret saw? You're cutting them manually?!

                                                                  I'm both jealous and inspired. I'll mod me a SAK or three, one day :tu:

                                                                  Yeah, a SAK of mass destruction

                                                                  And I'll call it magentus' silence (at last)...

                                                                  1 Reply Last reply
                                                                  • hiraethus Offline
                                                                    hiraethus
                                                                    Admin Team
                                                                    Posts: 6,969
                                                                    hiraethus Offline
                                                                    hiraethus
                                                                    Admin Team
                                                                    wrote on last edited by
                                                                    #4156 Quote Reply

                                                                      @firiki said:
                                                                      Fret saw? You're cutting them manually?!

                                                                      I'm both jealous and inspired.

                                                                      :salute:

                                                                      Yep, all manual - except for the belt sander.

                                                                      The way I do it is:

                                                                      Cut the blanks using tin snips (21 mm x 100 mm or so) out of 0.8 mm brass sheet.
                                                                      Flatten the blanks as they get bent during cutting.
                                                                      Drill and deburr one pivot hole in each blank.
                                                                      Stack the liners and clamp together with a single factory liner as a drilling template, using a 3mm pin through the already drilled hole as location.
                                                                      Drill the other two holes in the stack - this ensures that they're all in the same place.
                                                                      Separate out the stack and deburr the holes as necessary
                                                                      Rebuild the stack with a factory liner at each end to act as a guide for the sanding - bolt and rivet together tightly.
                                                                      Hacksaw as much material from the outside as possible.
                                                                      Use belt sander to get the outer edges close to the liners.
                                                                      Use a combination of hack and fret saw to remove the material from the middle.
                                                                      Belt sand the bits in the middle you can get to.
                                                                      Keep going at the shaping with files until very close to the shape of the factory liners, then switch to aluminium oxide/silicon carbide paper and polish to finish.

                                                                      @firiki said:
                                                                      I'll mod me a SAK or three, one day :tu:

                                                                      You really should. :pok:

                                                                      1 Reply Last reply
                                                                      • magentus Offline
                                                                        magentus
                                                                        Admin Team
                                                                        Posts: 21,659
                                                                        magentus Offline
                                                                        magentus
                                                                        Admin Team
                                                                        wrote on last edited by
                                                                        #4157 Quote Reply

                                                                          @firiki said:

                                                                          @magentus said:

                                                                          @firiki said:

                                                                          Fret saw? You're cutting them manually?!

                                                                          I'm both jealous and inspired. I'll mod me a SAK or three, one day :tu:

                                                                          Yeah, a SAK of mass destruction

                                                                          And I'll call it magentus' silence (at last)...

                                                                          will it have a fish scaler?

                                                                          1 Reply Last reply
                                                                          • firiki Offline
                                                                            firiki
                                                                            Posts: 6,076
                                                                            firiki Offline
                                                                            firiki
                                                                            wrote on last edited by
                                                                            #4158 Quote Reply

                                                                              @magentus said:

                                                                              @firiki said:

                                                                              @magentus said:

                                                                              @firiki said:

                                                                              Fret saw? You're cutting them manually?!

                                                                              I'm both jealous and inspired. I'll mod me a SAK or three, one day :tu:

                                                                              Yeah, a SAK of mass destruction

                                                                              And I'll call it magentus' silence (at last)...

                                                                              will it have a fish scaler?

                                                                              Yes, it is useful in pic-nics and other occasions. It will be called magentus' sorrow :angel:

                                                                              1 Reply Last reply
                                                                              • firiki Offline
                                                                                firiki
                                                                                Posts: 6,076
                                                                                firiki Offline
                                                                                firiki
                                                                                wrote on last edited by
                                                                                #4159 Quote Reply

                                                                                  @hiraethus said:

                                                                                  @firiki said:

                                                                                  Fret saw? You're cutting them manually?!

                                                                                  I'm both jealous and inspired.

                                                                                  :salute:

                                                                                  Yep, all manual - except for the belt sander.

                                                                                  The way I do it is:

                                                                                  Cut the blanks using tin snips (21 mm x 100 mm or so) out of 0.8 mm brass sheet.
                                                                                  Flatten the blanks as they get bent during cutting.
                                                                                  Drill and deburr one pivot hole in each blank.
                                                                                  Stack the liners and clamp together with a single factory liner as a drilling template, using a 3mm pin through the already drilled hole as location.
                                                                                  Drill the other two holes in the stack - this ensures that they're all in the same place.
                                                                                  Separate out the stack and deburr the holes as necessary
                                                                                  Rebuild the stack with a factory liner at each end to act as a guide for the sanding - bolt and rivet together tightly.
                                                                                  Hacksaw as much material from the outside as possible.
                                                                                  Use belt sander to get the outer edges close to the liners.
                                                                                  Use a combination of hack and fret saw to remove the material from the middle.
                                                                                  Belt sand the bits in the middle you can get to.
                                                                                  Keep going at the shaping with files until very close to the shape of the factory liners, then switch to aluminium oxide/silicon carbide paper and polish to finish.

                                                                                  @firiki said:
                                                                                  I'll mod me a SAK or three, one day :tu:

                                                                                  You really should. :pok:

                                                                                  I'm certainly eager but if this is to happen radical changes must be made in my life first. Like, getting a bench to work on and getting some more tools and a place to put said bench, also finding the time. Baby is the top priority right now though, things are tough I can tell you. Alternatively, if only I could manage to be granted free access to a friend's workplace...

                                                                                  Thanks for the description of the process :tu: I'm not sure if you're encouraging me or demoralising me, though. :D

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Show off your Sak mod's!
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0