CyberTool owners thread
-
@50ft-trad said:
@Archibald Tuttle said:
[quote author=shibafu link=topic=50953.msg1540191#msg1540191 date=1503142791]
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi....and that was the last that was ever seen of it, because immediately after taking this photo I dropped it, it rolled under a cabinet, and disappeared into some alternate dimension!

Are you Pozi-tive it's gone?
This calls for a closer Philinspection...
He's screwed.
[/quote]Or nuts...? -
Left to right: Phillips 0, Vic Cybertool 0, Pozi 0. The Cybertool bits are Phillips not pozi.
...and that was the last that was ever seen of it, because immediately after taking this photo I dropped it, it rolled under a cabinet, and disappeared into some alternate dimension!

Between or under the floorboards? Inside the wall?
If not, it went where you didn't expect it to go. :ahhh -
@GoatDragon said:
This is good too hear with my cybertool in the mail. Any idea why the wiki says the bit is posidrive? Perhaps it comes both ways depending on manufacture date and/or market?They only come as Phillips' bits. The reference to Pozidriv is probably due to error or confusion.
-
@Little Tinker said:
@Little Tinker said:
They only come as Phillips' bits. The reference to Pozidriv is probably due to error or confusion.
Although while looking at the 2015 catalogue I see Victorinox themselves say "41. – bit Phillips 0 (Pozidrive)", etc ::)
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
-
@GoatDragon said:
.My comment above this one might matter to you

-
@Mechanickal said:
Just found out...My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
-
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
Hmm. Most of the cross head screws here are pozidriv. And most of those are #2. And most of the rest fit a #2 pozidriv screwdriver.
If you are picking two screwdrivers to own around here, you only need a flat head and a #2 pozidriv.
Bad state of affairs here for SAK screwdriver lovers. :P -
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
New CT41: PH0 + PH1
Old CT34: PZ0 + PZ1 -
I shall rename it, Cybercool

-
-
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
New CT41: PH0 + PH1
Old CT34: PZ0 + PZ1All - I hate to resurrect a thread that has not had any recent replies but I want to confirm some items stated. Everywhere I look the bits for cybertool are listed as Phillips (pozidrive). See below from the Cybertool 34 product page
bit Phillips 2
bit Phillips 0 (Pozidrive)
bit Phillips 1 (Pozidrive)I am interested in pulling the trigger on a 34 but am concerned about using the pozidrive bits in phillips screws (most common screw that I come across). If they are indeed mis-labeled I will immediately purchase one. Or if anyone can put my fears to rest that the 0 and 1 bits work fine in phillips screws I would appreciate it.
??? -
@Little Tinker said:
Just found out...
My brand new CT41 has a double Philips bit.
My older CT34 (crossbow tang stamp) came with a double Pozidriv bit!! :ahhh
PZ0 and PZ1? Strange that the #2 size wouldn't be the same style, esp. as it's the one I'd use most often!
New CT41: PH0 + PH1
Old CT34: PZ0 + PZ1All - I hate to resurrect a thread that has not had any recent replies but I want to confirm some items stated. Everywhere I look the bits for cybertool are listed as Phillips (pozidrive). See below from the Cybertool 34 product page
bit Phillips 2
bit Phillips 0 (Pozidrive)
bit Phillips 1 (Pozidrive)I am interested in pulling the trigger on a 34 but am concerned about using the pozidrive bits in phillips screws (most common screw that I come across). If they are indeed mis-labeled I will immediately purchase one. Or if anyone can put my fears to rest that the 0 and 1 bits work fine in phillips screws I would appreciate it.
???Resurection old threads is not a drama here at all ;)
PZ and PH bits shouldn't be used on the other type of screw.
It'll damage the screw and possibly the bit too.
Some retailers have all bits in stock. Any retailer should be able to order one for you. It should be around €4 - $5 a piece. -
Thanks for the reply! Ok. I guess the really confusing thing is that in some images of the bits by themselves they LOOK like phillips but are labeled pozi. And sometimes they are clearly pozi bits, but only labeled as phillips. Im in the US market and I have been searching online for a place to buy the bits. But the picture/labeling is scaring me off.
Can you recommend a retailer that would have the phillips 0 and 1 bit?Example on Amazon of a pozi picture with phillips label:
https://www.amazon.com/VICTORINOX-CYBERTOOL-BIT-PHILLIPS-A768020/dp/B000MLSS6A/ref=pd_sbs_468_4?_encoding=UTF8&psc=1&refRID=55P8TA22GDHH5RB56PDMExample on Amazon of Phillips Picture with Pozi label:
https://www.amazon.com/Victorinox-Cybertool-Positive-Bit-Multi-Tool/dp/B000PL4DZ2/ref=sr_1_3?ie=UTF8&qid=1514311685&sr=8-3&keywords=cybertool+bitTo add to the confusion, some images of the tool itself have pictures of regular phillips in the bit holder, but are labeled as pozi.
??? ??? ??? -
@Gable151 said:
Thanks for the reply! Ok. I guess the really confusing thing is that in some images of the bits by themselves they LOOK like phillips but are labeled pozi. And sometimes they are clearly pozi bits, but only labeled as phillips. Im in the US market and I have been searching online for a place to buy the bits. But the picture/labeling is scaring me off.
Can you recommend a retailer that would have the phillips 0 and 1 bit?Example on Amazon of a pozi picture with phillips label:
https://www.amazon.com/VICTORINOX-CYBERTOOL-BIT-PHILLIPS-A768020/dp/B000MLSS6A/ref=pd_sbs_468_4?_encoding=UTF8&psc=1&refRID=55P8TA22GDHH5RB56PDMExample on Amazon of Phillips Picture with Pozi label:
https://www.amazon.com/Victorinox-Cybertool-Positive-Bit-Multi-Tool/dp/B000PL4DZ2/ref=sr_1_3?ie=UTF8&qid=1514311685&sr=8-3&keywords=cybertool+bitTo add to the confusion, some images of the tool itself have pictures of regular phillips in the bit holder, but are labeled as pozi.
??? ??? ???Ah...
I'm European so I can't help you with that.
Maybe you should ask around in the "tools wanted" section.
Other members might be able to help... -
@Gable151 said:
Thanks for the reply! Ok. I guess the really confusing thing is that in some images of the bits by themselves they LOOK like phillips but are labeled pozi. And sometimes they are clearly pozi bits, but only labeled as phillips. Im in the US market and I have been searching online for a place to buy the bits. But the picture/labeling is scaring me off.
Can you recommend a retailer that would have the phillips 0 and 1 bit?Example on Amazon of a pozi picture with phillips label:
https://www.amazon.com/VICTORINOX-CYBERTOOL-BIT-PHILLIPS-A768020/dp/B000MLSS6A/ref=pd_sbs_468_4?_encoding=UTF8&psc=1&refRID=55P8TA22GDHH5RB56PDMExample on Amazon of Phillips Picture with Pozi label:
https://www.amazon.com/Victorinox-Cybertool-Positive-Bit-Multi-Tool/dp/B000PL4DZ2/ref=sr_1_3?ie=UTF8&qid=1514311685&sr=8-3&keywords=cybertool+bitTo add to the confusion, some images of the tool itself have pictures of regular phillips in the bit holder, but are labeled as pozi.
??? ??? ???I know we've been talking about this in the other thread, I was wrong about them being Pozidrive bits. All the bits I've ever had in a Cybertools look like the Philips and I've only acquired them within the past few years. It appears that Victorinox has switched to a Philips bit and simply kept the PH/PZ label as there might be more PH->PZ compatibility. Perhaps a lot of this confusion stems from the fact that Victorinox cross drivers tend to be made to fit a variety of recessed fasteners.
A lightbulb lit up in my head about this topic after reading this post. The FUNNY thing about the two Amazon links you posted is I've already purchased BOTH items and BOTH showed up looking like Philips. I bought them for the exact same reasons you did: I wanted a dedicated Philips driver and not the pozidrive.
A lot of my personal confusion stems from the fact that Pozidrive is not very common in the US so I'm not entirely familiar with them and I couldn't connect the differences together. Digging a bit deeper, I checked some regular 1/4" bits I have in my tool kit and the Cybertool bit sure looks like a Philips with only very minuscule differences. It's always seemed to work in Philips screws and the times it didn't could be because the screws were not Philips or they are were out of spec (a common issue with electronics today). It doesn't help that Victorinox is muddying the waters by having both drivers listed.
Now here's the linchpin to tie it all together. When I replied to you I forgot I got something else from Victorinox since the last time I ordered those Cybertool bits: A Swisstool Spirit with a full tool kit and inside is a Philips #0 bit. What does it resemble? The Cybertool tool #0/#1 bit. This photo is taken with the included bit from a brand new "back-up" Cybertool I purchased last year, it also matches the bit from the one I currently use. I also have a Cybertool 41 from Japan and it has the same bit as well. AND it matches all the replacement bits I own.
Gable, time to order up that Cybertool! ;)

-
Thanks for the reply! Ok. I guess the really confusing thing is that in some images of the bits by themselves they LOOK like phillips but are labeled pozi. And sometimes they are clearly pozi bits, but only labeled as phillips. Im in the US market and I have been searching online for a place to buy the bits. But the picture/labeling is scaring me off.
Can you recommend a retailer that would have the phillips 0 and 1 bit?Example on Amazon of a pozi picture with phillips label:
https://www.amazon.com/VICTORINOX-CYBERTOOL-BIT-PHILLIPS-A768020/dp/B000MLSS6A/ref=pd_sbs_468_4?_encoding=UTF8&psc=1&refRID=55P8TA22GDHH5RB56PDMExample on Amazon of Phillips Picture with Pozi label:
https://www.amazon.com/Victorinox-Cybertool-Positive-Bit-Multi-Tool/dp/B000PL4DZ2/ref=sr_1_3?ie=UTF8&qid=1514311685&sr=8-3&keywords=cybertool+bitTo add to the confusion, some images of the tool itself have pictures of regular phillips in the bit holder, but are labeled as pozi.
??? ??? ???I know we've been talking about this in the other thread, I was wrong about them being Pozidrive bits. All the bits I've ever had in a Cybertools look like the Philips and I've only acquired them within the past few years. It appears that Victorinox has switched to a Philips bit and simply kept the PH/PZ label as there might be more PH->PZ compatibility. Perhaps a lot of this confusion stems from the fact that Victorinox cross drivers tend to be made to fit a variety of recessed fasteners.
A lightbulb lit up in my head about this topic after reading this post. The FUNNY thing about the two Amazon links you posted is I've already purchased BOTH items and BOTH showed up looking like Philips. I bought them for the exact same reasons you did: I wanted a dedicated Philips driver and not the pozidrive.
A lot of my personal confusion stems from the fact that Pozidrive is not very common in the US so I'm not entirely familiar with them and I couldn't connect the differences together. Digging a bit deeper, I checked some regular 1/4" bits I have in my tool kit and the Cybertool bit sure looks like a Philips with only very minuscule differences. It's always seemed to work in Philips screws and the times it didn't could be because the screws were not Philips or they are were out of spec (a common issue with electronics today). It doesn't help that Victorinox is muddying the waters by having both drivers listed.
Now here's the linchpin to tie it all together. When I replied to you I forgot I got something else from Victorinox since the last time I ordered those Cybertool bits: A Swisstool Spirit with a full tool kit and inside is a Philips #0 bit. What does it resemble? The Cybertool tool #0/#1 bit. This photo is taken with the included bit from a brand new "back-up" Cybertool I purchased last year, it also matches the bit from the one I currently use. I also have a Cybertool 41 from Japan and it has the same bit as well. AND it matches all the replacement bits I own.
Gable, time to order up that Cybertool! ;)
Ha!! First of all thank you for verifying that I am not crazy and the world is mad and it’s not me. Secondly I appreciate you going above and beyond! Guess what? I pulled the trigger earlier today on a sapphire cybertool M. It was just too perfect looking and I took the chance. Delivery is Saturday. I’ll verify the bits that I get and let everyone know.

-
You are definitely not crazy Gable, Victorinox has a long history of driving collectors nuts trying sort out names, model numbers and revisions. Keeps us busy I guess! :) I'm glad you ordered the CT34. I've gotten more use out it than just about any tool I carry, SAK or otherwise. And those translucent blue scales glisten especially in sunlight! Good choice!
-
Thanks for the reply! Ok. I guess the really confusing thing is that in some images of the bits by themselves they LOOK like phillips but are labeled pozi. And sometimes they are clearly pozi bits, but only labeled as phillips. Im in the US market and I have been searching online for a place to buy the bits. But the picture/labeling is scaring me off.
Can you recommend a retailer that would have the phillips 0 and 1 bit?Example on Amazon of a pozi picture with phillips label:
https://www.amazon.com/VICTORINOX-CYBERTOOL-BIT-PHILLIPS-A768020/dp/B000MLSS6A/ref=pd_sbs_468_4?_encoding=UTF8&psc=1&refRID=55P8TA22GDHH5RB56PDMExample on Amazon of Phillips Picture with Pozi label:
https://www.amazon.com/Victorinox-Cybertool-Positive-Bit-Multi-Tool/dp/B000PL4DZ2/ref=sr_1_3?ie=UTF8&qid=1514311685&sr=8-3&keywords=cybertool+bitTo add to the confusion, some images of the tool itself have pictures of regular phillips in the bit holder, but are labeled as pozi.
??? ??? ???I know we've been talking about this in the other thread, I was wrong about them being Pozidrive bits. All the bits I've ever had in a Cybertools look like the Philips and I've only acquired them within the past few years. It appears that Victorinox has switched to a Philips bit and simply kept the PH/PZ label as there might be more PH->PZ compatibility. Perhaps a lot of this confusion stems from the fact that Victorinox cross drivers tend to be made to fit a variety of recessed fasteners.
A lightbulb lit up in my head about this topic after reading this post. The FUNNY thing about the two Amazon links you posted is I've already purchased BOTH items and BOTH showed up looking like Philips. I bought them for the exact same reasons you did: I wanted a dedicated Philips driver and not the pozidrive.
A lot of my personal confusion stems from the fact that Pozidrive is not very common in the US so I'm not entirely familiar with them and I couldn't connect the differences together. Digging a bit deeper, I checked some regular 1/4" bits I have in my tool kit and the Cybertool bit sure looks like a Philips with only very minuscule differences. It's always seemed to work in Philips screws and the times it didn't could be because the screws were not Philips or they are were out of spec (a common issue with electronics today). It doesn't help that Victorinox is muddying the waters by having both drivers listed.
Now here's the linchpin to tie it all together. When I replied to you I forgot I got something else from Victorinox since the last time I ordered those Cybertool bits: A Swisstool Spirit with a full tool kit and inside is a Philips #0 bit. What does it resemble? The Cybertool tool #0/#1 bit. This photo is taken with the included bit from a brand new "back-up" Cybertool I purchased last year, it also matches the bit from the one I currently use. I also have a Cybertool 41 from Japan and it has the same bit as well. AND it matches all the replacement bits I own.
Gable, time to order up that Cybertool! ;)
Ha!! First of all thank you for verifying that I am not crazy and the world is mad and it’s not me. Secondly I appreciate you going above and beyond! Guess what? I pulled the trigger earlier today on a sapphire cybertool M. It was just too perfect looking and I took the chance. Delivery is Saturday. I’ll verify the bits that I get and let everyone know.

It came today! I am happy to say that the phillips bits are true phillips! So far it is Glorious! Surprisingly it does not feel all THAT much different in the pocket than the deluxe tinker!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login