The Hacked Leatherman Owners Club.
-
-
Does anyone know if the t-shank holder from a Supertool 300 EOD fits in a Wave/Charge? From the outside the Rebar and Supertool seems to have the same pivot size

-
@GPS12 said:
Does anyone know if the t-shank holder from a Supertool 300 EOD fits in a Wave/Charge? From the outside the Rebar and Supertool seems to have the same pivot size
I would ask this guy: Toolslinger's SurCharge + Toolslinger's ST300 XD.
Here are some pics of two ST300 awls, one of which I ground down to fit into a Charge.
I've not seen the ST300 t-shank holder in person so I don't know if it could be worked to fit sorry. -
@GPS12 said:
Does anyone know if the t-shank holder from a Supertool 300 EOD fits in a Wave/Charge? From the outside the Rebar and Supertool seems to have the same pivot size
Afraid it won't work. The amount of material that you'd have to remove would seriously compromise the part by the time you got it to fit.
You'd be better off trying to grind a Surge exchanger to fit on the outside like Metro did way back.
-
Thank you for the reply

-
Does anyone know if the t-shank holder from a Supertool 300 EOD fits in a Wave/Charge? From the outside the Rebar and Supertool seems to have the same pivot size

Afraid it won't work. The amount of material that you'd have to remove would seriously compromise the part by the time you got it to fit.
You'd be better off trying to grind a Surge exchanger to fit on the outside like Metro did way back.
What about making the t-shank liner lock compatible, any chance of that happening?
Does anyone have pics of the t-shank not installed? Pics from both sides if possible thanks.
-
Does anyone know if the t-shank holder from a Supertool 300 EOD fits in a Wave/Charge? From the outside the Rebar and Supertool seems to have the same pivot size

Afraid it won't work. The amount of material that you'd have to remove would seriously compromise the part by the time you got it to fit.
You'd be better off trying to grind a Surge exchanger to fit on the outside like Metro did way back.
What about making the t-shank liner lock compatible, any chance of that happening?
Does anyone have pics of the t-shank not installed? Pics from both sides if possible thanks.
Not sure that the EOD one would be convertible to liner lock. The Surge one has been done by Metro in one of his older hack threads.
Next time I have the XD apart for cleaning/tinkering/maintenance I'll try and get some detailed pics and measurements.
-
@Toolslinger said:
Next time I have the XD apart for cleaning/tinkering/maintenance I'll try and get some detailed pics and measurements.Thank you mate.

-
Thank you too!
-
Just for fun today I polished out the blade on my Rebar.

-
Sweet blade

Sent from my SM-G920R4 using Tapatalk
-
That looks great.

-
Thanks guys

-
-
I think I'm gonna dive into my ReCharge Today.
Just gonna pull a bit driver off and swap it with an Awl and Scissors if they will fit.
If I grind down the plier rest inside the handle, can I get away with a longer awl?
Also going to Gun Blue the screws just to get them darker again.
I'd also like to darken the scissors and awl just so they match but in not sure how to go about the scissors......
-
@NKlamerus said:
I think I'm gonna dive into my ReCharge Today.Just gonna pull a bit driver off and swap it with an Awl and Scissors if they will fit.
If I grind down the plier rest inside the handle, can I get away with a longer awl?
Also going to Gun Blue the screws just to get them darker again.
I'd also like to darken the scissors and awl just so they match but in not sure how to go about the scissors......
If you take out the bit driver on the side with the small bit driver, you should be able to fit in the awl, small bit driver, scissors in that side of the frame. The only thing that might be problematic is the height of the awl may interfere with the pliers. I say this because there is some variation in tolerances that allow it to work on some combinations of parts but not all. You can always grind the awl down a bit for more space.
My suggestion is to try it first without touching the plier rest and see if it closes to your satisfaction.
If you do decide to got the route of removing the rest, I found that I could carefully pull the rest and blade retainers off the rivet and then use a punch and hammer to flatten the rivet from the inside of the tool handle. This allowed good lockup of handle tools, extra space for the pliers and tools and meant that I didn't have to try breaking or grinding anything in the handles.
-
I think I'm gonna dive into my ReCharge Today.
Just gonna pull a bit driver off and swap it with an Awl and Scissors if they will fit.
If I grind down the plier rest inside the handle, can I get away with a longer awl?
Also going to Gun Blue the screws just to get them darker again.
I'd also like to darken the scissors and awl just so they match but in not sure how to go about the scissors......
If you take out the bit driver on the side with the small bit driver, you should be able to fit in the awl, small bit driver, scissors in that side of the frame. The only thing that might be problematic is the height of the awl may interfere with the pliers. I say this because there is some variation in tolerances that allow it to work on some combinations of parts but not all. You can always grind the awl down a bit for more space.
My suggestion is to try it first without touching the plier rest and see if it closes to your satisfaction.
If you do decide to got the route of removing the rest, I found that I could carefully pull the rest and blade retainers off the rivet and then use a punch and hammer to flatten the rivet from the inside of the tool handle. This allowed good lockup of handle tools, extra space for the pliers and tools and meant that I didn't have to try breaking or grinding anything in the handles.
Went the wrong route lol
O shortened the awl. Although I didn't really want an awl, I wanted a metal scribe I could draw lines with in paper. So I shortened it.
But the scissors...oh man....
-
Super Wave

</topic/63157
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




