Show off your Sak mod's!
-
@JamesJ said:
<u>I want to make one 91mm "main" multi-tool as my EDC and alternative (hopefully a little thinner) to a Swisschamp. Mainly used for working on bicycles and music gear, cutting moleskin and tape, fixing all types of gadgets on the go, often in urban environments. The tools would be (not particular layer order yet):</u>•Pen Blade across from** Nail file** (from Compact) - Thinking about replacing the outer plate that has the little raised section (for the modern/thinner main blade) with a flat one, and using both of the little spacers that come with the pen blade/nail fail and keeping the spring standard thickness...but not sure how this would mesh together...basically trying to get pen blade and nail file in the same layer. EDIT: to clarify, there would be no large blade at all
•Cap Lifter across from Can Opener
•Pliers
•Scissors
•Metal file/saw (stainless/latest version)
•Inline PhillipsHere's one I made a while back which is close to what you're aiming for:

Deluxe Modeler, or Swisschamp with the saw and scaler removed. You should be able to re-use the pins as long as you're careful drilling the heads off. It might be possible to put the metal saw/file opposite the small blade - something I've been meanign to try for a while, but not got round to. I don't think the Compact hook/nail file will work at all on the front side of the knife, but the Cadet/Sportsman file should fit in place of the small blade.@JamesJ said:
<u>The other knife would be my 110mm "campsite" knife mainly for food/beverages and firewood and whhhilderness adventures:</u>•Can/Bottle Layer
•Main Blade (bottom half serrated to get rid of that nick and help with cutting ropes, top half plain for cutting potatoes and enemy ninjas)
•Wood Saw (figure I don't need this unless I'm around a camp fire and from what I've seen the 110mm saw is a little nicer length for actually sawing things)
•Cork Screw (from Compact) -will the corkscrew from the Compact work on a 110mm knife? I'm thinking it's the same.
•Nylon Scales (by default for this size, but also because it's gonna get tossed around a bit) -are the nylon scales better for re-use than cellador? I'm thinking the nylon material would chip away less when pulling the scales off, leaving a tighter fit when re-attaching.This is an existing model: the Rucksack, though you'll need to add your own serrations.
Welcome to the forum, and good luck with the mods.

-
-
@jaya_man said:
Is the tool on the lower right of the pic what you meant? Hmmm... Might be a tall order putting that as an inline tool...
Sent from my iPhone using Tapatalk
No, this one from the 110mm knife...goes under the scissors...I wanna have it go under the regular size inline phillips (which is thicker)

-
@hiraethus said:
Here's one I made a while back which is close to what you're aiming for:

Deluxe Modeler, or Swisschamp with the saw and scaler removed. You should be able to re-use the pins as long as you're careful drilling the heads off. It might be possible to put the metal saw/file opposite the small blade - something I've been meanign to try for a while, but not got round to. I don't think the Compact hook/nail file will work at all on the front side of the knife, but the Cadet/Sportsman file should fit in place of the small blade.That would be a model I'd want to collect for sure...black scales feel right for that one too, I always feel like the SAK is wearing a little tux with those black scales.
MS opposite small blade...hmmm...using spacers on both tools on a layer that's wider than either of them? Like putting the MS in the large blade slot?
I have another question about MS, WS, and scaler...on my Champs I see the fish scaler and wood saw sharing a layer, and the scaler has no back tool. They each have a spring, so the springs are against each other, and the side of the back tool is resting against the spring of the scaler.
If I was going to have WS and MS (no scaler) right next to each other, would I need anything between them?...not sure how they do it on knives that only have those 2 of the 3. It would mean the back tools - chisel and fine flathead - would also be rubbing against each other and "torqueing"/twisting in the case of the screwdriver. Also I see the thickest plate on the Champs is between MS and WS, and it has no cutout at all, as if to say the WS and MS must not ever touch...
@hiraethus said:
This is an existing model: the Rucksack, though you'll need to add your own serrations.Ah...I will definitely mention that in the upcoming teardown/build (aka "bloopers reel") video. I'm still pretty lost on the 110 and 58 model names...I was considering the Hercules for a while, then S557 (pre and post Vic versions), but I feel like I prefer my "toolsy" SAKs at 91mm, then just blades at 110mm. Seems a little silly to have that ergonomic handle and then a 20 layer knife...which of course now I want to see and buy. That WorkchampXL is pretty crazy but seemed like mostly just funny shaped blades were added.
-
Here's one I made a while back which is close to what you're aiming for:

Deluxe Modeler, or Swisschamp with the saw and scaler removed. You should be able to re-use the pins as long as you're careful drilling the heads off. It might be possible to put the metal saw/file opposite the small blade - something I've been meanign to try for a while, but not got round to. I don't think the Compact hook/nail file will work at all on the front side of the knife, but the Cadet/Sportsman file should fit in place of the small blade.That would be a model I'd want to collect for sure...black scales feel right for that one too, I always feel like the SAK is wearing a little tux with those black scales.
MS opposite small blade...hmmm...using spacers on both tools on a layer that's wider than either of them? Like putting the MS in the large blade slot?
I have another question about MS, WS, and scaler...on my Champs I see the fish scaler and wood saw sharing a layer, and the scaler has no back tool. They each have a spring, so the springs are against each other, and the side of the back tool is resting against the spring of the scaler.
If I was going to have WS and MS (no scaler) right next to each other, would I need anything between them?...not sure how they do it on knives that only have those 2 of the 3. It would mean the back tools - chisel and fine flathead - would also be rubbing against each other and "torqueing"/twisting in the case of the screwdriver. Also I see the thickest plate on the Champs is between MS and WS, and it has no cutout at all, as if to say the WS and MS must not ever touch...
@hiraethus said:
This is an existing model: the Rucksack, though you'll need to add your own serrations.Ah...I will definitely mention that in the upcoming teardown/build (aka "bloopers reel") video. I'm still pretty lost on the 110 and 58 model names...I was considering the Hercules for a while, then S557 (pre and post Vic versions), but I feel like I prefer my "toolsy" SAKs at 91mm, then just blades at 110mm. Seems a little silly to have that ergonomic handle and then a 20 layer knife...which of course now I want to see and buy. That WorkchampXL is pretty crazy but seemed like mostly just funny shaped blades were added.
Based on experience, a liner is required between the MS and WS... And a specific liner is required for the WS... Otherwise proper closing of WS would not be achieved...
Sent from my iPhone using Tapatalk
-

A liner similar to the one in this pic (minus the area marked with a sharpee) or the full liner similar to WS layer pic I shared earlier will be fine.
Sent from my iPhone using Tapatalk
-

A sneak peak of my on-going project... Just waiting on a donor sak to arrive to complete my build... [emoji8][emoji8][emoji8]

Sent from my iPhone using Tapatalk
-
-
It's just the normal spring... Looks black due to both camera angle and lighting... [emoji23]
Sent from my iPhone using Tapatalk
-
Another sneak peak... Only about 90% complete... Still needs some finishing... [emoji16]

Sent from my iPhone using Tapatalk
-
Lookin great!

-
Can't wait to see the 100%

-
Yes, work faster jaya_man! We need to know.

-
A liner similar to the one in this pic (minus the area marked with a sharpee) or the full liner similar to WS layer pic I shared earlier will be fine.
Ah yes I see now...a variation in the liners......red Champ (2007 on the package, has gray magnifier), you can see it has a solid, thick plate between MS and WS, USA flag Champ has the newer file and liner like your photo.
2 of my 3 donor knives showed up today, still waiting on the 110mm
Seeing your wood scales in progress has me considering making some purpleheart scales...but I don't wanna give up tweezers...

-

A liner similar to the one in this pic (minus the area marked with a sharpee) or the full liner similar to WS layer pic I shared earlier will be fine.
Ah yes I see now...a variation in the liners......red Champ (2007 on the package, has gray magnifier), you can see it has a solid, thick plate between MS and WS, USA flag Champ has the newer file and liner like your photo.
2 of my 3 donor knives showed up today, still waiting on the 110mm
Seeing your wood scales in progress has me considering making some purpleheart scales...but I don't wanna give up tweezers...
Cant wait to finish my project... Cant wait to see yours completed... ☕️
Sent from my iPhone using Tapatalk
-
Damascus Electrician X
I have just seen this and all I can say is :ahhh :ahhh :ahhh :ahhh !
It is gonna be an understatement if I say I fell in love with this!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

