CyberTool owners thread
-
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi.
...and that was the last that was ever seen of it, because immediately after taking this photo I dropped it, it rolled under a cabinet, and disappeared into some alternate dimension!

Are you Pozi-tive it's gone?
-
@Archibald Tuttle said:
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi.
...and that was the last that was ever seen of it, because immediately after taking this photo I dropped it, it rolled under a cabinet, and disappeared into some alternate dimension!

Are you Pozi-tive it's gone?
This calls for a closer Philinspection...
-
Question for the Cybertool owners in here. According to the SAKWiki the Cybertool comes with the following drivers:
[pre]Phillips (Pozidrive) 0 / 1
Slotted 4 mm / Phillips 2
Hex 4 mm / Torx #8
Torx #10 / #15[/pre]I am curious about the Pozidrive Phillips 0 / 1 bit. Does that work on regular Phillips 0 and 1 screws just as well as a normal Phillips driver would?
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi. But like all Phillips drivers, with care they will generally work OK on a pozi screw. Better than the other way around - using a pozi driver on a Phillips screw is usually a disaster.
This is good too hear with my cybertool in the mail. Any idea why the wiki says the bit is posidrive? Perhaps it comes both ways depending on manufacture date and/or market?
-
@Archibald Tuttle said:
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi.
...and that was the last that was ever seen of it, because immediately after taking this photo I dropped it, it rolled under a cabinet, and disappeared into some alternate dimension!

Are you Pozi-tive it's gone?
This calls for a closer Philinspection...
He's screwed.
-
@50ft-trad said:
@Archibald Tuttle said:
[quote author=shibafu link=topic=50953.msg1540191#msg1540191 date=1503142791]
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi....and that was the last that was ever seen of it, because immediately after taking this photo I dropped it, it rolled under a cabinet, and disappeared into some alternate dimension!

Are you Pozi-tive it's gone?
This calls for a closer Philinspection...
He's screwed.
[/quote]Or nuts...? -
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi.
...and that was the last that was ever seen of it, because immediately after taking this photo I dropped it, it rolled under a cabinet, and disappeared into some alternate dimension!

Between or under the floorboards? Inside the wall?
If not, it went where you didn't expect it to go. :ahhh -
@GoatDragon said:
This is good too hear with my cybertool in the mail. Any idea why the wiki says the bit is posidrive? Perhaps it comes both ways depending on manufacture date and/or market?They only come as Phillips' bits. The reference to Pozidriv is probably due to error or confusion.
-
@Little Tinker said:
@Little Tinker said:
They only come as Phillips' bits. The reference to Pozidriv is probably due to error or confusion.
Although while looking at the 2015 catalogue I see Victorinox themselves say "41. – bit Phillips 0 (Pozidrive)", etc ::)
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
-
@GoatDragon said:
.My comment above this one might matter to you

-
@Mechanickal said:
Just found out...My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
-
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
Hmm. Most of the cross head screws here are pozidriv. And most of those are #2. And most of the rest fit a #2 pozidriv screwdriver.
If you are picking two screwdrivers to own around here, you only need a flat head and a #2 pozidriv.
Bad state of affairs here for SAK screwdriver lovers. :P -
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
New CT41: PH0 + PH1
Old CT34: PZ0 + PZ1 -
I shall rename it, Cybercool

-
-
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
New CT41: PH0 + PH1
Old CT34: PZ0 + PZ1All - I hate to resurrect a thread that has not had any recent replies but I want to confirm some items stated. Everywhere I look the bits for cybertool are listed as Phillips (pozidrive). See below from the Cybertool 34 product page
bit Phillips 2
bit Phillips 0 (Pozidrive)
bit Phillips 1 (Pozidrive)I am interested in pulling the trigger on a 34 but am concerned about using the pozidrive bits in phillips screws (most common screw that I come across). If they are indeed mis-labeled I will immediately purchase one. Or if anyone can put my fears to rest that the 0 and 1 bits work fine in phillips screws I would appreciate it.
??? -
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
New CT41: PH0 + PH1
Old CT34: PZ0 + PZ1All - I hate to resurrect a thread that has not had any recent replies but I want to confirm some items stated. Everywhere I look the bits for cybertool are listed as Phillips (pozidrive). See below from the Cybertool 34 product page
bit Phillips 2
bit Phillips 0 (Pozidrive)
bit Phillips 1 (Pozidrive)I am interested in pulling the trigger on a 34 but am concerned about using the pozidrive bits in phillips screws (most common screw that I come across). If they are indeed mis-labeled I will immediately purchase one. Or if anyone can put my fears to rest that the 0 and 1 bits work fine in phillips screws I would appreciate it.
???Resurection old threads is not a drama here at all ;)
PZ and PH bits shouldn't be used on the other type of screw.
It'll damage the screw and possibly the bit too.
Some retailers have all bits in stock. Any retailer should be able to order one for you. It should be around €4 - $5 a piece. -
Thanks for the reply! Ok. I guess the really confusing thing is that in some images of the bits by themselves they LOOK like phillips but are labeled pozi. And sometimes they are clearly pozi bits, but only labeled as phillips. Im in the US market and I have been searching online for a place to buy the bits. But the picture/labeling is scaring me off.
Can you recommend a retailer that would have the phillips 0 and 1 bit?Example on Amazon of a pozi picture with phillips label:
https://www.amazon.com/VICTORINOX-CYBERTOOL-BIT-PHILLIPS-A768020/dp/B000MLSS6A/ref=pd_sbs_468_4?_encoding=UTF8&psc=1&refRID=55P8TA22GDHH5RB56PDMExample on Amazon of Phillips Picture with Pozi label:
https://www.amazon.com/Victorinox-Cybertool-Positive-Bit-Multi-Tool/dp/B000PL4DZ2/ref=sr_1_3?ie=UTF8&qid=1514311685&sr=8-3&keywords=cybertool+bitTo add to the confusion, some images of the tool itself have pictures of regular phillips in the bit holder, but are labeled as pozi.
??? ??? ???
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login