Work in progress: display cabinet
-
Now I can tell you the final colour, or should I make you wait? :)
Make me wait, please. No need to rush things

I know, I know...
Spoiler:
You're waiting for me to put up a "That's what she said" pic, right?...
Well, sorry to disappoint you...[spoiler]
I'm more mature than that, you know?...[spoiler]
I've just one thing to say to you...[spoiler]


[/spoiler]
[/spoiler]
[/spoiler] -
I can't complain, I brought this upon myself :D 
-
Call me old fashioned but I like those details carved in the wood.

This is you:

- :D
Nope, not a fan of whiskey and bourbon. I like a good Bloody Mary though

-
Assembling the carcass. One of the problems I find with pocket screws is that they have a tendency to pull the work out of position as you tighten them down. So to deal with that, I've cut a gauge board to the length of the inside of the cabinet, and clamped it on top of the bottom panel. That gives me something to hold the side panel firmly against as I drive the screws. It'll also ensure that the sides end up the same distance apart at the top and bottom.


-
With the glue set on the carcass, I can test-fit the door. The fit is not too bad. Looking from the front, the gap is pretty even all round. But somehow the carcass has got a bit of a twist in it so my nice flat door does not sit flush
Probably due to uneven tension on the pocket screws. I'm wishing I'd used a different sort of joint now. However I'm optimistic that I'll be able to pull the twist out when I fix it to the wall, if I put a screw in each corner. So hopefully it's fixable.

-
I think (and hope) that little problem can be fixed, shibafu. I like how you didn't use L brackets and that there won't be a door handle, by the way

I'm really enjoying this thread. I love working with wood. Minds outta the gutter, folks
:DWhen I was a kid I wanted to become a carpenter, making pieces of furniture in particular. My parents convinced me this wouldn't pay off. Sometimes I regret listening to them.
-
I can't complain, I brought this upon myself :D 
Dude, really?!
Spoiler:
I mean...

Well, he could have said that as well, couldn't he? Provided he's not one to always want to be right.

Am I missing something? -
A little more progress - I morticed out for the lock on the back of the door.
I also did a bit of experimenting with cutting keyholes on a piece of scrap. I couldn't really figure out how to fit the keyhole escutcheon though. The one I have is called a "thread escutcheon" which is like a lining inside the keyhole, but it has smooth tapered sides and just springs out of the hole again when I try to tap it in. I think I might ditch it and try to find a surface-mounting escutcheon instead.


-
Very neat work and tidy work space there S

(that’s odd there’s a fused clock connector behind your frame
) -
@Sparky415 said:
Very neat work and tidy work space there S
(that’s odd there’s a fused clock connector behind your frame
)If it looks tidy that can only be the result of very selective photography :) There's all sorts of junk piled up on there.
-
Rain all day today so no chance to get outside and do the final couple of routing operations that I need to do on the door. But despite my expectations it turned out to be a good day for the project... a parcel arrived :) Inside are the pieces of acrylic for the shelves and the window in the door. I ordered them cut to size from https://www.trentplastics.co.uk/ . It worked out the same price as buying a 6ft by 2ft sheet of acrylic from the local DIY store, but it saved me a lot of cutting, and they've done a far better job of polishing the edges than I could have.
It's only 3mm acrylic and quite flexible, so the shelves will need to be well supported. I have a plan for that.


-
I also had an idea about my escutcheon vexation: I'm going to try making one. This is just a test piece using some thin brass that I had. I've got some thicker brass plate on order. The design is etched using ferric chloride. It's not perfect but I think the idea is sound.
I'm contemplating whether I should fill in the etched area with some red enamel paint, or leave it as plain brass. Opinions?

-
@shibafu said:
I also had an idea about my escutcheon vexation: I'm going to try making one. This is just a test piece using some thin brass that I had. I've got some thicker brass plate on order. The design is etched using ferric chloride. It's not perfect but I think the idea is sound.I'm contemplating whether I should fill in the etched area with some red enamel paint, or leave it as plain brass. Opinions?
I think red enamel would look excellent!

-
Really looking forward to seeing this completed.

-
@shibafu said:
I'm contemplating whether I should fill in the etched area with some red enamel paint, or leave it as plain brass. Opinions?You could try with nail polish first to see how you like it*. I think red enamel would look splendid though brass has a yellow aspect and past certain proportions it doesn't match well with red, in my opinion. I assume the escutcheon will be placed in the middle of the door's cover?
- :D

- :D
-
@firiki said:
You could try with nail polish first to see how you like it*. I think red enamel would look splendid though brass has a yellow aspect and past certain proportions it doesn't match well with red, in my opinion. I assume the escutcheon will be placed in the middle of the door's cover?Well red nail polish is not really my style :) but I did find a small pot of red enamel in the cupboard so I've put some on my test piece. It seems to be taking a long time to set though, could be the paint is bad as it's very old. Hopefully it will set well enough to allow me to sand it off the raised areas and get an impression of how it looks.
The position is fixed by the dimensions of the lock, which will put it quite close to the edge of the door (13mm from the edge to the centre of the keyhole).
-
This and the next post are yesterday's work. First the last couple of routing operations on the door. A chamfer detail around the inside edge on the front, and a rebate to receive the window on the back.


-
This piece of 1/2" plywood will form the back panel, and the side shelf supports. I've routed 1/8" grooves across it that the shelves will slot into.
The plywood has been in the garage for a while and has grown a bit of mould. Not a problem though. I treated it with some fungicide to kill the mould, and the stain will be covered by paint.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

