The multitool of the automotive world!
-
I'll be taking a drill and my hand tools. I don't have a garage or any place to put my various saws, grinders, sanders etc so they will have to stay here for now.
Our place in Ottawa is small and there's barely enough outdoors space for my Jeep. No garage, no basement space etc.
Def
-
Bummer. Hopefully you two can find a bigger place later.
That's us mobile
-
...so they can become more >:D >:D >:D >:D
-
We are looking at cottages.
But I should probably get a job at some point.
Def
-
since it's black now maybe I need to do a batch of white Lamontagne logos... or a stencil so you can spray it whatever colour you want?
-
Silly wiring question....
The incandescent lights I am taking off were wired up with only one wire. There was a white wire connected to the light, and a black wire that was cut off pretty far back on one side of the trailer, and no black wire (seemingly) on the other side of the trailer.
I'm not very good when it comes to electricity, but don't you need two wires to create a circuit to make things light up?
Any help on sorting this would be appreciated...
Def
-
grounded to the frame?
-
Maybe- don't I need a positive and negative to make a circuit?
Def
-
You do, but if it's grounded to the frame either via a mounting screw, or wire, that will make the circuit.
-
-
I figured that..... but I assume the yellow wire from the light connects to the existing wire and the black just grounds out to the frame?
That doesn't sound right?
Def
-
Yes. Also the mounting bolt on the right is the ground. The black is a ground but is not really needed but double grounding is nice and makes sure you get good connection. Also you would use the black wire if the light was mount on something non metallic, say like a plastic faring or a nose clip.
Did that help any?That's us mobile
-
The confirmation of what to do is very helpful, thanks. My understanding of electricity however, which has always been dangerously slim, has just taken a large step backwards. :D
Def
-
I got my utility trailer back today- the landlord has been storing it at his cottage for the winter, and he has been using it for the weekend, and just returned it today.
I can see it has taken a few hits over the winter, so, as I am planning to take it for an 8 hour (each way) drive this week to go get my boats, I figured I'd better put some time into fixing it up a bit.

The first thing I had to do was fix my wheel jack. The brackets holding it on to the tongue had both been bent- you can see one that I'd already straightened before realizing I should be taking pics.

Both were bent as badly as the bent one in the photo, and I wasn't sure how to go about straightening them. I could have beat them with a hammer, or I could have pressed one of our camp stoves into service to heat the metal, but it occurred to me that I could use the rail on the trailer, the bolts used to hold the wheel jack on the tongue and a little thing called mechanical advantage.

By running one bolt through the most arched point of the bracket, and all the way through the trailer rail and attaching a nut, then a second bolt through another hole to keep it straight I then used my ratchet to turn the nut and pull the bracket to more or less straight again.


In the end I think it made a very significant difference. :D

Here it is all put back together again!

While taking the jack apart at first I noticed another, much more important job would also need to be done- one of the wires from the harness wasn't actually leading anywhere. I know very little about electricity, but I'm pretty sure that low voltage wires like this one have to be connected to something in order to work.

Out came the SOG Sync I, a roll of electrical tape and a roll of silicone stretch and hold tape. I have to say, I know this is blasphemous in this crowd, but I love this stuff more than duct tape. :ahhh

The great thing about wiring this harness (I wired it in a couple of years ago) is that it is nice and simple- you simply match the colors. In this case it was even simpler, as there was only one wire not leading anywhere. The Sync I made short work of the stretch and hold tape I used last time, as well as the electrical tape that was holding a dead end on the wire, which should come as no surprise as SOG seems to always do an amazing job of sharpening things to the point where they are just dangerous to hold, let alone use.

It didn't take much to reconnect the wires, then I wrapped them in electrical tape, and then wrapped the whole thing back up in stretch and hold tape, which should keep the weather out for at least another couple of years.


And that's about it- the trailer is ready to go again. I am maybe going to try and paint it this year as it's pretty scuffed up, but overall it's in great shape and I am glad to have it back, even if it takes up my one and only parking spot.

Def
-
Def, the brackets on the stand would not bend as easy if they were on the other way with the rails aganist the tongue. You have to bend twice as much metal that way. :D
-
Yes but then there would be less contact with the tongue and it might slip a bit more.
What I figure I need are some blocks of wood to fill the large gaps between the tongue and where the bolts are. I hate bolting something that is bolted that far away from the piece it is supposed to be attached to.
Def
-
Nice work, however, two things.
- The duct tape comment
- Why don't you have a miners wrench?
:D Just messing with ya boss.
-
I had a feeling that you wouldn't like the duct tape comment, but I love that silicone tape and I use it everywhere.
As for the miner's wrench, what's the difference between that and the big adjustable wrench in the background of the pics?
I also have pipe wrenches if you think I need to go bigger. :D
Def
-
Miner's wrench has a Precision thumb detector on it. :D
I -
I just use the big head on that adjustable as a thumb detector.
It is more effective than I'd like to admit. :ahhh
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
